Manuale d’uso / di manutenzione del prodotto SVR61V-29FX del fabbricante Scag Power Equipment
Vai alla pagina of 65
OPERA TOR’S MANUAL Part No. 03269 Rev. 1 Printed 12/10 Printed in USA © 2010 Scag Power Equipment Division of Metalcraft of Mayville, Inc. Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower.
W ARNING F AILURE T O FOLLO W SAFE OPERA TING PRA CTICES MA Y RESUL T IN SERIOUS INJUR Y OR DEA TH. Read this manual completely as well as other man uals that came with your mow er . • AL W A YS FOLLOW OSHA APPR O VED OPERA TION. • DO NO T operate on steep slopes.
I R T able of Contents T able of Contents GENERAL INFORMA TION SECTION 1 - ................................................................................... 1 1.1 INTRODUCTION .........................................................................
II R T able of Contents ADJUSTMENTS SECTION 6 - ................................................................................................. 20 6.1 P ARKING BRAKE ADJUSTMENT ........................................................................
1 R Section 1 INTRODUCTION 1.1 Y our mower was built to the highest standards in the industr y . Howe v er , the prolonged life and maximum efficiency of your mower depends on you follo wing the operating, maintenance and adjustment instructions in this manual.
2 R Section 1 SYMBOLS 1.4 SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke T ransmission P ar king Brak e 48071S Spinning Blade On/Star t Spring T ension on Idler Off/Stop Oil F alling Hazard Thrown Object.
3 R Section 2 INTRODUCTION 2.1 Y our mo wer is only as saf e as the operator . Carelessness or operator error ma y result in ser ious bodily injur y or death.
4 R Section 2 DO NO T allow children to ride or play on the 3. machine, it is not a to y . Clear the area to be mow ed of objects that could be 4. pick ed up and thrown by the cutter b lades. DO NO T carr y passengers. 5. DO NO T operate the machine under the influence of 6.
5 R Section 2 Star t the engine with the operator in the operating 6. position, cutter blades are disengaged, parking brak e is engaged, and the neutral le ver is in neutral. If the mower discharge e ver plugs , shut off the 7. engine, remo v e the ignition ke y , and wait f or all mov ement to stop before remo ving the obstruction.
6 R Section 2 Tie the mow er down securely using the tie do wn 21. points located on the front and rear of the machine. See Figure 2-2 and 2-3. Secure using straps, chains, cable , or ropes. Both front and rear straps must be directed down and outw ard from machine.
7 R Section 2 USING A SP ARK ARREST OR 2.6 The engine in this machine is not equipped with a spar k arrestor muffler . It is in violation of Calif or nia Public Resource Code Section 4442 to use or op.
8 R Section 2 SAFETY AND INSTRUCTIONAL DECALS 2.8 483407 483402 484281 483406 2009 SVR Safety Decals Molded in Fuel T ank 484075 WARNING Operation of this equipment may create sparks that can start res around d ry vegetation. A spark arrestor may be required.
9 R Section 3 SPECIFICA TIONS ENGINE 3.1 General T ype ................................................................................................ Heavy Duty Industrial/Commercial Gasoline Brand ...................................................
10 R Section 3 CUTTER DECK 3.4 T ype ..................................................................................................................
11 R Section 4 CA UTION Do not attempt to operate this mo wer unless you have read this man ual. Learn the location and purpose of all contr ols and instruments bef ore you operate this mo wer . CONTROLS AND INSTR UMENT 4.1 IDENTIFICA TION Bef ore operating the mower , f amiliarize yourself with all mow er and engine controls.
12 R Section 4 Left Steering Control (Figure 4-1). 6. Used to control the mower's left wheel when tr aveling f orward or re v erse. See Section 4.5 for further details regarding the mower's tr avel controls . Right Steering Control (Figure 4-1).
13 R Section 4 GROUND TRA VEL AND STEERING 4.5 - IMPORT ANT - If you are not f amiliar with the operation of a machine with le ver steering and/or h ydrostatic transmissions , the steering and ground speed operations should be learned and practiced in an open area, aw ay from buildings, f ences, or obstructions.
14 R Section 4 PUSH FOR FOR W ARD PULL BA CK FOR REVERSE “N” FOR NEUTRAL LOCK “D” FOR DRIVE NEUTRAL Forward / Re verse Controls Figure 4-2. WHILE TRA VELING FORW ARD,PULL BA CK ON RIGHT STEERING CONTROL TO STEER RIGHT WHILE TRA VELING FORW ARD , PULL BA CK ON LEFT STEERING CONTROL TO STEER LEFT Steering Controls Figure 4-3.
15 R Section 4 T o disengage the deck drive, push the s witch in to 3. the disengage position. Alwa ys operate the engine at full throttle to properly 4. maintain cutting speed. If the engine star ts to lug down, reduce the f orward speed and allow the engine to operate at maximum RPM.
16 R Section 4 If the discharge chute becomes clogged, shut off 1. the engine and remov e the ignition key . Using a stick or similar item, dislodge the clogged material.
17 R Section 5 CONDITION CA USE CURE STRINGERS - OCCASIONAL BLADES OF UNCUT GRASS Width of Deck SGB020 Low engine RPM Run engine at full RPM Ground speed too f ast Slow speed to adjust f or conditions.
18 R Section 5 CONDITION CA USE CURE U N E V E N C U T O N F L A T G RO U ND - WA V Y H I G H -L OW APPEARANCE, SCALLOPED CUT , OR ROUGH CONT OUR Width of Deck SGB020 Lift worn from blade Replace blad.
19 R Section 5 CONDITION CA USE CURE SCALPING - BLADES HITTING DI RT OR CU TT ING VER Y CLO SE T O THE GROUND Width of Deck SGB022 Low tire pressures Check and adjust pressures Ground speed too f ast .
20 R Section 6 P ARKING BRAKE ADJUSTMENT 6.1 W ARNING DO NO T operate the mower if the parking brake is not operab le. P ossible severe injur y could result. The par king brake linkage should be adjusted whene ver the parking brak e lev er is placed in the “ENGA GE” position and the parking brak e will allow the mo wer to move .
21 R Section 6 NEUTRAL ADJUSTMENT -NO TE- Neutral has been set by your Scag dealer at the time of set up and nor mally does not need to be adjusted. If , ho we ver , you find that the neutral has come out of adjustment, f ollow the procedure below . Be sure the dump v alves are in the run position and 1.
22 R Section 6 -NO TE- Bef ore proceeding with this adjustment, be sure that the caster wheels tur n freely and that the tire pressure in the dr iv e wheels is correct. If the tire pressure is not correct, the machine will pull to the side with the low er pressure.
23 R Section 6 CUTTER DECK LEVEL The cutter deck should be le vel from side-to-side f or proper cutting performance. T o chec k f or le vel, be sure that the mow er is on a flat, lev el surf ace, the tires are properly inflated and the cutter deck is set at the most common cutting height that y ou will use.
24 R Section 6 CUTTER DECK ADJUSTMENT BOL T CUTTER DECK ADJUSTMENT BOL T Cutter Deck Pitc h Adjustment Figure 6-5. CUTTER DECK HEIGHT The cutter dec k height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge .
25 R Section 6 Rotate the cutter blade on the right side of the cutter 6. deck. P osition the cutter blade so it is f acing "front to back" on the machine . Check the measurement from the floor to the cutter 7. blade tip at the front and rear of the right side blade .
26 R Section 6 1 2 3 4 A B 1 2 3 4 A B Custom-Cut Baffle Adjustment Mounting Slot Selected Mounting Har dware Location Slot “A” Hole 1 Hole 2 H ole 3 Hole 4 Height (inches) 3-3/4” 4-1/4” 4-3/4” 5-1/4” Slot “B” Hole 2 H ole 3 H ole 4 Height (inches) 3-1/2” 4” 4-1/2” Custom-Cut Baffle Adjustment Figure 6-7.
27 R Section 6 ADJUSTMENT NUTS ADJUSTMENT NUTS Clutch Air Gap Adjustment Figure 6-10. This adjustment should be done e very 500 hours of operation or annually , whiche ver comes first. In cases where the machine is heavily used, airgap settings should be check ed more often.
28 R Section 6 Additional weight can be added to the front of the machine if needed. See Figure 6-11. Remov e the front belt from the machine. 1. Remov e the mounting hardware securing the 2. weight(s) to the front of the machine . Add the desired weight to the machine and secure 3.
29 R Section 6 A A B B C C D D E E F F H I J H I J G THREE MOUNTING BRACKET LOCATIONS OPERATOR CUSHION - LOW ADJUSTMENTS OPERATOR CUSHION - HIGH ADJUSTMENTS THREE OPERATOR CUSHION LOCATIONS ONE MOUNTING BRACKET LOCATION THREE OPERATOR CUSHION LOCATIONS Operator Cushion Adjustment Figure 6-12.
30 R Section 7 MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS 7.1 HOURS PROCEDURE COMMENTS BREAK-IN (FIRST 10) 8 20 40 100 200 500 X Check all hardw are for tightness X Check h ydraulic oil le vel See paragr aph 7.3 X Check belts f or proper alignment See paragr aph 6.
31 R Section 7 MAINTENANCE CHART - RECOMMENDED SER VICE INTER V ALS (CONT'D) HOURS PROCEDURE COMMENTS BREAK-IN (FIRST 10) 8 40 100 200 500 X Check hardw are for tightness X Apply grease to fittings See paragr aph 7.2 X Check h ydraulic oil le vel See paragr aph 7.
32 R Section 7 Lubrication Fitting P oints Figure 7-1. GREASE FITTING LUBRICA TION Lubricant Inter va l Lithium MP White Grease 2125 (40 Hours/W eekly) Chassis Grease (100 Hours/Bi-weekly) Chassis Gre.
33 R Section 7 B. CHANGING HYDRA ULIC OIL The h ydraulic oil should be changed after ev er y 500 hours or annually , whiche v er occurs first. The oil should also be changed if the color of the fluid has become black or milky .
34 R Section 7 B. CHANGING ENGINE CRANKCASE OIL After the first 20 hours of operation, change the engine crankcase oil and replace the oil filter . Thereafter , change the engine crankcase oil after e ver y 100 hours of operation or monthly , whichev er occurs first.
35 R Section 7 ENGINE FUEL SYSTEM 7.5 D ANGER T o av oid injur y from burns, allow the mo wer to cool bef ore remo ving the fuel tank cap and refueling. A. FILLING THE FUEL T ANK Fill the fuel tank at the beginnin g of each opera ting da y . For EP A Phase 2 (produced pr ior to 1/1/2011) models, fill to within one (1) inch belo w the filler neck.
36 R Section 7 ENGINE FUEL FIL TER Fuel Filter Figure 7-6. ENGINE AIR CLEANER 7.6 A. CLEANING AND/OR REPLA CING AIR CLEANER ELEMENT F or any air cleaner , the operating environment dictates the air cleaner ser vice per iods.
37 R Section 7 A. CHARGING THE BA TTER Y Ref er to the batter y charger’ s manual f or specific instructions. Under nor mal conditions the engine’ s alter nator will have no prob lem keeping a charge on the battery .
38 R Section 7 SGB033 Angle Blade Back Do Not Cut In X Must NOT Exceed 1/3 Blade Width X 30 Blade Sharpening Figure 7-7. Check the balance of the b lade. If the blades are out 2. of balance, vibration and premature w ear can occur . See your authorized Scag dealer f or blade balancing or special tools, if y ou choose to balance your own blades .
39 R Section 7 BOD Y AND DECK 7.10 CA UTION Do not wash an y portion of the equipment while it is hot. Do not wash the engine; use compressed air . After each use, w ash the mow er and cutter deck. 1. Use cold water and automotiv e cleaners. Do not use pressure cleaners.
40 R Section 7 NOTES.
41 R Section 8 SCA G APPRO VED A TT A CHMENTS AND A CCESSORIES. 8.1 Attachments and accessor ies manuf actured by companies other than Scag P ower Equipment are not approv ed f or use on this machine.
42 R Section 8 61V CUTTER DECK B B 47 A A 1 1 2 2 3 3 4 4 4 5 7 9 8 6 10 5 8 9 11 5 8 12 12 13 13 14 17 15 16 18 19 20 20 18 21 22 23 24 25 26 27 28 29 31 30 33 34 35 48 36 37 38 39 39 41 40 42 43 44 .
43 R Section 8 61V CUTTER DECK Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39.
44 R Section 8 SVR-61V CUTTER DECK CONTR OLS 61 61 A B C C A B D D 1 2 3 5 4 8 9 10 8 8 8 12 9 42 4 14 5 8 9 12 10 8 9 8 11 6 6 7 4 11 8 13 8 8 8 10 9 12 9 5 14 4 60 59 59 59 60 21 22 20 19 15 18 16 5.
45 R Section 8 SVR-61V CUTTER DECK CONTR OLS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 .
46 R Section 8 SVR-61V SHEET MET AL COMPONENTS B B A A C C 3 35 34 33 1 2 4 46 6 5 6 47 2 17 11 10 9 8 7 9 12 13 14 15 30 15 15 16 6 19 21 13 20 18 24 23 48 26 35 35 6 22 25 28 29 27 26 35 36 37 35 15.
47 R Section 8 SVR-61V SHEET MET AL COMPONENTS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 462240 04001-.
48 R Section 8 SVR-61V STEERING CONTR OLS 24 A A B B 12 12 13 18 17 19 20 23 24 16 15 14 15 22 11 21 25 26 29 30 27 *28 34 33 31 32 10 35 24 36 32 39 34 40 43 41 42 44 37 38 37 38 38 11 10 9 8 11 10 9.
49 R Section 8 SVR-61V STEERING CONTR OLS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 *28 29 30 484093 04020-1.
50 R Section 8 SVR-61V FUEL SYSTEM - EP A PHASE 2 (models pr oduced prior to 1/1/2011) 1 2 4 6 5 8 7 3 9 10 11 9 10 11 TO FUEL FIL TER.
51 R Section 8 SVR-61V FUEL SYSTEM - EP A PHASE 2 (models pr oduced prior to 1/1/2011) Ref. No. P art No. Description 1 483617 Fuel Hose, 1/4" ID (order b y inch) 2 48059-01 Clamp , Fuel Hose 3 462205 Fuel T ank Assembly - SVR-61V 4 483896 V alve, Fuel Shut Off 5 482571 Bushing, .
52 R Section 8 SVR-61V FUEL SYSTEM - EP A PHASE 3 (models pr oduced after to 1/1/2011) 1 2 4 6 5 8 7 3 9 10 11 TO FUEL FIL TER 9 10 23 T ank Purge A A To Engine Purge Po rt B B 12 13 14 14 13 14 14 14.
53 R Section 8 SVR-61V FUEL SYSTEM - EP A PHASE 3 (models pr oduced after to 1/1/2011) Ref. No. P art No. Description 1 483617 Fuel Hose, 1/4" ID (order b y inch) 2 48059-01 Clamp , Fuel Hose 3 462300 Fuel T ank Assembly - SVR-61V 4 483896 V alve, Fuel Shut Off 5 482571 Bushing, .
54 R Section 8 SVR-61VHYDRA ULICS AND ENGINE COMPONENTS A A B C C D D E E F G H H J J K K L L 2 3 5 3 3 3 3 3 3 5 5 5 5 5 5 3 B 6 6 5 10 9 14 8 13 11 12 4 4 7 17 18 6 54 M M 64 G F N N 7 5 3 1 15 16 1.
55 R Section 8 SVR-61V HYDRA ULICS AND ENGINE COMPONENTS Ref. No. P art No. Description Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 .
56 R Section 8 ELECTRICAL SYSTEM 20 20 1 2 3 SC AG POWER EQUIPMENT 4 5 6 7 8 9 12 10 13 14 11 17 16 18 19 20 21 16 22 23 24 25 26 27 28 15 A A.
57 R Section 8 ELECTRICAL SYSTEM Ref. No. P art No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 462240 483957 48798 48017-03 48017-04 462069 483609 483976 48.
58 R Section 8 REPLA CEMENT DECALS AND INFORMA TION PLA TES 1 2 3 4 5 6 7 8 9 10 11 H e a v y - D u ty Co m m e r c i a l 481971 __________ __________ __________ __________ __________ __________ _____.
59 R Section 8 REPLA CEMENT DECALS AND INFORMA TION PLA TES Ref. No. P art No. Description 1 483402 Decal, Warning - Belt Cov er 2 483405 Decal, Warning 3 483961 Decal, Belt Cov er 4 483201 Decal, 61V.
60 R Section 8 SVR ELECTRICAL SCHEMA TIC 20 20 PTO SWITCH KEY SWITCH ENGINE HOURMETER BRAKE INTERLOCK SWITCH CLUTCH GROUND OPERA TO R PRESENCE SWITCH 20 AMP FUSE 20 AMP FUSE NEUTRAL INTERLOCK BLUE RED.
LIMITED W ARRANTY - COMMERCIAL EQUIPMENT Any part of the Scag commercial mower manuf actured by Scag P ower Equipment and f ound, in the reasonable judgment of Scag, to be def ective in materials or w.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Scag Power Equipment SVR61V-29FX è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Scag Power Equipment SVR61V-29FX - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Scag Power Equipment SVR61V-29FX imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Scag Power Equipment SVR61V-29FX ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Scag Power Equipment SVR61V-29FX, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Scag Power Equipment SVR61V-29FX.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Scag Power Equipment SVR61V-29FX. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Scag Power Equipment SVR61V-29FX insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
