Manuale d’uso / di manutenzione del prodotto EN250RYLB-O del fabbricante Procom
Vai alla pagina of 21
1 COMP ACT VENT -FREE FIREPLACE SYSTEM OWNER ’ S OPERA TION AND INST ALLA TION MANUAL Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS Do not try to light any appliance.
2 T abel of Contents Safety Information W arnings...................................3 Air for Combustion and V entilation.........................5 Installation.............................................................7 Operating heater............
3 IMPORT ANT : Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
4 SAFETY INFORMA TION Continued 15. Turn off and unplug heater and let cool before servicing. Only a qualified service person should service and repair heater. 16. Operating heater above elevations of 4,500 feet could cause pilot outage. 17. Do not operate heater if any log is broken.
5 AIR FOR COMBUSTION AND VENTILA TION W ARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventila- tion air. Read the following in- structions to insure proper fresh air for this and other fuel-burning appliances in your home.
6 W ARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space.
7 NOTICE : This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system's circulating blower while using heater.
8 CONNECTING T O GAS SUPPL Y W ARNING : A qualified service person must connect heater to gas supply. Follow all local codes. CAUTION: Never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). lnstall the external regulator between the heater and gas supply.
9 W ARNING: T est all gas piping and connections for leaks after install- ing or servicing. Correct all leaks at once. W ARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak.
10 W ARNING: Failure to position the parts in accordance with these diagrams may result in property damage or personal injury. CAUTION: After installation and periodically thereafter, check to en- sure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log.
11 b.manual select of main burner: Press BURNER button, the flame is on “MAN” select. At this selection, the main burner will keep working no matter what the temperature is set at. If there is a need to shut off the main burner, just press the “BURNER” button to make the burner on the “OFF” select.
12 3.After completion of the above-men- tioned two steps, the transmitter is kept in a state of readiness. If the appliance doesn’t working for a period time, just pull out the plug from the 1 10V electrical outlet. OPERA TIONS OF KEY -PRESS LOCKING 1.
13 Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 24). With the unit off, lightly blow air through the air inlet hole.
14 TROUBLESHOOTING ODS/pilot lights but flame is continuous igniting and the main burner couldn’t be lit. 1. Thermocouple connection loose at control board 2. Pilot flame not touching thermcouple which allows thermocouple to cool, causing pilot flame to go out.
15 SPECIFICA TIONS Btu 20,000/25,000 20,000/ 25,000 Gas T ype LP Gas Natural Gas Ignition Automatic Automatic Manifold Pressure 8"W.C. 3"W.C.
16 REPLACEMENT P ARTS Note : Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. P ARTS UNDER W ARRANTY Contact authorized dealers of this product. If they can't supply original replacement part(s) call PRO-COM at (877) 886-5989 for referral information.
17 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250RYLB-O.
18 P ARTS LIST This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 16 of this manual.
19 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250R YLB-O.
20 P ARTS LIST Y E K O N T R A P R E B M U N N O I T P I R C S E DY T Q 10 0 0 3 3 B Ey l b m e s s A s g o L g n i t a r o c e D1 2B 1 0 - 0 4 0 L E) B ( l e n a P p o T1 36 0 - 6 1 0 L El e n a P g .
21 Install the decorating logs. Fasten decorating logs 1 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 2 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 3 on to the co rresponde nt angle iron ( Figure 4 ). Insert the pinhole on the upper part of log 4 into the pin on the left side of log 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Procom EN250RYLB-O è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Procom EN250RYLB-O - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Procom EN250RYLB-O imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Procom EN250RYLB-O ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Procom EN250RYLB-O, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Procom EN250RYLB-O.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Procom EN250RYLB-O. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Procom EN250RYLB-O insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
