Manuale d’uso / di manutenzione del prodotto PLCD10MR del fabbricante Pyle
Vai alla pagina of 16
OWNER’S MANUAL Mobile Audio System • MP3/CD Player • PLL Synthesizer Stereo Radio • Compact Disc Player • Automatic Memory Storing • Full Detachable Panel • Preset Equalization • Electronic Shockpr oof (ESP) Function • Auxiliary Input Function • Remote Control www .
2 CONTENTS Installation ........................................... 3 T ake out screw befor e installation.........3 DIN Front-Mount (Method A) ................3 Installing the unit .................................3 Removing the unit ................
3 INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly .
grounding of the unit. Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard. 10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel.
DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.
USING THE DET ACHABLE FRONT P ANEL REMOVING THE FRONT P ANEL 1. Pr ess the release button (RELEASE) on the front panel and pull of f the front panel. 2. Keep fr ont panel into the case. INST ALLING THE FRONT P ANEL T o install the front panel, insert the panel into the housing and make sure the panel is properly installed.
7 WIRING CONNECTION FRONT Lch SPEAKER GREEN GREEN/BLACK MEMORY BACK-UP (B+) MAIN UNIT IGNITION SWITCH (ACC+) POWER ANTENNA RED GROUND (B–) YELLOW BLACK BLUE REAR RCA CABLE ANTENNA CONNECTOR (GREY) R.
8 OPERA TION LOCA TION OF KEYS 24 7 9 14 3 6 15 5 8 4 11 10 25 2 1 23 22 21 20 18 13 19 17 12 16 26.
9 OPERA TION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except button (7) and button (4)). When system is on, press button (9) to turn off the unit. F ACEPLATE RELEASE Press button (7) to detach the removable faceplate. SOUND ADJUSTMENT Press SEL button (10) to select the desir ed adjustment mode.
10 RADIO OPERA TION • SWITCHING TO RADIO MODE Press MODE button (6) shortly to select radio mode, the radio mode appears in the display together with the memory band and frequency . • SELECTING THE FREQUENCY BAND At radio mode, press BND/LOU (ENT) button (13) shortly to select the desired band.
11 OPERA TION • PLA YING ALL TRACKS IN RANDOM Press SHF button (23) to play all tracks on CD in random order . Press again to cancel the function. • EJECTING A DISC Press button (4) to stop CD playing and eject the disc from the disc slot (5).
12 OPERA TION (‘ ‘), then - Use the TUNE/TRACK UP/DOWN buttons to list all songs under this directory and select the title. - Press BND/LOU (ENT) button to confirm and start the play . - Repeat the above steps if the newly selected title is again a directory .
13 REMOTE CONTROL HANDSET FUNCTION KEYS & CONTROL 1. PWR Power ON/OFF Button 2. DSP (0) Display Button (_,-,+,0 For MP3/WMA Operation) 3. SEL Sound Mode Select Button (Character Shift Right For MP3/WMA Operation) 4. VOL V olume Up Button (Character Select (A, B~8,9,0) For MP3/WMA Operation) 5.
14 OPERA TION DISC NOTE A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use r ound shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recor ding side of any discs, as it may cause a malfunction.
15 GENERAL P o wer Supply Requirements : DC 12 V olts, Negative Ground Chassis Dimensions : 178 (W) x 160 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : ± 10 dB - T reble (at 10 KHz) : ± 10 dB Maximum Output P ower : 4 x 25 W atts Current Drain : 5 Ampere (max.
TROUBLE SHOOTING Before going thr ough the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power . The car ignition switch is If the power supply is not on.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pyle PLCD10MR è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pyle PLCD10MR - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pyle PLCD10MR imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pyle PLCD10MR ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pyle PLCD10MR, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pyle PLCD10MR.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pyle PLCD10MR. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pyle PLCD10MR insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
