Manuale d’uso / di manutenzione del prodotto RHP 33 del fabbricante Raypak
Vai alla pagina of 19
Raypak ® RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL This manual should be maintained in legible condition and kept adjacent to the heat pump or in a safe place for future use. For additional information call: (03) 9757 3333 Effective Date: Dec 2004 Replaces: All Previous V ersions Part No.
PRODUCT SAFETY SIGNS AND LABELS This manual, as well as the pool/spa heat pump itself, contains product safety signs and labels. Please read these signs and labe ls, as they convey important safety information about hazards that may be potentially present in and around the heat pump.
RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I. Installation . . . . . . . .
Intr oduction This pool/sp a heat pump is an electro mechanical machine that incorporates a pressurised refrigerant gas in a sealed system. ONL Y trained and qualified service personnel should attempt to inst all or service this equipment.
• Each side of the unit must be located at least 300mm from walls, pipes, or other obstructions for unrestricted air intake and service access. Do not inst all the unit within 1m of fossil fuel burning heaters.
III. W ater Connections The heat pump inlet and outlet connections are NOT interchangeable. They must be connected as instructed below . 1. Connect the heat pump in the return water line between the pool filter and the pool. See page 10, Plumbing Diagrams.
Indicator Lamps : There are 6 indicator lamps located on the unit control panel: • Power (amber lamp): When lit, indicates power is applied to the unit. • Wa t e r Flow (green lamp): When lit, indicates normal water flow . • Heat Demand (green lamp): When lit, indicates the actual water temperature is below the target water temperature.
NOTE: The heat pump will be OFF when the Remote position is selected on the Po ol/Sp a selector switch. 4.Allow the heat pump to operate for a few minutes to stabilize operating pressures and to allow various component temperatures to normalize.
VIII. Summer Shutdown If you do not plan to use the pool heat pump during the summer months, secure and protect it as follows: 1. From the control panel, turn the control switch to Remote (OFF). 2. T urn the heat pump power switch to OFF. 3. Leave the valves set the way they are unless additional circulation is required.
2. B. Cabinet Care (optional) - The cabinet is designed for outdoor use and requires little care. However , you can clean it if you wish. 1. 2. W ash the cabinet with soap and water .
operation. After the desired temperature is reached, return the system to normal operation. •I s airflow through the unit being obstructed? Restrictions such as shrubbery , tall grass, dirty coils, or any other obstruction to airflow will reduce performance.
POWER SUPPL Y •V erify that all circuit breakers are reset and working properly . •I f t h e Power lamp on the control panel still does not light, contact the installing dealer , since it may be a power problem requiring an electrician. WAT E R F L O W •V erify that the filter is clean to provide good flow .
Plumbing Diagrams For systems with pumps of le ss than 2 HP(1.5Kw) (und er 300 l/min), no external bypass is required. Connections a re 50 mm pipe slip. Plumb the heat pump after the filter and before any chlorinators. Wa t e r I n (from pool or S pa) Wa t e r O u t (to pool or S pa) Filter For systems with pumps of 2 HP (1.
Heat Pump Schematic 12 4 3 A B C D 4 3 2 1 D C B A e l t i T n o i s i v e R r e b m u N e z i S A f o t e e h S 3 0 0 2 - n a J - 7 2 : e t a D : y B n w a r D b d d .
Contr ol Panel Assembly Replacement Parts List 12 4 7 13 11 10 16 11 9 15 2 5 8 14 3 6 1 ITEM QTY DESCRIPTION PART No. 11 Control Panel 21 Contactor Compressor 31 F a n Relay 41 Control Board 24Volt 5.
Contr ol Panel Cover Assembly Replacement Parts List 1 4 4 4 7 6 7 6 8 8 5 Front ITEM QTY DESCRIPTION PART No. 11 Control Panel Cover 22 P O T 31 S w i t ch Type A403 43 K n o b 51 Label Control Panel.
Heat Pump Assembly Replacement Parts List - RHP 3 3 11 15 13 12 5 9 2 9 16 7 7 18 14 6 7 3 17 19 4 10 1 8 Model RHP 33 *See assembly drawing in this manual IT EM QTY DESCRIPTION PART No.
15.
16.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Raypak RHP 33 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Raypak RHP 33 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Raypak RHP 33 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Raypak RHP 33 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Raypak RHP 33, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Raypak RHP 33.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Raypak RHP 33. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Raypak RHP 33 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
