Manuale d’uso / di manutenzione del prodotto GSD-804 del fabbricante Planet Technology
Vai alla pagina of 20
10/100/1000Mbp s Gigabit Ethernet Switch GSD-503/GSD-504 GSD-803/GSD-804 User's Manual.
T rademarks Copyright © PLANET T echnology Corp. 2005. Content subjects to revision without prior notice. PLANET is a registered trademark of PLANET T echnology Corp.
FCC W arning This equipment has bee n tested an d found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenc e when the equipment is operated in a commercial envi ronment.
1. INTRODUCTION 1.1 Package Content s Check the conten ts of your package for following part s: 。 Gigabit Ethernet Switch x1 。 User's manual x1 。 Power adap ter x1 If any of these are missi.
1.3 Product Features 。 Complies with IEEE802.3, 10Base-T , IEEE802.3u, 100Base-TX and IEEE802.3ab, 1000B ase-T 。 IEE802.3x, full-duplex flo w control compliant; back-press ure, half-duplex flow co.
1.4 Product Specifications Model GSD-503/GSD-504 GSD-803/GSD-804 Hardware Specification Network Ports 5 10/100/1000Base-T RJ-45 MDI/MDI-X ports 8 10/100/1000Base-T RJ-45 MDI/MDI-X ports 155 x 86 x 26 mm (503) 155 x 86 x 26 m m (803) Dimensions (W x D x H) 170 x 87 x 32mm (504) 170 x 87 x 32 mm (804) Weight (KG) 0.
.
2. INSTALLATION This section describes the functi onalities of the Gigabit Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of net working is assumed. Please read this chapter completely before continui ng. 2.
This product also supports store-and-for ward forwarding scheme to ensure low latency and hig h d ata integrit y , eliminates unnecessar y traffic and relieves congestion on critical network paths.
Figure 2-5 & 2-6 show the front panel and rear panel of GSD-803 Figure 2-5 GSD-803 front panel Figure 2-6 GSD-803 rear panel Figure 2-7 & 2-8 show the front panel and rear panel of GSD-804 Figure 2-7 GSD-804 front panel Figure 2-8 GSD-804 rear panel 2.
receiving data over that port. 10 Green rating at 10Mbps. r Lit: indicate that the port is ope Blink: indicate that the switch is actively sending o receiving data over that port. ower Notice: 1. The device is a power-required device, it means, it will not work 2.
Note: When choosing a location, pleas e keep in mind the environmental restrictions discu ssed in Chapter 1, Section 1.4 Product S pecification. Step4: Connect your switch to net work devices. A. Co nn ect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the Back of the switch.
3. SWITCH OPERATION 3.1 Address T able The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the addr ess information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Swi tch.
3.4 Store-and-Forward S tore-and-Forward is one t ype of packet-forwarding techniques. A S tore-and-Forward Ethernet S witchi ng stores the incoming frame in an internal buffer , do the complete error checking before transmissi on. Therefore, no error packets occurrenc e, it is the best choice when a network needs efficiency and stability .
connection is established with another net work device (usually at Power On or Reset). This is done by detect the modes and speeds at the second of both device is connected a nd capable of, both 10Base-T and 100Base-TX devices can connect with the port in either Half- or Full-Duplex mode.
4. TROUBLESHOOTING This chapter contains information to help you solve pro blems. If Giga Switch is not functioning properly , make sure the Ethernet S witch was set up according to instru ctions in this manual.
This page intentionally left blank !.
Appendix A A.1 Switch's RJ-45 Pin Assignment s 1000Mbps, 1000Base T Cont act MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_.
RJ-45 Connector pi n assignment Contact MDI Media Dependant Interface MDI-X Media Dependant Interface - Cross 1 Tx + (transmit) RX + (receive) 2 Tx - (transmit) RX - (receive) 3 Rx + (receive) TX + (transmit) 4, 5 Not used 6 RX – (receive) TX – (transmit) 7, 8 Not used The standard cable, RJ-45 pin assignment The st andard RJ-45 recept acle/.
2010-A331 10-000.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Planet Technology GSD-804 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Planet Technology GSD-804 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Planet Technology GSD-804 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Planet Technology GSD-804 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Planet Technology GSD-804, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Planet Technology GSD-804.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Planet Technology GSD-804. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Planet Technology GSD-804 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
