Manuale d’uso / di manutenzione del prodotto Jig Saw del fabbricante Porter-Cable
Vai alla pagina of 16
T enoning Jig (Model 34-183) INSTRUCTION MANUAL P ART NO. 1342471 - 02-02-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES 1. DISCONNECT THE POWER SOURCE to the machine before attaching or adjusting the jig. 2. MAKE SURE THA T THE BLADE HAS COME TO A COMPLETE STOP befor e adjusting the jig or the workpiece.
5 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
6 6. Use the supplied 3mm hex wrench to loosen the set scr ew (M) Fig. 6. Remove the micro-adjustment assembly (N) fr om the tenoning jig (Fig. 7). M N H R P H R G Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 ADJUSTING THE GUIDE BAR TO THE T ABLE SLOT Disconnect Machine from Power Sour ce C A B Fig.
7 2. Place the tenoning jig guide bar (A) Fig. 12 into the left miter slot (D) and slide the tenoning jig back and forth to determine if it has side-to-side play . If the tenoning jig slides easily through the miter slot without side-to-side play , no adjustment is necessary .
8 Fig. 18 OPERA TION ADJUSTMENTS 1. For rapid adjustment of the work support plate (A) Fig. 19, toward or away from the saw blade, loosen levers (B) and (C) and move jig (D). Tighten levers (B) and (C). 2. Y ou can fine-adjust the work support plate (A) Fig.
9 J G P R S TENONING JIG USE This jig is intended to perform cheek cuts only . Cheek cuts are made prior to the shoulder cuts, which ar e made on a table saw using the miter gauge.
10 • The objective is to make the parts fit closely together . Maximize the gluing surface by making the tenon as long as possible (approximately 1/2 the width of the stile or longer , if using narrow stock). Balance the joint by using the same amount of wood in the tenon as in the combined thickness of the mortise walls (Fig.
11 8. Load and secure the workpiece (L) Fig. 31 on the tenoning jig and adjust the jig to perform the third and fourth cosmetic cheek cuts. Connect the machine to the power source, turn the saw “on”, and make the cuts. NOTE: When cutting the cosmetic cheek cuts, do not use the spacer block (K) Fig.
12 EXAMPLES OF MORTISE-AND-TENON JOINTS Position the wooden stop block (S) Fig. 34 in front of the saw blade to prevent the workpiece fr om being trapped between the saw fence and the saw , causing kickback. Make sure that the workpiece is clear of the wooden stop block (S) before contacting the saw blade.
13 HAUNCHED TENON CONCEALED HAUNCHED TENON MITERED TENON TENON ENDS MITERED SAW CUTS THROUGH-WEDGED TENON BARE F ACED TENON SIMPLE MORTISE AND TENON MORTISE CHEEK OF TENON SHOULDER OF TENON BLIND-WEDG.
14 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
15 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Porter-Cable Jig Saw è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Porter-Cable Jig Saw - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Porter-Cable Jig Saw imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Porter-Cable Jig Saw ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Porter-Cable Jig Saw, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Porter-Cable Jig Saw.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Porter-Cable Jig Saw. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Porter-Cable Jig Saw insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
