Manuale d’uso / di manutenzione del prodotto PDC18H42STA del fabbricante Poulan
Vai alla pagina of 48
OWNER'S MANUAL MODEL: PDC18H42ST A LA WN TRACTOR AL W A YS WEAR EYE PROTECTION DURING OPERA TION W ARNING: Read this Owner's Man u al and follow all W arn- ings and Safety Instructions. Fail ure to do so can re sult in serious in ju ry . IMPOR T ANT MANUAL Do Not Throw A way 186274 12.
2 DO NO T : • Do not turn on slopes unless necessar y , and then, turn slowly and gradually do wnhill, if possible. • Do not mow near drop-offs , ditches, or embankments. The mower could suddenly turn ov er if a wheel is ov er the edge of a cliff or ditch, or if an edge cav es in.
3 W ARNING: In order to pre vent ac- ci den tal starting when setting up, trans por t ing, ad just ing or making re- pairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, you ma y lose control of the tractor .
4 GASOLINE CAP A CITY 2.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W30 (above 32°F) SAE 5W -30 (below 32°F) OIL CAP A CITY : W/FIL TER 4.0 PINTS W/O FIL TER 3.5 PINTS SP ARK PLUG: CHAM PI ON RC12YC (GAP: .040") GROUND SPEED (MPH): Forward: 0-5.
5 UNASSEMBLED P AR TS (1) Large Flat Washer Steering Wheel Insert Steering Sleeve Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Mulch Blades (2) Keys Slope Sheet Steering Extension Shaft Steering Adapter (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 (4) Washers 3/8 x 3/4 x 14 Ga.
6 HO W T O SET UP Y OUR TRA CT OR INST ALL SEA T (See Fig. 2) Adjust seat bef ore tightening adjustment knob . • Remove adjustment knob and fl at w asher securing seat to cardboard packing and set aside f or assembly of seat to tractor . • Piv ot seat upward and remov e from the cardboard pack- ing.
7 ASSEMBL Y FIG. 2 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T FIG. 3 SEA T P AN LABEL CHECK B A TTER Y (See Fig. 3) • Lift seat pan to raised position. • If this batter y is put into ser vice after month and year indicated on label (label located between terminals) charge batter y f or minimum of one hour at 6-10 amps.
8 ASSEMBL Y ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRAC- TOR, WE WISH T O ASSURE THA T Y OU RECEIVE THE BEST PERFORMANCE AND SA TISF A CTION FROM THIS QU ALITY PRODUCT . PLEASE REVIEW THE FOLLOWING CHECKLIST : ✓ All assembly instructions hav e been completed.
9 OPERA TION These symbols ma y appear on your tractor or in liter ature supplied with the product. Lear n and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models.
10 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to f amiliarize yourself with the locations of v arious controls and ad just ments. Sav e this manual for future ref erence.
11 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age . Alwa ys wear safety glass es or eye shields while operating your tractor or per for m ing any adjustments or repairs.
12 OPERA TION T O OPERA TE ON HILLS W ARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across an y slope. • Choose the slowest speed bef ore star ting up or down hills. • Av oid stopping or changing speed on hills.
13 OPERA TION T O ST ART ENGINE (See Fig. 5) When star ting the engine for the fi rst time or if the engine has run out of fuel, it will take e xtra cranking time to mo ve fuel from the tank to the engine. • Be sure freewheel control is in the transmission en gaged position.
14 FIG. 10 MO WING TIPS • Mower should be properly le veled f or best mowing per- f or mance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mower should be used f or tr im- ming. • Dr ive so that clippings are discharged onto the area that has been cut.
15 MULCHING MO WING TIPS IMPORT ANT : FOR BEST PERFORMANCE, KEEP MO WER HOUSING FREE OF BUIL T -UP GRASS AND TRASH. CLEAN AFTER EA CH USE. • The spe cial mulch ing blade will recut the gr ass clip- pings many times and reduce them in size so that as they f all onto the lawn they will disperse into the g rass and not be noticed.
16 MAINTENANCE B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Pa.
17 MAINTENANCE BLADE REMO V AL (See Fig. 12) • Raise mower to highest position to allow access to bla d e s. • Remov e blade bolt, lock washer and fl at was he r se cur ing bla d e. • Install new or resharpened blade with trailing edge up tow ards deck as sho wn.
18 CLEAN AIR SCREEN Air screen must be k ept free of dir t and chaff to prev ent engine dam age from o verheating. Clean with a wire br ush or compressed air to re mov e dir t and stubbor n dried gum fi bers. MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary .
19 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spar k arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whiche ver occurs fi rst.
20 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS • Depress clutc h/brake pedal fully and set parking brake. • Place motion control le ver in neutral (N) position. • Place attachment c lutch in “DISENGA GED” position.
21 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 21 NUT "F" FRONT LINKS FIG. 22 FRONT -T O-BA CK ADJUSTMENT (See Figs.
22 SER VICE AND ADJUSTMENTS FIG. 23 T O REPLA CE MO WER BLADE DRIVE BEL T (See Fig. 23) The mower b lade dr ive belt ma y be replaced without tools. P ark the tractor on le vel surf ace. Engage par king brake . BEL T REMO V AL - • Remov e mower from tractor (See “T O REMO VE MO W ER” in this section of manual).
23 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 27) • Block up axle securely . • Remo ve axle co ver , retaining ring and washers to allow wheel remov al (rear wheel contains a square ke y - Do not lose). • Repair tire and reassemble.
24 SER VICE AND ADJUSTMENTS FIG. 29 FIG. 30 T O REPLA CE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push b ulb holder securely back into the hole in the bac kside of the grill.
25 SER VICE AND ADJUSTMENTS HOOD T O REMO VE HOOD AND GRILL ASSEMBL Y (See Fig. 31) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides , tilt toward engine and lift off of tractor . • T o replace, re v erse abov e procedure.
26 ST ORA GE Immediately prepare your tr actor for stor age at the end of the season or if the tractor will not be used f or 30 da ys or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
27 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. W ait sev eral minutes bef ore attempting to star t.
28 PROBLEM CA USE CORRECTION TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Chec k wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutc h depar tment.
29 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 SCHEMA TIC 87 87A 85 86 30 RELAY WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED F SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
30 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 30 90 8 2 1 27 16 16 52 22 21 D .
31 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 ELECTRICAL 1 163465 Batter y 12 V olt 25 Amp 2 74760412 Bolt He x Hd 1/4-20unc X 3/4 8 176689 Box Battery 16 176137.
32 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 CHASSIS AND ENCLOSURES 26 25 58 64 208 13 208 11 1 3 2 9 208 209 208 5 5 207 3 3 3 142 3 3 3 142 17 29 28 12 51 57 .
33 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 CHASSIS AND ENCLOSURES 1 174619 Chassis 2 176554 Dra wbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 9 168337X012 Dash 10 72140608 Bolt RdHd Sqnk. 3/8-16 Unc x 1 11 174996 Panel Asm.
34 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 DRIVE 66 29 28 32 30 52 32 59 38 61 41 53 35 55 36 62 35 36 22 39 34 16 1 77 77 30 52 56 64 65 212 63 116 70 57 96 .
35 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - T ransaxle Hydro Gear Model 314.
36 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 STEERING ASSEMBL Y 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 .
37 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 STEERING ASSEMBL Y 1 180656 Wheel Steering 2 172393 Axle Asm Front 3 169840 Spin dle Asm Lh 4 169839 Spin dle Asm R.
38 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 ENGINE 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 105 105 3 16 101 77 4 80 101 13 23 45 14 38 44 46 32 31 33 37 33.
39 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 ENGINE NO TE: All component dimensions giv en in U .S. inches 1 inch = 25.
40 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 SEA T ASSEMBL Y KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO .
41 WHEELS & TIRES KEY P ART NO . NO . DESCRIPTION 1 59192 Cap V alve Tire 2 65139 Stem V alve 3 170455 Tire F Ts 15 X 6 0 - 6 Ser vice 4 59904 T ube F ront (Ser vice Item Only) 5 106732X421 Rim As.
42 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 MO WER LIFT 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 23 24.
43 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 MO WER LIFT 1 184418 Plunger Asm. 2 159471 Shaft Asm Lift 3 105767X Pin Groov e 4 12000002 E Ring #5133-62 5 19211621 Washer 21/32 x 1 x 21 Ga.
44 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 MO WER DECK 15 14 13 11 10 9 8 16 68 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 49 50 51 54 52 53 55 56.
45 REP AIR P ARTS TRA CT OR - - MODEL NUMBER PDC18H42ST A, PRODUCT NO . 954 57 07-89 MO WER DECK 1 182032X421 Mow er Deck Assemb ly , 42" 2 72140506 Bolt 3 138017 Bracket Asm F r .
46 LIMITED W ARRANTY The Manuf acturer warrants to the original consumer purchaser that this product as manuf actured is free from defects in materi- als and work man ship .
47 15 DEGREES MAX. FO LD ALO NG DOTTED LINE THIS IS A 15 DEGREE SLO PE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Y our POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLACEMENT P AR TS: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Poulan PDC18H42STA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Poulan PDC18H42STA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Poulan PDC18H42STA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Poulan PDC18H42STA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Poulan PDC18H42STA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Poulan PDC18H42STA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Poulan PDC18H42STA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Poulan PDC18H42STA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
