Manuale d’uso / di manutenzione del prodotto 530088886 del fabbricante Poulan Pro
Vai alla pagina of 16
220 LE / 260 LE Operator’s Manual Manual del Operador Manuel de L’utilisateur WAR NI NG : Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so c an result in serious injury. ADVERT ENC IA : Lea el manual del operador y siga todas las advertencias e enstruc- ciones de seguridad.
2 SAFETY RULES W ARNING: Alway s disconnect spark plug wi re and place wire where it can- not contact spark plug to prev ent acc idental starti ng when set ting up, transport ing, ad- justi ng or mak ing repairs exc ept carburetor adjustm ents.
3 marked c ontainer for all fuel purposes . Wipe up all fuel spills before starting s aw . S Move at least 10 feet (3 met ers) from fuel- ing sit e before s tarting engine. S Turn the engine off and l et saw cool in a non-combust ible area, not on dry leaves , straw, paper, etc.
4 Thumb on underside of handlebar Elbow loc ked S Keep a good, firm grip on the saw with both hands when t he engine is running and don’t let go. A firm grip will help you reduce kick back and mai ntain cont rol of the saw. Keep the fingers of your lef t hand enc ir- cling and your left thumb under the front handlebar .
5 and bar as origi nal equipment. Repairs on a chain brak e shoul d be m ade by an autho- rized servic ing dealer. T ake your unit to t he place of purchase if purc hased from a ser- vici ng deal er, or to t he neares t authori zed master s ervice deal er.
6 S Replace t he chain brake nuts and tight en finger t ight. O nce the chain is tens ioned you will need to tight en c hain brake nut s. Mount the Bar Proper cha in direction Tip of Bar Place chain o.
7 OPERA TION KNOW YOUR SA W READ THIS OPERA TOR ’S MANUAL AND SAFETY RULES BEFO RE OPERATIN G YOU R CHAIN SAW . Compare t he illustra tions with your unit to familiarize yourself with the location of the various controls and adjus tments. Save thi s manual f or future ref erence.
8 FUEL ING & LUBR ICATION W ARNING: Remove fu el ca p slow - ly when ref ueling. FUELING ENGINE This engi ne is certi fied t o operate on unleaded gasoline. B efore operation, gasoline mus t be mix ed wi th a good qualit y synthe tic 2- cycle air- cooled engine oil designed to be mix ed at a ratio of 40:1.
9 ON STOP ON/STOP SWITCH OFF FULL CHOKE/FAST IDLE LEVER Choke/Fast Idle Lever (SIDE VIEW ) ST ARTING A W ARM ENGINE: S Move ON/STOP swi tch to the ON posi tion. S Pull the choke/f ast idl e lever out to the full extent, then push t he l ever back in c om- pletely (to t he OFF posi tion).
10 S Keep the chain out of dirt and s and. E ven a small amount of dirt will qui ckly dull a chain and thus increa se the possibility of kick- back. S Practi ce cutt ing a few small logs us ing the following t echniques to get t he “feel” of us- ing your s aw before you begin a maj or sawing operati on.
11 Opening of felling cut Closing of notch Hinge holds tree on s tump and helps control fall NOTE: Before felling cut is c omplete , use wedges t o open the cut when necessary to control the direction of f all. T o avoid kickbac k and chain damage, us e wood or plast ic wedges, but never steel or i ron wedges .
12 S Finish wi th your s econd cut. 1 st Cut 2 nd Cut U s i n gal o gf o rs u p p o r t 2 nd Cut 1 st Cut 1 st Cut 2 nd Cut Using a support stand 1 st Cut 2 nd Cut LIMBING AND PRUNING W ARNING: Be alert f or and guard against kic kback.
13 SERVICE W ARNING: Disc onnect t he spark plug before performing maint enance except for carburet or adjust ments. We recommend all servic e and adj ustments not l isted in t his m anual be performed by an authorized or Mast er S ervice Dealer. MAINTENANCE SCHEDULE Lubric ate bar sprocket hole After each use .
14 CARBURETOR ADJUSTMENTS Y our c arburetor is equipped wit h limiter caps. Carburet or adjus tment is a c ompli- cated task. W e recommen d that you take your unit to an Authoriz ed Serv ice Dealer. Damage wil l occur if you turn the needles be- yond the li miter s tops.
15 TROUBLE CAUSE REMEDY Engine will not start or w ill run only a few seconds af ter starti ng. S Ignition swit ch off. S Engine flooded. S Fuel tank empt y. S Spark plug not f iring. S Fuel not reaching carburetor . . S Move ign ition switch to ON. S See “Diff icult Start ing” in Operation Sec tion.
16 be designed, built , and equipped to meet the State’s stringent anti - - smog standards. POU- LAN /WEED EA TER must warrant th e emis - sion control system on your small off - - road en- gine f or the periods of t ime li sted below provided there has been no abuse, neglect, or improper maintenance of your small off- - road engine engine.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Poulan Pro 530088886 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Poulan Pro 530088886 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Poulan Pro 530088886 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Poulan Pro 530088886 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Poulan Pro 530088886, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Poulan Pro 530088886.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Poulan Pro 530088886. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Poulan Pro 530088886 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
