Manuale d’uso / di manutenzione del prodotto AXT-500 del fabbricante Audiovox
Vai alla pagina of 17
OWNER'S MANUAL Model AXT -500 500 Watt 4-Channel Bridgeable MOSFET Amplifier.
Specifications.....................................................................3 Precautions........................................................................ 4 Installation Instructions...................................................... 5 Wiring Instructions.
Input Impedance: Low-Level 10K Ohms High-Level 100 Ohms Input Sensitivity: Low-Level 200 mV - 8 V. High-Level 2V - 10 V Filter type: Selectable Full/Low-pass Crossover @ 12dB/Octave Filter Crossover: LPF 50-250 Hz (variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 30 amps.
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery.
1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode.
The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using.
4. Speaker Connections Depending on the type and number of speakers used with the amplifier , wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge.
-8- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250H.
-9- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-10- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250.
-11- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-12- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250.
-13- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-14- Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling of f to a normal operating range.
LPF Crossover Frequency Control This Control selects the crossover frequency when the Sub woofer Crossover Selector is in the "LPF" setting. Adjust it to the appropriate position for the characteristics and crossover frequency requirements of the speaker system with which the amplifier is being used.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
2003 Audiovox Electronics Corporation, Hauppauge, N.Y . C C Printed in Korea 128-6561 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Audiovox AXT-500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Audiovox AXT-500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Audiovox AXT-500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Audiovox AXT-500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Audiovox AXT-500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Audiovox AXT-500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Audiovox AXT-500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Audiovox AXT-500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
