Manuale d’uso / di manutenzione del prodotto U32-NG4 del fabbricante Regency
Vai alla pagina of 40
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-527 MODELS: U32-NG4 Natural Gas U32-LP4 Propane W ARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
2 U32-4 FPI Direct V ent Gas Insert FPI GAS INSERT Note: Oversize faceplate is 44" x 28" TO THE NEW OWNER Congratulations! Y ou are the owner of a state-of-the-art Gas Insert by FPI.
3 U32-4 FPI Direct V ent Gas Insert T ABLE OF CONTENTS FPI GAS INSERT OPERA TING INSTRUCTIONS Operating Instructions ................................................ 26 Lighting Procedure ...................................................... 26 Shutdown Procedure .
4 U32-4 FPI Direct V ent Gas Insert SAFETY LABEL This is a copy of the labels that accompany each U32-4 Gas Insert. We have printed a copy of the contents here for your review . The safety label is located on a plate inside the base of the unit visible when the bottom louver is opened.
5 U32-4 FPI Direct V ent Gas Insert REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chapter 10 (2) Revise 10.8. 3 by adding the follow ing additional re quirements: (a) For all side wall hor izontally v.
6 U32-4 FPI Direct V ent Gas Insert IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The FPI Gas Insert must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdiction to determine the need for a permit prior to starting the installation.
7 U32-4 FPI Direct V ent Gas Insert A B D E C MANUF ACTURED MOBILE HOME ADDITIONAL REQUIREMENTS 1) Ensure that structural members are not cut or weakened during installation. 2) Ensure proper grounding using the #8 ground lug provided. 3) Appliance must be anchored to the fl oor with the supplied anchoring methods.
8 U32-4 FPI Direct V ent Gas Insert VENTING THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SER VING A SEP ARA TE SOLID FUEL BURNING APPLIANCE. This appliance is designed to be attached to two 3" (76mm) co-linear aluminium fl ex running the full length of the chimney .
9 U32-4 FPI Direct V ent Gas Insert OPTIONAL BRICK P ANEL 1) Unwrap the brick pattern panels from the protective wrapping. 2) Remove the glass front if it is already installed, see "Standard Flush Door" section. 3) Put the rear brick panel fl at against the back of the unit.
10 U32-4 FPI Direct V ent Gas Insert 6) Place the Left T op Log D)02-46 on the pin on Log C)02-56 and on top of the cutout on Log A)02-43. 7) Place the notch in Center Log E)02-47 over Log B)02-45 and across the cutout on Log A)02-43.
11 U32-4 FPI Direct V ent Gas Insert Diagram 3 Rear View: T rim Assembly Diagram 2 Rear View: Faceplate Assembly Diagram 1 REGENCY F ACEPLA TE & TRIM INST ALLA TION 1) Lay the faceplate panels fl at, face down on something soft so they don't scratch.
12 U32-4 FPI Direct V ent Gas Insert T o remove the fl ush door, reverse the above steps. NOTE: The chain must rest on TOP of the gas inlet pipe never under it. Diagram 3 Diagram 2 Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket.
13 U32-4 FPI Direct V ent Gas Insert BA Y LOUVERS 1) Install top louver by sliding the two bracket clips into the brackets located on top of the bay door . See below . The fi tted louver leaves a small gap between faceplate bottom and louver top. Note: If any maintenance etc.
14 U32-4 FPI Direct V ent Gas Insert INST ALLA TION THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! 1) Shut off the gas supply . 2) Remove the louvers (and bay door if it is installed). 3) Open the fl ush door and remove the door .
15 U32-4 FPI Direct V ent Gas Insert Installation of the DC Sparker: 16) V erify that if the conversion is from NG to LPG, the screw must be re- assembled with the red o-ring visible (Fig. 5). LPG Configuration Red o-ring visible Fig.5 17) R e-assemble the black protection cap (Fig.
16 U32-4 FPI Direct V ent Gas Insert 28) Run the other end of the ground wire and DC spark generator wires through the bushing on the heat shield. 30) Plug the DC spark generator wires to the DC Sparker . 31) Connect the ground wire to the DC Sparker mounting bracket.
17 U32-4 FPI Direct V ent Gas Insert FULL SCREEN DOORS INST ALLA TION 1) Hold the full screen door frame up against the unit in order to make the following wire connections. Pull the ON/OFF connector wires from the fi rebox and connect them to the switch.
18 U32-4 FPI Direct V ent Gas Insert INST ALLA TION 5) Place Bottom Frame near hinge. Flip hinge over Bottom Frame and secure with 3 screws. 4) Install Spring Hinges on the Left and Right Side of the bottom of the fi rebox using 2 screws per hinge.
19 U32-4 FPI Direct V ent Gas Insert HAMPT ON ® CAST F ACEPLA TE INST ALLA TION 1) Lay the faceplate panels fl at, face down on something soft so they don't scratch. 2) Attach the side fi ller brackets to the left and right sides using 3 screws and washer per side.
20 U32-4 FPI Direct V ent Gas Insert HAMPT ON ® CAST GRILL INST ALLA TION INST ALLA TION Note: The top grill should be placed with the curved cut-out facing up. 11 ) Mount the cast faceplate panels onto the insert body , sliding the side fi ller brackets into the space between the glass and the fi rebox.
21 U32-4 FPI Direct V ent Gas Insert IMPORT ANT : Please use the gloves provided when handling the Kensington ® Front to avoid fi ngerprints. 3) Slide the T abs on the Blanking Plate into the slots located on Front and secure using 2 screws.
22 U32-4 FPI Direct V ent Gas Insert THE KENSINGT ON ® 2-P ANEL DOOR INST ALLA TION 3) Hook the Left Side Screen Door to the Door Frame by placing the door hinges (top & bottom) over the pins on the Door Frame. Repeat for Right Side Screen Door .
23 U32-4 FPI Direct V ent Gas Insert OPTIONAL REMOTE CONTROL Use the FPI Remote Control Kit approved for this unit. Use of other systems may void your warranty . The remote control kit comes with a hand held transmitter , a receiver and a wall mounting plate.
24 U32-4 FPI Direct V ent Gas Insert Piezo Ignitor Black Red To Thermocouple IN Pilot Assembly Thermostat (Optional) (Millivolt) Remote Receiver (Optional) (Millivolt) Remote T ransmitter (Optional) ON OFF Regency Burner ON OFF Ground Neutral Live Black Black Black Red Minimum Convection Air T emp.
25 U32-4 FPI Direct V ent Gas Insert For PROP ANE Units and Units Equipped with DC Spark Boxes* *For installation of the DC Spark Box refer to the LP Conversion instructions in this manual.
26 U32-4 FPI Direct V ent Gas Insert The glass panel may require cleaning after the unit has cooled down. DO NOT A TTEMPT TO CLEAN THE GLASS WHILE IT IS HOT . No te: When the glass is cold and the appliance is lit, it may cause condensation and fog the glass.
27 U32-4 FPI Direct V ent Gas Insert COPY OF LIGHTING INSTRUCTION PLA TE OPERA TING INSTRUCTIONS sounds. Y ou should also be aware that as there are temperature changes within the unit these sounds will likely re-occur . Again, this is normal for steel fi reboxes.
28 U32-4 FPI Direct V ent Gas Insert MAINTENANCE GENERAL VENT MAINTENANCE Conduct an inspection of the venting system semi-annually . Recommended areas to inspect as follows: 1) Check the V enting System for corrosion in areas that are exposed to the elements.
29 U32-4 FPI Direct V ent Gas Insert F AN MAINTENANCE If your fan requires maintenance or replacement, access to the fan is through the plate on the rear wall of the fi rebox. NOTE: the unit MUST NOT be operated without the fan access panel securely in place.
30 U32-4 FPI Direct V ent Gas Insert MAINTENANCE V AL VE REPLACEMENT 1) Shut off the gas supply . 2) Remove the louvers (and bay door if it is on). 3) Open the fl ush door and remove the door . 4) Remove the logs and brick panels. 5) Remove the grate by loosening the two screws and sliding the grate out.
31 U32-4 FPI Direct V ent Gas Insert P ARTS LIST 1) 420-122 Fan Access Panel 2) 420-142 Gasket - Fan Access Panel 422-518/P Fan Assembly: 3) 910-215/P Fan Motor (120 V) 5) 910-750 Power Cord (120 V) 9.
32 U32-4 FPI Direct V ent Gas Insert 69 73 74 71 52 58 70 72 90 91 55 68 67 68 66 O T L I P O TH TP TPTH TPTH E A A I R I N AIR IN 53 P ARTS LIST 423-574/P V alve Assembly - NG 423-576/P V alve Assembly - LP 52) 910-478 V alve - SIT NG / LP 53) 910-190 Ignitor Piezo and Nut 55) * V alve Tray 58) 904-240 Burner Orifi ce Nat.
33 U32-4 FPI Direct V ent Gas Insert P ARTS LIST Bay Door 420-931 Complete Bay Door with Black T rim 10 2) * Glass Retainer Side (T op & Btm) 10 3 ) * Glass Retainer Front (T op & Btm) 106) 94.
34 U32-4 FPI Direct V ent Gas Insert L O G O P L A T E H E R E LOGOPLATEHERE L O G O P L A T E H E R E LOGOPLATEHERE 92 95 ST ANDARD SIZE DET AIL 'A' 91 93 REAR VIEW FRONT VIEW 96 68 60 99 7.
35 U32-4 FPI Direct V ent Gas Insert 202 205 187 189 188 203 195 194 194 207 201 402-971** Cast Faceplates (Set) 187) 910-246 Burner On/Off Switch 188) 910-330 Fan Speed Control (120 V) 189) 904-733 K.
36 U32-4 FPI Direct V ent Gas Insert NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ _.
37 U32-4 FPI Direct V ent Gas Insert NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ _.
38 U32-4 FPI Direct V ent Gas Insert NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ _.
39 U32-4 FPI Direct V ent Gas Insert W ARRANTY FPI Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd.
Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Insta.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Regency U32-NG4 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Regency U32-NG4 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Regency U32-NG4 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Regency U32-NG4 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Regency U32-NG4, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Regency U32-NG4.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Regency U32-NG4. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Regency U32-NG4 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
