Manuale d’uso / di manutenzione del prodotto PP2000 del fabbricante POSIFLEX Business Machines
Vai alla pagina of 30
Rev. A PP2000 Series 2 Station Printer User’s Guide.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
PP2000 (E) User’s Manual i Table of Contents PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 MAIN PARTS ON THE EXTERIOR . . . . . . 2 -- 1 OUTPUT AREAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1 CONTROL PANEL .
PP2000 (E) User’s Manual ii STORE STAMP (OPTION) . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 INTERNAL SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 CASH DRAWER CONNECTOR . . . . . . . . . . . . . . . . . 6 -- 5 SERIAL INPUT CONNECTOR (STANDARD 9 PIN RS232 INTERFACE) .
PP2000 (E) User’s Manual 1 - 1 I. PRODUCT BRIEFING This is a high speed 2 - station journal / receipt printer. l A standard 2 station Journal / Receipt printer: The printing paper width is 44.5 mm. The printer can print both journal and receipt at the same time or only journal or receipt alone.
PP2000 (E) User’s Manual 1 - 2 l Options include auto stamping ability of the store stamp on receipt and auto cutting of the receipt. l The ability of cutting paper in full or in part by software on receipt .
PP2000 (E) User’s Manual 2 - 1 II. MAIN PARTS ON THE EXTERIOR A. OUTPUT AREAS B. CONTROL PANEL Receipt exit slot Journal window Validation printing insert slot Power LED On line LED Power On/Off swi.
PP2000 (E) User’s Manual 2 - 2 C. INPUT / OUTPUT CONNECTOR Cash drawer connector Serial connector Power connector Parallel connector.
PP2000 (E) User’s Manual 3 - 1 III. INS TALL ATION A. CHECK CONTENTS When you unpack carefully the carton that delivers PP2000 series printer, you will find it contains several items as illustrated below.
PP2000 (E) User’s Manual 3 - 2 C. STORE STAMP INSTALLATION If your printer comes with stamp option, you can find a store stamp case in the rear of the receipt part of print anvil assembly. You may take it out gently by holding its handle with your fingers.
PP2000 (E) User’s Manual 3 - 3 of store stamp. When the printing ink of the stamp is not enough , you can drip printing ink into the two holes in the rear of the stamp case. D. R IBBON INSTALLATION / REPLACEMENT When replacing the ribbon, please take the handle at the center of the old ribbon case and lift it up.
PP2000 (E) User’s Manual 3 - 4 turn the knob of the ribbon in the marked direction to tighten the ribbon and to ensure proper operation of the ribbon and to avoid jamming. E. CASH DRAWER CONNECTION Using the Posiflex signal cable CCBLA-180 to control a Posiflex cash drawer ( CR3100 or CR3200).
PP2000 (E) User’s Manual 3 - 5 H. POWER ON Turn on the On/Off switch at the left to the control panel, there will be a short buzzing sound and it indicate s a normal power on. I. PAPER ROLLS INSTALLATION 1. Please refer to the picture above: Put the receipt roll into the left paper roll compartment and the journal roll into the right.
PP2000 (E) User’s Manual 3 - 6 4. To give an idea about the positioning matter of the receipt, the print center is 33.3 mm behind the auto-cut position, whilst the stamp center is 40.
PP2000 (E) User’s Manual 4 - 1 IV. MAINTENANCE NOTICES l The printer should be put at a well ventilated site and avoid direct sunshine, also avoid high temperature, high humidity, high magnetic field. The site should also be free from lots of metal chips and dust.
.
PP2000 (E) User’s Manual 5 - 1 V. SOFT WA RE COMMANDS The commands supported by the PP2000 Printer are listed below. For detail description of the below listed commands, please visit our web site http://www.posiflex.com.tw for detail descriptions of each command.
PP2000 (E) User’s Manual 5 - 2 Software commands continued. NAME HEX FUNCTION ESC o 1B 6F Stamp ESC p 1B 70 Generate pulse ESC t 1B 74 Select character code table ESC u 1B 75 Transmit peripheral dev.
PP2000 (E) User’s Manual 6 - 1 VI. SPECIFIC ATIONS A. VALIDATION PRINTING Paper width: 140 mm or above Paper height: 65 mm or above Paper thickness: 0.07 ~ 0.14 mm Validation print: One line Number of characters: 55 Print area and sensor position: As illustrated in drawing above B.
PP2000 (E) User’s Manual 6 - 2 C. LED INDICATIONS Power LED: Green: Printer power is working On line LED: Green: Printer is at on line state. The printer takes command from the host system at this state and takes no command from the buttons. Receipt LED: Red: Receipt pa per is out, or malfunction with receipt print.
PP2000 (E) User’s Manual 6 - 3 E. PRINTER GENERAL SPEC ITEM SPECIFICATION Functions Receipt, journal and validation printing Printing Method 9 pin dot matrix impact; synchronized or separate printing of receipt and/or journal Printing Speed About 3 lines/sec.
PP2000 (E) User’s Manual 6 - 4 F. STORE STAMP (OPTION) Cushion width: 34.0 mm Cushion height: 24.0 mm Cushion thickness: 1.0 mm Cushion material: PE foam Stamp total width: 34.0 mm Stamp total height: 24.0 mm ( engraving included ) Stamp total thickness: 5.
PP2000 (E) User’s Manual 6 - 5 H. CASH DRAWER CONNECTOR PIN DEFINITION 1 Frame ground 2 CR2 kick (by Esc p 0 n1 n2) 3 Drawer open sense 4 +24 V DC power 5 CR1 kick (by Esc p 1 n1 n2) 6 Signal ground I. SERI AL INPUT CONNECTOR ( standard 9 pin RS232 interface) J.
PP2000 (E) User’s Manual 6 - 6 M. ENVIRONMENT Temperature: 0 ° C to 50 ° C Humidity: RH 10% to RH 90% without condensation N. RELI ABILITY Printer mechanism (without print head) life: 8,000,000 lines Print head life: 150,000,000 characters (2 dots/wire/character average) O.
PP2000 (E) User’s Manual 7 - 1 VII. REGULAR MAINTENANCE PROCEDURE A. DAILY MAINTENANCE Perform a basic cleaning and maintenance daily at a suitable timing as following 1. Turn power off and open the top cover. Press down the receipt lever and the journal lever.
PP2000 (E) User’s Manual 7 - 2 B. PERIODIC M AINTENANCE A periodic maintenance and lubrication should take place by a qualified maintenance specialist in every 6 months.
PP2000 (E) User’s Manual 8 - 1 VIII. BASIC TROUBLE SHOOTING A. NO OPERATION AFTER POWER ON If the printer does not work, neither does the power on LED lit: 1. Check if the power cord is well connected. 2. Check if the power outlet the printer is connected to is supplied with power.
PP2000 (E) User’s Manual 8 - 2 D. PAPER JAMMED In case of serious paper jammed problem, please pull both the receipt lever and the journal lever forward and push the print anvil assembly backward (as indicated in the picture) to raise the print anvil assembly.
PP2000 (E) User’s Manual 8 - 3 Once the print anvil assembly is lifted, the paper jam can be dismissed. Please clean the paper residue in the area before putting back the print anvil assembly if the condition requires. When you are putting back the print anvil, please pay special attention to the position of the pick up reel for journal.
PP2000 (E) User’s Manual 8 - 4 However, the journal pick up reel does not automatically move forward when the print anvil assembly is put back. Please then put the journal pick up reel back to its original location, and roll the reel so that the journal remains properly tensioned.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il POSIFLEX Business Machines PP2000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del POSIFLEX Business Machines PP2000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso POSIFLEX Business Machines PP2000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul POSIFLEX Business Machines PP2000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il POSIFLEX Business Machines PP2000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del POSIFLEX Business Machines PP2000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il POSIFLEX Business Machines PP2000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo POSIFLEX Business Machines PP2000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
