Manuale d’uso / di manutenzione del prodotto 2075r del fabbricante Ryobi
Vai alla pagina of 20
MODEL 2075r GAS TRIMMER OPERA TOR’S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA IMPORT ANT MANUAL DO NOT THROW AW A Y.
INTRODUCTION 2 T ABLE OF CONTENTS THANK YOU Thank you for purchasing this quality pr oduct. This modern outdoor power tool is designed to provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to- understand operating instructions.
3 SP ARK ARRESTOR CALIFORNIA EMISSION REGULA TIONS SAFETY WARNINGS The engine of your lawn and garden car e product meets the 1995 to 1998 California emissions regulations. These units ar e identified by the label on the engine of your product. A typical identification label is shown.
WHILE OPERA TING • W ear safety glasses or goggles and ear/hearing protection at all times when operating this unit. Always wear a face or dust mask if the operation is dusty . • Dress pr operly . Do not operate this unit when barefoot or wearing open sandals.
SAFETY WARNINGS 5 • Keep all bystanders, especially children and pets, at least 30 feet (9.1 m) away from the unit during operation. • Do not operate the engine faster than the speed necessary to cut, trim or edge. Do not run the engine at high speed when not cutting.
6 • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate unit as a trimmer without string guard in place. Keep away fr om rotating cutter . • IGNITION SWITCH ON / ST ART / RUN • IGNITION SWITCH OFF or STOP • HOT SURF ACE WARNING Do not touch a hot muffler , gear box or cylinder .
ASSEMBL Y INSTRUCTIONS 7 INST ALLING AND ADJUSTING THE LOOP HANDLE If the loop handle is not assembled on this model, use the following instructions: 1. Place the loop handle and bottom handle clamp on the boom shaft (Fig. 1). 2. Install, one at a time , the four (4) screws and four (4) hex nuts with a Phillips screwdriver .
8 OIL AND FUEL INFORMA TION Old or improperly mixed fuel ar e usually the main reasons for the unit not running properly . Be sure to use fr esh, clean fuel and follow the instructions carefully for the pr oper fuel/oil mixture. NOTE: Alcohol-blended fuel absorbs moisture (water).
9 OPERA TING INSTRUCTIONS Fig. 6 1. MIX OIL WITH GAS AND FILL FUEL T ANK WITH FUEL/OIL MIXTURE per instructions on page 8. 2. Put the IGNITION SWITCH IN THE “ ON ” POSITION (Fig. 5). 3. FULL Y PRESS AND RELEASE THE PRIMER BULB 5 TO 7 TIMES. FUEL SHOULD BE VISIBLE IN THE BULB (Fig.
10 OPERA TING INSTRUCTIONS OPERA TING THE CLICK-LINK SYSTEM This unit is equipped with a Click-Link ® System, which enables optional attachments to be installed on the unit. The optional attachments are: Blower/V acuum. . . . . . . . . . . . . . . . .
11 OPERA TING INSTRUCTIONS CAUTION: Do not remove or alter the line cutting blade assembly . Excessive line length will cause clutch to overheat and may result in serious personal injury . Fig. 12 Each time the head is bumped, about 1 inch (25.4 mm) of trimming line is released.
MAINTENANCE AND REP AIR INSTRUCTIONS 12 Fig. 15 3. Insert the line into the locking hole (Fig. 15) no more than 1/2 inch (12.7 mm). Do not push the line too far into the inner reel. A small loop is formed when the line is inserted correctly (Fig. 15).
MAINTENANCE AND REP AIR INSTRUCTIONS 13 Fig. 18 Fig. 19 Fig. 17 5. Repeat the procedur e with the second eyelet and use the same amount of line as specified in Step 2. 6. Wind the inner reel counter clockwise until approximately four (4) inches of line r emains outside of the eyelets in the outer spool (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 14 3. W ash the filter in detergent and water (Fig. 26). Rinse the filter thoroughly and allow it to dry . Fig. 26 Air Filter Fig. 24 2. Remove the air filter (Fig. 25). Fig. 25 AIR FIL TER MAINTENANCE CLEAN AND RE-OIL THE AIR FIL TER EVERY 10 HOURS OF OPERA TION.
MAINTENANCE AND REP AIR INSTRUCTIONS 15 6. Reinstall the filter (Fig. 25) and air filter cover . NOTE: If the unit is operated without the carburetor/air filter cover assembled, you will VOID the warranty . The condition of the air filter is important to the operation of the unit.
16 0.025 inch (0.655 mm) CAUTION: Replace a cracked, fouled or dirty spark plug. Do not sand blast, scrape, or clean electrodes because the engine could be damaged by grit entering the cylinde r. REPLACING THE SP ARK PLUG Use a Champion RCJ-6Y spark plug (or equivalent).
17 TROUBLESHOOTING If further assistance is requir ed, contact your authorized service dealer . PROBLEM CAUSE ACTION Engine will not start Fouled spark plug Engine will not idle Engine will not accele.
18 SPECIFICA TIONS DRIVE SHAFT & CUTTING HEAD Drive Shaft Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum T ube (Click-Link) Throttle Contr ol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 The California Air Resources Board and Ryobi Outdoor Products (ROP), is pleased to explain the emission control system warranty on your 1995 and later lawn and garden equipment engine. In California, new lawn and garden equipment engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
R YOBI OUTDOOR PRODUCTS warrants each new R YOBI Product for two (2) years according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of original retail purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ryobi 2075r è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ryobi 2075r - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ryobi 2075r imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ryobi 2075r ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ryobi 2075r, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ryobi 2075r.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ryobi 2075r. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ryobi 2075r insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
