Manuale d’uso / di manutenzione del prodotto GC-STT-CS del fabbricante Scag Power Equipment
Vai alla pagina of 28
MODEL GC-STT-CS THIS MANUAL CONT AINS THE OPERA TING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSOR Y . READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSOR Y PERFORMING T O MAXIMUM EFFICIENCY .
F AILURE TO FOLLOW SAFE OPERA TING PRACTICES MA Y RESUL T IN SERIOUS INJURY . * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning.
1 1.1 INTRODUCTION This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.
2 3. When dumping the hopper into a disposal area: A . Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. B . Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper .
3 3.1 ASSEMBLY INSTRUCTIONS FOR 52" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
4 RIGHT SIDE OF 52" CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS HEX HEAD BOL T ELASTIC STOP NUTS.
5 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the hardware at this time.
6 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 18 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
7 4.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
8 RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L .
9 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 4-3, Page 8. Do not fully tighten the hardware at this time.
10 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 16 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
11 5.1 ASSEMBLY INSTRUCTIONS FOR 72" CUTTER DECKS -NOTE- Use the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access.
12 P R O P E R L Y S E R V I C E E N G I N E W I T H O I L A N D F U E L . BLOWER ASSEMBLY MOUNTING POST PIN CARRIAGE BOLTS CATCH PLATE LOCK WASHERS ELASTIC STOP NUTS AND LOCK WASHERS HEX HEAD BOL TS ELASTIC STOP NUTS GC-STT install art 3 HAIR PIN RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
13 6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 5-3, Page 12. Do not fully tighten the hardware at this time.
14 WEIGHT SUPPORT BAR BAR CLAMP ELASTIC STOP NUT WEIGHT (5x) LANYARD PIN BOLT 2002 GC-STT Install Art 3-5 17 . Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine.
15 FIGURE 5-6 Liquid Cooled Only Note: Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model.
16 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley. 4. Remove the pin holding the blower assembly to the mounting bracket on the cutter deck and remove the blower assembly.
17 Notes.
18 GC-STT BLO WER HOUSING ASSEMBL Y W A R N IN G INSTALL BEL T COVER BEFORE OPERATING M ACHINE R E A D O P E R A T O R ' S M A N U A L 390STT0200A 1 2 3 3 45 47 45 4 5 6 7 8 9 9 10 10 11 11 12 12.
19 GC-STT BLO WER HOUSING ASSEMBL Y Ref. Pa r t No . Number Description 1 04067-07 Pin, Ring 2-1/4" Long 2 481547 Lanyard, Deck Height Pin 3 04019-02 Nut, Serr .
20 GC-STT BLO WER MOUNTING COMPONENTS 1 2 3 4 5 6 6 7 8 9 10 10 11 12 13 14 15 15 19 20 21 16 17 18 390STT0203 RIGHT SIDE OF 61" CUTTER DECK SHOWN Note: Parts for 52"cutter deck may vary slightly from illustration. Some parts not shown for viewing purposes.
21 GC-STT BLO WER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482406 Belt Cov er , GC-STT - 52" 482378 B e lt C ov e r , GC-STT - 61" & 72" 2 04029-04 Wingnut, Plastic 3/8 Small 3 482300 C ap , Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461419 Adapter , Blow er GC-STT 6 04040-14 Flatwasher , 1/4-.
22 GC-STT -CS HOPPER COMPONENTS A A B B C C CSHOPPEREXPLODE2-STT 1 16 45 15 14 45 43 56 55 6 17 41 50 5 4 3 49 31 51 11 40 58 59 25 12 8 9 34 49 50 24 34 29 42 27 48 38 53 10 33 61 60 37 19 36 20 4 9 .
23 GC-STT -CS HOPPER COMPONENTS Ref. Pa r t No . Number Description 1 461627 Hopper , GC-STT -CS 2 482732 Door , GC-CS 3 461626 Sweeper Weldment, GC-CS 4 482777 Pad, Rubber 5 04090-02 P op Ri v et, 3/16 x .652 6 423834 Plate, Stiffener 7 423831 Suppor t F rame, Hopper 8 423849 Hinge Bracket, L.
24 GC-STT DECALS 481039 482275 482733 482293.
LIMITED W ARRANTY- COMMERCIAL A CCESSOR Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor.
P ART NO. 03140 PRINTED 8-2003 PRINTED IN USA © 2003 SCAG POWER EQUIPMENT DIVISION OF MET ALCRAFT OF MA YVILLE, INC www .scag.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Scag Power Equipment GC-STT-CS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Scag Power Equipment GC-STT-CS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Scag Power Equipment GC-STT-CS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Scag Power Equipment GC-STT-CS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Scag Power Equipment GC-STT-CS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Scag Power Equipment GC-STT-CS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Scag Power Equipment GC-STT-CS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Scag Power Equipment GC-STT-CS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
