Manuale d’uso / di manutenzione del prodotto A1000/2 del fabbricante Precision Power
Vai alla pagina of 23
AMPLIFIER MODELS A500/2 A800/2 A1000/2.
T ABLE OF CONTENTS Congr atulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Ser vice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . .
CONGRA TULA TIONS Thank y ou f or choosing Precision P o wer TM audio equipment. Designed and engineered in the USA, this product combines innov ative technology with the finest materials to consistently deliv er Absolutely State of the Ar t ™ perf ormance, sound quality , reliability , and v alue .
High V oltage Input Capability with -12dB Atten uation Switch. Gold Plated RCA Input and Output Connectors. Po w e r Lock TM Speak er and P ower Wire Connectors. WHA T’S INCLUDED Amplifier (with speak er and pow er plugs mounted) (4) Mounting scre ws and washers 2mm he x wrench 2.
SPECIFICA TIONS Nominal Power Ratings MODEL 4 ohm 2 ohm 4 ohm MONO A500/2 2 X 75 2 X 125 1 X 250 A800/2 2 X 125 2 X 200 1 X 400 A1000/2 2 X 175 2 X 250 1 X 500 General Specifications Load Impedance (S.
5 Fuse Requirements Y ou will need to install an in-line fuse or circuit break er in the pow er wire within 18” of the batter y . This fuse or circuit break er is to protect y our v ehicle from fire in case the po wer wire shor ts to the v ehicle body .
AMPLIFIER ST A TUS LEDS The LEDs provide the f ollowing indications: 1. P ower - These LEDs illuminates the center Precision P o wer logo bac kground when the amplifier po wer is turned on. 2. Shor t - These LEDs behind the PPI logo will flash to indicate a shor t on the output.
T OOLS/P ARTS FOR INST ALLA TION NO TE: T OOLS ARE NO T SUPPLIED . Small flat b lade scre wdriver Phillips scre wdriver (#2 or medium siz ed) Wire cutters Wire strippers 4 - #6 round head scre ws, and 1 - #8 sheet metal scre w .
Note: The cables running from the battery to the rear of the car should be installed on the side of the car opposite to the antenna. When using 16 gauge wire or larger , run the speaker wires from the amplifier location through the v ehicle to the speak ers .
Note: The amplifier comes with the connector inser ted into the amplifier with the wire c lamping screws in the up position as shown belo w . Use a 2mm hex head wrenc h to secure the wires to the connector . If the connector needs to be unplug ged from the amplifier , use a 2.
wires as close together as possib le, and use the same gauge wire f or both. This will ensure that y ou ha v e a good g round path, and ma y eliminate such potential prob lems as engine noise and ov erheated amplifiers.
375W = 31.25 Amps total current dra w 12V If the same amplifier is driven into a 2 ohm stereo or 4 ohm mono load, doub le it’ s 4 ohm RMS rating. These amplifiers will eff ectiv ely doub le their pow er at this load. 250W X 1.5 X2 = 750 watts 750W = 62.
PO WER LOCK CONNECT ORS Once y ou ha v e run both the power and g round wires , then connect the cab les to the amplifier . Cut off e xcess wire, and using wire strippers, strip the ends of the power and g round cab les appro ximately 1/4 inch. Locate the Po w e r Loc k TM pow er and ground connector (supplied).
FR ONT PLA TE DIA GRAM 1. Cooling Plenums: Maintain a minim um 2” clearance around cooling plenums f or proper amplifier cooling. 2. Speaker/Remote Connector: The P ower Loc k TM speak er connector . 3. Output Xo ver Freq. Control: Use this control to adjust the sub bass output signal crossov er frequency from 30Hz to 4kHz.
QBass frequency control adjustment. 12. RCA Outputs: RCA outputs provide HP/LP/FULL 30-4kHz signal to another amplifier . END PLA TE DIA GRAM 1. Cooling Plen ums: Maintain a minimum 2” clearance around cooling plenums f or proper amplifier cooling. 2.
INPUTS There are two sets of RCA jac ks on the front end of y our amplifier . The RCA cab les from y our source unit go in the set labeled INPUTS . If your source unit doesn’t ha v e RCA outputs, then add a set of RCA plugs (a v ailab le at y our dealer) to y our front or rear set of speak er leads (see dra wing belo w).
QB ASS PLUS SPECIFICA TIONS Note: Not a v ailab le on the model A500/2 amplifier . QB ASS PLUS TM Up to 18dB of boost with selectab le center frequency at 30Hz, 36Hz, 44Hz or 60Hz, with a Q-f actor of 2. Optional QB ASS REMO TE TM This boost control can be mounted in the dash and will supersede the boost control on the amplifier endplate.
QB ASS PLUS/QB ASS REMO TE On A800/2 , and A1000/2 amplifiers, w e’v e tak en bass control to a higher le v el with QB ASS PLUS TM . The two QB ASS TM s witches (labeled 1 and 2) on the front end of the amplifier allow y ou to select one of f our frequency centers 30Hz, 36Hz, 44Hz and 60Hz.
TC-X CR OSSO VER Y our ne w amplifier has a TC-X Crossov er (T otal Control X-ov er ® ) 30Hz-4kHz (see this guide f or Crosso v er Char t).12dB per octa v e phase correlated crossov er built-in to pro vide superior system fle xibility without the added e xpense and installation of an outboard crossov er .
CR OSSO VER DETENT CHART Detent # Low P ass F requency (Hz) @ -3dB High P ass F requency (Hz) @ -3dB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 .
ADJUSTING INPUT GAIN 1. Adjust all amplifier input gain controls to just abov e minimum sensitivity (fully countercloc kwise). 2. Using the cleanest music source (CD) pla ying, tur n up the head unit source v olume until y ou can hear distor tion. No w tur n it do wn a bit until y ou cannot hear the distor tion (usually just below full v olume).
TROUBLESHOO TING NO SOUND Is the LED illuminated? YES NO Chec k P ower and Remote tur n-on wire f or voltage . Mak e sure the ground wire is secure. STILL NO SOUND See your A uthor iz ed Precision P ower TM Dealer or call 1-800-62PO WER.
LIMITED TW O YEAR CONSUMER W ARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prov e to be def ective in w orkmanship or mater ial under nor mal us.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Precision Power A1000/2 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Precision Power A1000/2 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Precision Power A1000/2 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Precision Power A1000/2 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Precision Power A1000/2, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Precision Power A1000/2.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Precision Power A1000/2. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Precision Power A1000/2 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
