Manuale d’uso / di manutenzione del prodotto 400e del fabbricante SATO
Vai alla pagina of 96
PN 9001 135A XL400e / XL410e Printers OPERATOR MANUAL.
SATO UK Limited Valley Road, Harwich Essex CO12 4RR Tel: 0 1255 240000 Fax: 01255 240111 Tech Support Hotline: 01255 252828 Email: techsupport@satouk.com www.satouk.com © Copyright 200 5 SATO UK Limited Warning: This equipment complies with the requirements in Part 15 of FCC rules for a Class A computing device.
PN 9001135A T ABLE OF CONTENTS INTRODUCTION About This Manual 1-2 General Description 1-3 Control Features 1-4 TECHNICAL DATA Physical Characteristics 2-2 Enviromental 2-2 Power 2-2 Processing 2-2 Pri.
PN 9001135A OPERATION Printer Configuration 4-2 Dip Switch Panels 4-2 Configuration Modes 4-6 Normal Mode 4-6 Test Print M ode 4-7 Advanced M ode 4-8 Default Settings Mode 4-9 Flash Mem ory Download M.
PN 9001135A MAINTENANCE Cleaning Procedures 6-2 Replacement Procedures 6-3 Fuse 6-3 Print Head 6-4 Ribbon Roller 6-5 Adjustment Procedures 6-6 Print Head Balance 6-7 Print Head Alignment 6-8 Pressure .
PN 9001135A.
SATO XL400-410e Operator Manua l PN 9001135A Page 1-1 INTRODUCTION • About This Manual • General Description • Control Features.
Unit 1: Introduction SATO XL400-410e Operator Manual PN 9001135A Page 1-2 ABOUT THIS MANUAL This manual is laid out consistent with the pr oduct discussed and provides all of the information required for general printe r configuration, operation, troubleshooting, and maintenance.
Unit 1: Introduction SATO XL400-410e Operator Manua l PN 9001135A Page 1-3 GENERAL DESCRIPTION The XL400/410 “e” series prin ters are comple te, high-performance labeling systems designed specifically for printing labels and tags.
Unit 1: Introduction SATO XL400-410e Operator Manual PN 9001135A Page 1-4 CONTROL FEATURES Figure 1-2a, Control Features BUTTONS & SWITCHES POWER T wo position on/off switch that controls power flow to the system. ST ART / ST OP T oggles the printer on/ off line.
Unit 1: Introduction SATO XL400-410e Operator Manua l PN 9001135A Page 1-5 Figure 1-2b, Control Features Figure 1-3, Connection Port s CONNECTION PORTS AC Power Input Connector permit s 1 15V , 50/60 Hz supply via supplied cord. Interface Port Connector for interface h arness.
Unit 1: Introduction SATO XL400-410e Operator Manual PN 9001135A Page 1-6.
SATO XL400-410e Operator Manua l PN 9001135A Page 2-1 TECHNICAL DAT A • Physical Charcteristics • Enviroment al •P o w e r • Processing •P r i n t • Sensing •M e d i a • Character Font.
Unit 2: Technical Data SATO XL400-410e Operator Manual PN 9001135A Page 2-2 PHYSICAL CHARACTERISTICS Width 19.6 Inches (3 02 mm) Height 1 1.50 Inches (294 mm) Depth 1 1.
Unit 2: Technical Data SATO XL400-410e Operator Manua l PN 9001135A Page 2-3 MEDIA Eye-Mark Label Dime nsions Width: 1.26 to 3. 94 Inches ( 32-100mm) Length: 1.00 to 9.45 Inches (25-2 40mm) Gap Label Dimensions Width: 1.00 to 3. 94 Inches ( 25-100mm) Length: 0.
Unit 2: Technical Data SATO XL400-410e Operator Manual PN 9001135A Page 2-4 BAR CODE CAPABILTIES Linear Bar Codes Bookland (UPC/EAN Supplement al EAN-8, EAN-13 CODABAR Code 39 Code 128 Interleaved 2 o.
SATO XL400-410e Operator Manua l PN 9001135A Page 3-1 INSTALLATION • Unp acking • Part s Identification • Printer Inst allation • Interface Selection • Accessories Inst allation.
Unit 3: Installation SATO XL400-410e Operator Manual PN 9001135A Page 3-2 UNP ACKING & P ART S IDENTIFICATION Place the shipping container upright on a solid, fl at surface.
Unit 3: Installation SATO XL400-410e Operator Manua l PN 9001135A Page 3-3 PRINTER INST ALLATION This chapter provides guidance on general p rinte r setup and installation. The following chapter provides instructions o n how to select an interface for the host to communicate with the p rinter.
Unit 3: Installation SATO XL400-410e Operator Manual PN 9001135A Page 3-4 MEDIA LOADING Perform the following steps to load media into the printer. This p rocedure covers only the physical installation of media and is app licabl e regardless of the media type.
Unit 3: Installation SATO XL400-410e Operator Manua l PN 9001135A Page 3-5 Figure 3-3b, Media Loading Figure 3-3c, Media Loading Media Supply Spindle Media Media Retaining Plate Media Hold-Down Print .
Unit 3: Installation SATO XL400-410e Operator Manual PN 9001135A Page 3-6 Figure 3-3d, Media Loading Figure 3-3e, Media Loading Media Media Ramp Cutter Assembly Set Screw Paper Guide Top Housing Cover.
Unit 3: Installation SATO XL400-410e Operator Manua l PN 9001135A Page 3-7 Figure 3-3f, Media Loading RIBBON LOADING Perform the following steps to load the printe r with ribbon. This procedure covers only the physical installation of ribbon. Refer to t he Configuration unit for setup instructions.
Unit 3: Installation SATO XL400-410e Operator Manual PN 9001135A Page 3-8 Figure 3-4a, Rib bon Loading Figure 3-4b, Ribbon Loading Power Switch Power Supply Cord Top Housing Cover Ribbon Prin t Assem .
Unit 3: Installation SATO XL400-410e Operator Manua l PN 9001135A Page 3-9 Figure 3-4c, Rib bon Loading Figure 3-4d, Ribbon Loading Ribbon Roll Ribbon Core Ribbon Unwi nd Spindle Ribbon Rewind Spi ndl.
Unit 3: Installation SATO XL400-410e Operator Man ual PN 9001135A Page 3-10 Figure 3-4e, Rib bon Loading Figure 3-4f, Ribbon Loading Ribbon Core Ribbon Print Head Latch Ribbon Top Housing Cover.
Unit 3: Installation SATO XL400-410e Operato r Manual PN 90 01135A Page 3-11 Figure 3-4g, Ribbon Loading Label/Tag Power Swi tch.
Unit 3: Installation SATO XL400-410e Operator Man ual PN 9001135A Page 3-12 INTERFACE SELECTION This chapter present s the printer interface types and the ir specifications. These specifications include detailed information to assist in the se lection of the most appropriate meth od for the printer to interface with the host.
Unit 3: Installation SATO XL400-410e Operato r Manual PN 90 01135A Page 3-13 Figure 3-5, Serial Connector Pin Asignment s RS232C SERIAL INTERFACE SIGNALS PIN DIRECTION SIGNAL DEFINITION 1 Reference FG (Frame Ground) 2 T o Host TD (T ransmit Data) - Dat a from the printer to the host computer .
Unit 3: Installation SATO XL400-410e Operator Man ual PN 9001135A Page 3-14 IEEE1284 PARALLEL INTERFACE The parallel interface is a Plu g-In, bi-directio nal, Interface Module that can be inst alled by the user . It conforms to the IEEE1284 specification.
Unit 3: Installation SATO XL400-410e Operato r Manual PN 9001135A Page 3-15 UNIVERSAL SERIAL BUS (USB) ADAPTER The Universal Serial Bus (USB) interface is a Pl ug-In Interface Module that can be inst alled by the user .
Unit 3: Installation SATO XL400-410e Operator Man ual PN 9001135A Page 3-16 RECEIVE BUFFER The data stream is received fro m the host to the printer one job at a time. This allows the software pro gram to maintain control of the job print queue so that it can move a high priority job in front of ones of lesser importance.
Unit 3: Installation SATO XL400-410e Operato r Manual PN 9001135A Page 3-17 ACCESSORIES INST ALLATION In most instances, the print er is ordered with the desired accessories pre-installe d. However, changes in printing conditions or re quirements does warrant upgra des from time to time.
Unit 3: Installation SATO XL400-410e Operator Man ual PN 9001135A Page 3-18 STACKER UNIT The XL Stacker Unit collects and stacks tags as they are printed and cut. Installation of the included alignment plate ensures proper spacing and alignment of the stacker with the printer.
SATO XL400-410e Operator Manua l PN 9001135A Page 4-1 OPERATION • Printer Configuration • Configuration Modes • Operational Adjustment s •P r i n t i n g.
Unit 4: Operation SATO XL400-410e Operator Manual PN 9001135A Page 4-2 PRINTER CONFIGURATION The printer may be configured for specific jobs via the operator panel located on the right side of the printer and the interface panel co mprised of three dip switch complexes and four potentiometers located within the printer’s interior .
Unit 4: Operation SATO XL400-410e Operator Manua l PN 9001135A Page 4-3 DSW1 DEFAULT SETTINGS 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 O F FO F FO F FO F FO F FO F FO F FO F F DSW1 CONFIGURA TION 1-1 Data BIt .
Unit 4: Operation SATO XL400-410e Operator Manual PN 9001135A Page 4-4 DSW2 DEFAULT SETTINGS 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 O F FO F FO F FO F FO F FO F FO F FO F F DSW2 CONFIGURATION DSW2 FUNCTION S.
Unit 4: Operation SATO XL400-410e Operator Manua l PN 9001135A Page 4-5 DSW3 DEFAULT SETTINGS 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 O F FO F FO F FO F FO F FO F FO F FO F F DSW3 CONFIGURATION DSW1 FUNCTION .
Unit 4: Operation SATO XL400-410e Operator Manual PN 9001135A Page 4-6 CONFIGURATION MODES With exception of the Power switch located on the back side of th e printer , all of the following configurat.
Unit 4: Operation SATO XL400-410e Operator Manua l PN 9001135A Page 4-7 TEST PRINT MODE This mode allows the operator t o print test labels for troubleshooting and for verif ication of configuration settings. Figure 4-2, T est Print Mode TEST PRINT MODE CONFIGURATION FEED + POWER Printer beeps FEED To select.
Unit 4: Operation SATO XL400-410e Operator Manual PN 9001135A Page 4-8 ADVANCED MODE The Advanced Mode is provide d to make basic printer operational adjustme nts. T ypically , once these adjustment s or settings have been made, t hey will not require additio nal address unless a new job is downloaded.
Unit 4: Operation SATO XL400-410e Operator Manua l PN 9001135A Page 4-9 DEFAULT SETTINGS MODE When the sequences have been completed, the printer automatically returns to it s default gap or eye-mark settings. The default settings are t hose programmed se ttings of the factory prior to delivery .
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-10 FLASH MEMORY DOWNLOAD MODE A Flash ROM internally stores and deletes font data and custom de signed character data. T he storage capacity for cu stom characters is 95 for each type of 16 x 16, 22 x 22, and 24 x 24 dot s.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-11 Figure 4-5, Flash Memory Downlo ad Mode STORAGE OF CUSTOM DESIGNED CHARACTER ST ATUS DESCRIPTION ACSII HEX TRANSFER S torage Re.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-12 USER DOWNLOAD MODE This download feature allows the operator to download print jobs to the printer . When downloading is complet e, the LCD screen will return to the origin al display af ter three seconds.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-13 HEX DUMP MODE The contents of the print buf fer and the data received before it is placed into the print buf fer may be examined through the use of the Hex Dump Mode.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-14 CARD MODE This configuration mode is used for configu ring the Flash ROM and/or PCMCIA interface cards. The following t able identifies the menu s of the Card Mode and their purpose.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-15 NON-STANDARD CLEAR MODE Returns non stan dard protocol code to the default value. The default values are STX (7B), ETX (7D), ESC (5E), ENQ (40), NUL (7E), CAN (21), OFFLINE (5D).
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-16 SERVICE MODE Allows the programming of various dimensional settings and the language used. Refer to the table below for an explaination of each menu en countered. The following flow chart provides configuration sequence.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-17 Figure 4-10b, Service Mode - Sensor Level SERVICE MODE DIPSW2-4 ON->OFF DSW2-4 = ON START/STOP + FEED + POWER DSW2-4 = OFF Print er beeps SERVICE MODE TEST PRINT FEED START/STOP SERVICE MODE SENSOR LEVE L GAP [ x.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-18 Figure 4-10c, Service Mode - Pitch Offset SERVICE MODE DIPSW2-4 ON->OFF DSW2-4 = ON START/STOP + FEED + POWER DSW2-4 = OFF Printer beeps SERVICE MODE TEST PRINT FEED START/ST OP SERVICE MODE PITCH OFFSET PITCH OFFSET CENTER HOLE +00 START/STOP to sc roll .
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-19 Figure 4-10d, Service Mode - Cut Offse t SERVICE M ODE DIPSW2-4 ON->OFF DSW2-4 = ON START/ST OP + FEED + POWE R DSW2-4 = OFF Printer beeps SERVICE M ODE TEST PRINT FEED START/ST OP SERVIC E MODE PITCH OFFSET CUT OFFSET CENTER HOLE +00 START/STOP to scroll.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-20 Figure 4-10e, Service Mode - Backfeed Offset SERVICE MODE DIPSW2-4 ON->OFF DSW2-4 = ON START/STOP + FEED + POWER DSW2-4 = OFF Print er beeps SERVICE MODE TEST PRIN T FEED START/STOP SERVICE MODE PITCH OFFSET BACKFEED OFFSET CENTER HOLE +00 START/STOP to scroll.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-21 Figure 4-10f, Service Mode - Counter Display SERVICE MODE DIPSW2-4 ON->OFF DSW2-4 = ON START/STOP + FEED + POWER DSW2-4 = OFF Printer beeps SERVICE MODE TEST PRINT FEED START/STOP SERVICE MODE PITCH OFFSET COUNTER LIFE X .
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-22 NORMAL MODE MENU DESCRIPTION NORMAL MODE Basic print functions. ONLINE 000000 00000000 Receives data and can issue a label. Displays the count down number an d the count-up number in the lo wer region on the LCD.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-23 ADVANCED MODE MENU DESCRIPTION ADV ANCED MODE Menu allows configuration of printer features that typically do not require change . CHARACTER PITCH The PROP option a llows pr oportional pitch and the F IXED option is without.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-24 CARD MODE MENU DESCRIPTION CARD MODE Menu allows config uration of the memory card. MEM SELECT(CC1) CARD MEMO RY Establishes the media of the first drive . The default value is on the card.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-25 SERVICE MODE MENU DESCRIPTION SERVICE MODE Menu allows configurat ion media type . COUNTER CLEAR NON E Selects the coun ter to clear . The options are None, All, Print Head, Cutter , and Dispenser .
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-26 OPERATIONAL ADJUS TMENTS These operational adjustment s are for fine tuning the printer as necessary following the configuration process and are confined to the three potentiometers located on t he adjustment panel in addition to the operator p anel.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-27 Figure 4-1 1, Ad justment Panel VR4 VR3 VR2 VR1 DSW 1 DSW 2 DSW 3 DARKNESS CUT POSITION PRINT POSITION DISPLAY VR1 Reference La.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-28 CUTTER SENSOR POSITIONING The cutter assembly has dual adjust able sensors and is designed to permit lateral movement of the sensor assembly to acco mdate multiple medi a types.
Unit 4: Operation SATO XL400-410e Operato r Manual PN 9001135A Page 4-29 OPERATOR P ANEL The operator p anel may be used at two dif feren t angles. The norma l angle is flush with the surface of the printer . Pressing against the upper portion of the p anel causes it to tilt backwards to allow better viewing under cert ain situations.
Unit 4: Operation SATO XL400-410e Operator Man ual PN 9001135A Page 4-30 PRINTING At this point, both the printer and the operator shou ld be ready to print labels or t ags.
SATO XL400-410e Operator Manua l PN 9001135A Page 5-1 TROUBLESHOOTING • Error Signals • Printer T roubleshooting • InterfaceT roubleshooting • Performance T esting • T est Print T roubleshoo.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manual PN 9001135A Page 5-2 ERROR SIGNALS This unit coorelates the three type s of error signals with probabl e causes and problem resolution. Three types error signals are: LED, LCD Message, and an audible beep.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manua l PN 9001135A Page 5-3 PRINTER TROUBLESHOOTING TROUBLESHOOTING T ABLE IMAGE V OIDS Damaged print head. Replace print head. Damaged electronics. Replace circuit board. Damaged or worn platen roller .
Unit 5: Trou bleshooting SATO XL400-410e Operator Manual PN 9001135A Page 5-4 NO PRINTED IMAGE Print head is disconnected. Ensure print head wiring harness is connected on each end. No voltage outp ut. T est power supply and replace as necessary . Damaged print head.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manua l PN 9001135A Page 5-5 INTERFACE TROUBLESHOOTING This unit provides a checklist for the various inte rface types. Locate the chec klist relative to the interface used and perform each of the troub les hooting tasks until the problem has been isolated.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manual PN 9001135A Page 5-6 LAN EHTERNET INTERFACE CHK TROUBLESHOOTING STEP Ensure the interface has been correctly configure d. W ait two minutes and run self-test to ver ify . If a test label does not print, there ma y be a hardware proble m.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manua l PN 9001135A Page 5-7 PERFORMANCE TESTING This unit explains how to troubleshoot circuitr y and adjust sensors using a multimeter. These activities may be performed with or without te st module assistance in conjunction with the multimeter.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manual PN 9001135A Page 5-8 MULTIMETER ALONE Testing of circuitry an d sensor adjustment may be performed by using a multimeter witho ut the assistance of the test module. To perform this ta sk the multimeter probes must be attached to the correct connector pins of the test connector.
Unit 5: Trou bleshooting SATO XL400-410e Operator Manua l PN 9001135A Page 5-9 TEST PRINT TROUBLESHOOTING Chapter provides instruction on special pr inting to identify and resolve specific print problems. HEX DUMP Allows the operator to determine if there were problems in the downloading of data.
Unit 5: Trou bleshooting SATO XL400-410e Operator Man ual PN 9001135A Page 5-10 TEST LABEL PRINTING The test label is designed to assist in the iden tification of print problems.
Unit 5: Trou bleshooting SATO XL400-410e Operato r Manual PN 9001135A Page 5-11 Figure 5-5, Sample T est Label D S W 3 D S W 2 D S W 1 N O N E SAMPLE TEST LABEL Label Contents W ill Vary Depending on Test Label Typ e. Compare this sc ale on each side to e nsure t he pri nt is evenly spac ed hori zontall y.
Unit 5: Trou bleshooting SATO XL400-410e Operator Man ual PN 9001135A Page 5-12 SENSOR LOCATIONS This chapter provides a diagram identifying the locations of the printer’s various sensors.
SATO XL400-410e Operator Manua l PN 9001135A Page 6-1 MAINTENANCE • Cleaning Procedures • Replacement Procedures • Adjustment Procedures.
Unit 6: Maintenance SATO XL400-410e Operator Manual PN 9001135A Page 6-2 CLEANING PROCEDURES Cleaning of the printer is a necessary maintenance activity to ensure print quality and long prin ter life. There are two basic types of cleaning involved; the r emoval of loose debris and the remova l of residue.
Unit 6: Maintenance SATO XL400-410e Operator Manua l PN 9001135A Page 6-3 REPLACEMENT PROCEDURES The printer contains replaceable compone nts and sub-assemblies. This chapter contains step- by-step instructions for the removal and replacemen t of those primary components and sub- assemblies that are subject to wear o r damage.
Unit 6: Maintenance SATO XL400-410e Operator Manual PN 9001135A Page 6-4 PRINT HEAD REPLACEMENT If the print head becomes damaged or wears out, it can be easily replaecd using a screwdriver. Critical adjustments are not required because the print head is a subassembly mou nted to a permanent, factory adjusted mechanism.
Unit 6: Maintenance SATO XL400-410e Operator Manua l PN 9001135A Page 6-5 RIBBON ROLLER REPLACEMENT The ribbon roller is a high wear component due to th e ribbon medium treading on its surfa ce. The ribbon roller is the only roller approved for repl acement by the operator .
Unit 6: Maintenance SATO XL400-410e Operator Manual PN 9001135A Page 6-6 ADJUSTMENT PROCEDURES To maintain optimum performance and print qua lity, periodically mechanical adjustments will have to be made. These adjustme nts are typically required following the re placment of a component.
Unit 6: Maintenance SATO XL400-410e Operator Manua l PN 9001135A Page 6-7 PRINT HEAD BALANCE ADJUSTMENT If the print head balance is ou t of adjustment, the printed image will be darker on side of the label than the other and the media stock will be proned to want to travel in the direction of least resistance.
Unit 6: Maintenance SATO XL400-410e Operator Manual PN 9001135A Page 6-8 PRINT HEAD ALIGNMENT Print head position has a direct impact on print quality. An improperly aligned print head will cause the print to be inconsist ent across the label. The following pro cedure will provide guidance on print head alignmen t.
Unit 6: Maintenance SATO XL400-410e Operator Manua l PN 9001135A Page 6-9 PRESSURE ROLLER ALIGNMENT The pressure roller works in conjunction with the feed roller , sandwiching the loaded media between the two. It is the drive-coupled feed roller that a dvances the media forward to the platen roller.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-10 PRESSURE ROLLER BALANCE The pressure roller works in conjunction with the feed roll er, sandwiching the loaded media between the two. It is the drive-coupled feed roller that advances the media forward to the plat en roller.
Unit 6: Maintenance SATO XL400-410e Operato r Manual PN 9001135A Page 6-11 RIBBON GUIDE ADJUSTMENT If the print ribbon is no t spread smoothly over the print head when it makes contact with t he media, print voids will occur at th e point of the ribbon fold.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-12 RIBBON SPINDLE TENSIONING The printer has two ribbon spindles; one to supply ri bbon medium from the rear of the printer past the print head to the spindle closest to the front for the purpo se of rewinding the used medium.
Unit 6: Maintenance SATO XL400-410e Operato r Manual PN 9001135A Page 6-13 PITCH SENSOR ADJUSTMENT (LABEL GAP & CENTER HOLE MEDIA) This sensor adjustment re gulates penetrating ability fo r media referencing.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-14 PITCH SENSOR ADJUSTMENT (EYE-MARK MEDIA) This sensor adju stment regulates penetrating ability fo r media referencing.
Unit 6: Maintenance SATO XL400-410e Operato r Manual PN 9001135A Page 6-15 Figure 6-1 1, T est Module & Sensor Potentiometers Figure 6-12, T est Connector Connect ground probe here 0 1 2 3 4 5 6 7.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-16 PITCH SENSOR ADJUSTMENT (R-CORNER MEDIA) This sensor adju stment regulates penetrating ability fo r media referencing.
Unit 6: Maintenance SATO XL400-410e Operato r Manual PN 9001135A Page 6-17 PITCH SENSOR ADJUSTMEN T (SIDE HOLE MEDIA) This sensor adjustment re gulates penetrating ability fo r media referencing.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-18 JUMP HOLE SENSOR ADJUSTMENT This sensor adju stment regulates penetrating ability fo r media referencing.
Unit 6: Maintenance SATO XL400-410e Operato r Manual PN 9001135A Page 6-19 RIBBON SENSOR ADJUSTMENT This sensor adjustment regulates penet rating abili ty for ribbon feed. Pene tration modification is performed via a potentiometer that is part of the potentiometer complex located behind the access panel on the left side of the print er.
Unit 6: Maintenance SATO XL400-410e Operator Man ual PN 9001135A Page 6-20 CUTTER SENSOR ADJUSTMENT This sensor adjustment regulates penetra ting ability for the cutter sensor. Penetration modification is performed via a potentiometer that is part of the cutte r assembly.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il SATO 400e è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del SATO 400e - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso SATO 400e imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul SATO 400e ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il SATO 400e, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del SATO 400e.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il SATO 400e. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo SATO 400e insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
