Manuale d’uso / di manutenzione del prodotto RF-302 del fabbricante Auto Page
Vai alla pagina of 20
RF - 302 OPERATION INSTRUCTIONS.
Congratulations on your purchase of the RF - 302 vehicle security system. AutoPage, Inc. is one of the companies with the longest history and experience in vehicle security in the United States and a wh olly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
RF - 302 1 RF - 302 OPERATION I NSTRUCTIONS A. REMOTE CONTROL TRANSMITTER OPERATION 1. ARM/DISARM TO ARM THE RF - 302 Press the ON/OFF button once to arm. The siren will chirp one (1) time, the lights will flash, and all doors will lock. (*) TO DISARM THE RF - 302 Press the ON/OFF button once to disarm.
RF - 302 2 3. PANIC FUNCTION The RF - 302 remote control may be used as a remote panic switch to trigger the siren in cases of emergency. To activate the PANIC FUNCTION press and hold the ON/OFF button on the remote transmitter for a minimum of 3 seconds.
RF - 302 3 To replace the battery, carefully remove the case screw located at the end of the remote where the key ring attaches to the case. Use a small blade Phillips screwdriver.
RF - 302 4 NOTE : Both VALET and OVERRIDE functions are performed from the same switch. 1. OVERRIDE FUNCTION The OVERRIDE FUNCTION may be used if the RF - 302 remote is lost or inoperative. To operate the OVERRIDE FUNCTION, enter the vehicle (siren will sound); switch the vehicle ignition to ON.
RF - 302 5 1. PASSIVE ARMING If you choose the PASSIVE (automatic) mode, the system must be operated as below. 1. Switch OFF vehicle ignition, exit vehicle, and be sure all protected openings are closed. 2. The LED STATUS INDICATOR will begin fast flashing and the passive arming timer will begin counting down.
RF - 302 6 Approach the vehicle and press the ON/OFF remote transmitter button. The siren will chirp 2 times and the lights will flash to indicate the RF - 302 is disarmed.
RF - 302 7 1. Open any door or other protected opening. The siren will sound instantly, and the lights will flash. 2. If optional sensors have been installed, arm the RF - 302 and test according to the directions of the particular sensor installed.
RF - 302 8 4. Turn the ignition switch "ON/OFF", "ON/OFF". The siren w ill chirp one (1) time. You are now in the programming mode. 5. Press the ON/OFF button on one of the remote transmitters until the alarm siren responds with a confirming chirp.
RF - 302 9 Enter the programming mode on vehicle #1 and push the ON/OFF button on the transmitter for Ve hicle #1. The alarm siren will respond with a confirming chirp. Within five (5) seconds , push the AUX. button on the transmitter for Vehicle #2. The alarm siren will respond with a confirming chirp.
RF - 302 10 AUX. BUTTON ON/OFF BUTTON BOTH BUTTONS TRANSMITTER #3 AUX. BUTTON BOTH BUTTONS ON/OFF BUTTON BOTH BUTTONS AUX. BUTTON ON/OFF BUTTON.
RF - 302 11 AUTOPAGE ALARM ACCESSORIES AP - 4000DX Paging System Vehicle s ecurity paging was originated by AutoPage over 18 years ago. The AP4000DX is our latest version providing a full four watts of output power to signal a handsome belt - clip paging receiver indicating your RF - 302 has been triggered, even if you cannot hear the siren.
RF - 302 12 sensors, the SIS - 10 has a LED and potentiometer for easy sensitivity adjustment. MSEN - KIT The MSEN - KIT includes two pre - wired Micro Resonance Sensors and a special triggering amplifier.
12 LIMITED LIFETIME WARRANTY PROVISIONS (U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
RF - 302 13 LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 7 AutoPage shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any p ersonal injury of an.
.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
13 DATE SERVICE COMPLETED.
1815 W. 205th St. #101 Torrance, CA 90501 310 - 618 - 2002.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Auto Page RF-302 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Auto Page RF-302 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Auto Page RF-302 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Auto Page RF-302 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Auto Page RF-302, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Auto Page RF-302.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Auto Page RF-302. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Auto Page RF-302 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
