Manuale d’uso / di manutenzione del prodotto APS-901 del fabbricante Audiovox
Vai alla pagina of 19
128-7765 1 of 19 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text.
128-7765 2 of 19 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn igni.
128-7765 3 of 19 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 .
128-7765 4 of 19 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then.
128-7765 5 of 19 This Remote S tart System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
128-7765 6 of 19 IMPORT ANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INT O THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCONNECT THE NEGA TIVE BA TTERY CABLE FROM THE VE- HICLE BA TTERY PRIOR TO MAKING ANY CONNECTIONS.
128-7765 7 of 19 SEE NEUTRAL S T ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch.
128-7765 8 of 19 Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or "CRANK" positions.
128-7765 9 of 19 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.
128-7765 10 of 19 the applications described below , a relay will be required. The Light Blue wire can be used to accommodate the following situations: A.
128-7765 11 of 19 cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a single coil unit for each cylinder , it may be necessary to connect this wire to more than one cylinder for proper tach reference.
128-7765 12 of 19 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows sof tware selections to control the way in which this output oper- ates, see remote start feature # 10 for setting this output.
128-7765 13 of 19 columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylinder number which appears in any of the circles. 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack.
128-7765 14 of 19 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. T emporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch. 4. Sitting in the vehicle, start the engine using the vehicle's ignition key .
128-7765 15 of 19 AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACT ORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
128-7765 16 of 19 C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to the Remote S tart Negative Safety Shut down Wire Gray/ Black, using a 4002 series diode as shown above.
128-7765 17 of 19.
128-7765 18 of 19 THIS PAGE LEFT BLANK INTENTIONALLY.
128-7765 19 of 19 © 2006 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7765.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Audiovox APS-901 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Audiovox APS-901 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Audiovox APS-901 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Audiovox APS-901 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Audiovox APS-901, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Audiovox APS-901.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Audiovox APS-901. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Audiovox APS-901 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
