Manuale d’uso / di manutenzione del prodotto SRP-350 del fabbricante Samsung
Vai alla pagina of 30
Operator’s Manual All specifications are subjected to change without notice http://www.samsungminiprinters.com SRP-350 Ver.2 RECEIPT PRINTER 1 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.
2 Violating following instructions can cause slight wound or damage the appliance. Keep the desiccant out of children’s reach. If not, they may eat it. Install the printer on the stable surface. If the printer falls down, it can be broken and you can hurt yourself.
4 Table of Contents CHAPTER 1. SETTING UP THE PRINTER ..................................... 5 1-1. U NPACKING .............................................................................. 5 1-2. C ONNECTING THE C ABLES ...............................
6 1-2. Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector pa nel on the back of the printer, which is shown below : Notes : Before connecting any of the cables, make sure that both the printer and the host are turned off.
8 1-5. Connecting the Power Supply CAUTIONS: When connecting or di sconnecting th e power supply from the pri nter, make sure th at the power supply is not plugged into an elec trical outlet .
10 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of pa per, as shown. Then close the cover. 7. Tear off the paper as shown. Notes : When closing the cover, press the center of printer cover firmly to prevent p a p er miss-loadin g 11 1-7.
12 1-8. Using the Printer Control Panel Button The button can be disabl ed by the ESC c 5 command. Press the FEED button once to advance pap e r one line. You can also hold down the FEED button to feed paper continuously. Panel lights POWER The POWER light is on whenever the printer is on.
14 Parallel/USB Interface Specification Dip Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Auto Line Feed Always Enabled Always Disabled OFF 2 Reserved - - OFF 3 Reserved - - OFF 4 Reserved - - O.
16 Chapter 3. The self test The self-test checks whether the printer has any problem s. If the printer does not function properly, contact your dealer. Th e self-test checks the following; 1. Make sure paper roll has been i nstalled properly . 2. Turn on the power while holdin g down the FEED button.
18 Page 2 ( PC850 : Multilingual ) 19 Page 3 ( PC860 : Portuguese ).
20 Page 4 ( PC 863 : Canadian - French ) 21 Page 5 ( PC 865 : Nordic ).
22 Page 19 ( PC 858 : Euro ) 23 Page 255 ( Space Page ).
24 International Character Set 25 Chapter 5. Control Commands List C o n t r o l c o d e s Hexadecimal C o d e s Function <HT> 09 Horizontal tab <LF> 0A Print and line feed <FF> 0 C .
26 Control codes Hexadecimal c o d e s Function <ESC> c 3 n 1B 63 33 n Select paper sensor to output pap er end signals <ESC> c 4 n 1B 63 34 n Select paper sensor to stop p rinting <ESC.
28 CAN [Name] [Format] [Description] Cancel print data i n page mode. ASCII CAN H e x 1 8 Decimal 24 In page mode, deletes all the print data in the current printabl e area. DLE EOT n [Name] [Format] [Range] [Description] Real-time status transmission.
30 ESC FF [Name] [Format] [Description] Print data i n page mode. A S C I I E S C F F H e x 1 B 0 C D e c i m a l 2 7 1 2 In page mode, prints all buffered data in th e printing area coll ectively. ESC SP n [Name] [Format] [Range] [Description] Set right-side character spacing.
32 ESC * m nL nH d1…dk [Name] [Format] [Range] [Description] Select bit-i mage mode. A S C I I E S C * m n L n H d 1 … d k H e x 1 B 2 A m n L n H d 1 … d k D e c i m a l 2 7 4 2 m n L n H d 1 .
34 ESC D n1… nk NUL [Name] [Format] [Range] [Description] Set horizontal tab positions. A S C I I E S C D n 1 … n k N U L H e x 1 B 4 4 n 1 … n k 0 0 D e c i m a l 2 7 6 8 n 1 … n k 0 1 ≤ n ≤ 255 0 ≤ k ≤ 32 Sets horizontal tab positions.
36 ESC T n [Name] [Format] [Range] [Description] [Default] Select print di rection in page mode. A S C I I E S C T n H e x 1 B 5 4 n D e c i m a l 2 7 8 4 n 0 ≤ n ≤ 3 48 ≤ n ≤ 51 Selects the pri nt direction and s tarting posit ion in page mode.
38 ESC c 4 n [Name] [Format] [Range] [Description] Select paper sensor(s) to stop printing. A S C I I E S C c 4 n H e x 1 B 6 3 3 4 n D e c i m a l 2 7 9 9 5 2 n 0 ≤ nL ≤ 255 Selects the paper sen.
40 FS q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n [Name] [Format] [Range] [Description] Defined NV bit i mage. A S C I I F S q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n H e x 1 C 7 1 n.
42 GS B n [Name] [Format] [Range] [Description] Turn white/black reverse pri nting mode on/off. A S C I I G S B n H e x 1 D 4 2 n D e c i m a l 2 9 6 6 n 0 ≤ n ≤ 255 Turns on or off whit e/black reverse print ing mode. * When the LSB is 0, white/black re verse pri nting mode is turned o ff.
44 GS W nL nH [Name] [Format] [Range] [Description] Set printing area width. A S C I I G S W n L n H H e x 1 D 5 7 n L n H D e c i m a l 2 9 8 7 n L n H 0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255 Sets the printing area width to the area specified by nL and nH.
46 First byte (printer information) Bit Off/On Hex Decimal Status for ASB 0 Off 00 0 Not used. Fixed to Off. 1 Off 00 0 Not used. Fixed to Off. Off 00 0 Drawer kick-out connector pin 3 is LOW. 2 On 04 4 Drawer kick-out connector pin 3 is HIGH. Off 00 0 Onl ine.
48 ① GS k m d1…dk NUL , ② GS k m n d1…dn [Name] [Format] [Range] [Description] Print bar code. ① A S C I I G S k m d 1 … d k N U L H e x 1 D 6 B m d 1 … d k 0 0 Decimal 29 107 m d1…dk .
50 APPENDIX A. Star Mode Command Summary Control codes Hexadecimal codes Function <ESC> ”R” n 1B 52 n Select international character set <ESC> <GS> t n 1B 1D 74n Select character.
52 Control codes Hexadecimal codes Function <FS> 1C Co ntrol peripheral device #1 immediately. <EM> 19 Control peripheral device #2 immediately <SUB> 1A Co ntrol peripheral device #2 immediately <ESC> “d” n 1B 64 n Partial-cut com mand to the auto cutter.
54 RS-232C Cable Connection RS-485 Cable Connection 55 Interface Connector Serial Interface (RS-232) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 TxD Output Transmit Data 3 RxD Input R.
56 Parallel Interface (IEEE-1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1 4.
58 D. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72.192 ± 0.2mm Paper width 79 ~ 80 mm Characters per line (default) 42 (Font A) 56 (Font B) Printing speed 35.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Samsung SRP-350 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Samsung SRP-350 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Samsung SRP-350 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Samsung SRP-350 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Samsung SRP-350, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Samsung SRP-350.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Samsung SRP-350. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Samsung SRP-350 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
