Manuale d’uso / di manutenzione del prodotto Prestige 128-8115 del fabbricante Audiovox
Vai alla pagina of 20
128-81 15 1 of 19 Page 1 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text.
128-81 15 2 of 19 Page 2 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, t.
128-81 15 3 of 19 Page 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 C.
128-81 15 4 of 19 Page 4 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chi.
128-81 15 5 of 19 Page 5 This Remote S tart System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
128-81 15 6 of 19 Page 6 IMPORT ANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INT O THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE.
128-81 15 7 of 19 Page 7 SEE NEUTRAL S T ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch.
128-81 15 8 of 19 Page 8 Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON&qu.
128-81 15 9 of 19 Page 9 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.
128-81 15 10 of 19 Page 10 the applications described below , a relay will be required. The Light Blue wire can be used to accommodate the following situations: A.
128-81 15 11 of 19 Page 11 cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a single coil unit for each cylinder , it may be necessary to connect this wire to more than one cylinder for proper tach reference.
128-81 15 12 of 19 Page 12 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows sof tware selections to control the way in which this output oper- ates, see remote start feature # 10 for setting this output.
128-81 15 13 of 19 Page 13 columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylinder number which appears in any of the circles. 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack.
128-81 15 14 of 19 Page 14 T o test the integrity of the Neutral S tart Safety Circuit: 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. T emporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch.
128-81 15 15 of 19 Page 15 prevent the vehicle with a Mechanical Neutral S t art Switch from starting in gear . AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
128-81 15 16 of 19 Page 16 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground.
128-81 15 17 of 19 Page 17 COMPLETING THE INST ALLA TION: After you have confirmed the operation of the Audiovox Remote S tart unit and tested all the safety features of the system: 1. If you have not done so already , place the red rubber handle cover over the handle of the control switch for ease of identification.
128-81 15 18 of 19 Page 18 THIS PAGE LEFT BLANK INTENTIONALLY.
128-81 15 19 of 19 Page 19.
128-81 15 20 of 19 Page 20 © 2007 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-81 15.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Audiovox Prestige 128-8115 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Audiovox Prestige 128-8115 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Audiovox Prestige 128-8115 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Audiovox Prestige 128-8115 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Audiovox Prestige 128-8115, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Audiovox Prestige 128-8115.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Audiovox Prestige 128-8115. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Audiovox Prestige 128-8115 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
