Manuale d’uso / di manutenzione del prodotto RF-502 del fabbricante Auto Page
Vai alla pagina of 18
RF - 502 OPERATION INSTRUCTIONS.
Congratulations on your purchase of the RF - 502 vehicle security system. AutoPage, Inc. is one of the companies with the longest history and experience in vehicle security in the United States and a wh olly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
RF - 502 1 RF - 502 OPERATION I NSTRUCTIONS A. REMOTE CONTROL TRANSMITTER OPERATION The new remote control transmitter (XT - 54) included with the RF - 502 offers the code rolling feature which will prevent illegal use of a code - grabber with an attempt to record the code of your transmitter.
RF - 502 2 particular operation. The sequence must be repeated each time if it is desired to cancel the arm/disarm chirp sound. 3. PANIC FUNCTION The RF - 502 remote control may be used as a remote panic switch to trigger the siren in cases of emergency.
RF - 502 3 To replace the battery, carefully remove the case screw located at the end of the remote where the key ring attaches to the case. Use a small blade Phillips screwdriver.
RF - 502 4 D. VALET/OVERRIDE SWITCH NOTE : Both VALET and OVERRIDE functions are performed from the same switch. 1. OVERRIDE FUNCTION The OVERRIDE FUNCTION may be used if the RF - 502 remote is lost or inoperative. To operate the OVERRIDE FUNCTION, enter the vehicle (siren will sound); switch the vehicle ignition to ON.
RF - 502 5 E. PASSIVE/MANUAL ARMING OPERATION (Optional at installation) Passive/Manual operations can be selectable if an optional toggle switch is installed. Consult your installing dealer. 1. PASSIVE ARMING If you choose the PASSIVE (aut omatic) mode, the system must be operated as below.
RF - 502 6 Approach the vehicle and press the ON/OFF remote transmitter button. The siren will chirp 2 times and the lights will flash to indicate the RF - 502 is disarmed.
RF - 502 7 1. Open any door or other protected opening. The siren will sound instantly, and the lights will flash. 2. If the pre - warning feature is activated, the RF - 502’s SIS - 5 impact sensor will respond to a light shock with a chirp sound, and trigger the alarm when a heavier shock is detected.
RF - 502 8 4. Turn the igniti on switch "ON/OFF", "ON/OFF". The siren will chirp one (1) time. You are now in the programming mode. 5. Press the ON/OFF button on one of the remote transmitters until the alarm siren responds with a confirming chirp.
RF - 502 9 Enter the programming mode on vehicle #1 and push the ON/OFF button on the tran smitter for Vehicle #1. The alarm siren will respond with a confirming chirp. Within five (5) seconds , push the AUX button on the transmitter for Vehicle #2. The alarm siren will respond with a confirming chirp.
RF - 502 10 AUTOPAGE ALARM ACCESSORIES AP - 4000DX Paging System Vehicle secu rity paging was originated by AutoPage over 18 years ago. The AP4000DX is our latest version providing a full four watts of output power to signal a handsome belt - clip paging receiver indicating your RF - 502 has been triggered, even if you cannot hear the siren.
RF - 502 11 sensors, the SIS - 10 has a LED and potentiometer for easy sensitivity adjustment. MSEN - KIT The MSEN - KIT includes two pre - wired Micro Resonance Sensors and a special triggering amplifier.
12 LIMITED LIFETIME WARRANTY PROVISIONS (U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
RF - 502 13 7 AutoPage shall not be liable, under the foregoi ng WARRANTIES or otherwise, for: Any personal injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resul.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
13 DATE SERVICE COMPLETED.
1815 W. 205th St. #101 Torrance, CA 90501 310 - 618 - 2002.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Auto Page RF-502 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Auto Page RF-502 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Auto Page RF-502 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Auto Page RF-502 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Auto Page RF-502, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Auto Page RF-502.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Auto Page RF-502. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Auto Page RF-502 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
