Manuale d’uso / di manutenzione del prodotto PE2010 del fabbricante Planar
Vai alla pagina of 25
PE2010.
1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support.
2 The information contained in this document is subject to change without notice. This document contains proprietary info rmation that is protected by copyright.
3 TABLE OF CONTENTS For Your Safety For Your Safety ------------------------------------------------------- 4 General Notes Special notes on LCD monitors ---------------------------------------- 6 Oth.
4 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FO.
5 z Do not use the monitor near water, e.g. near a bathtub, washbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
6 GENERAL NOTES The following symptoms are normal w ith LCD monitor and do not indicate a problem. • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
7 GENERAL NOTES (cont.) • Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identit y and, depending on the level of DDC used, communicate additional information about its display capabilities.
8 BEFORE YOU OPERATE THE MONITOR • 20” (51cm) TFT Color LCD Monitor • Crisp & Clear Display for Window s • Recommended Resolution: 1400 X 1050 @ 60Hz • Ergonomic Design with Tilt Adjusta.
9 INSTALLATION INSTRUCTIONS Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.
10 INSTALLATION INSTRUCTIONS (cont.) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 2. 15-pin D-SUB Cable 3. DVI Cable Turn off your computer befor e performing the procedure below . 1. Connect the female end of the AC pow er cord to the AC-in port on the back of the monitor.
11 INSTALLATION INSTRUCTIONS (cont.) ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to l ook at the full face of the monitor, then adjust the monitor's angl e to your ow n preference. Hold the stand so you do not toppl e the monitor w hen you change the monitor's angle.
12 OPERATING INSTRUCTIONS (cont.) EXTERNAL CONTROLS Figure 4 - External Controls 1. SOURCE 5. Menu / Enter 2. Auto Config / Exit 6. Power Indicator 3. ∧ /ECO changing 7. Power Button 4. ∨ / Bri / con • Pow er Button: Press this button to turn the monitor ON or OFF.
13 OPERATING INSTRUCTIONS (cont.) • Auto Adjust button / Exit: 1. When OSD menu is in active stat us, this button will act as EX IT-KEY (EXIT OSD menu) or go back to the previous menu. 2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function.
14 OPERATING INSTRUCTIONS (cont.) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 5). 2. Press ∧ or ∨ to navigate through the functi ons. Once the desired function is highlighted, press the MENU-button to activate it.
15 OPERATING INSTRUCTIONS (cont.) ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital- register.
16 OPERATING INSTRUCTIONS (cont.) Analog N/A Select input signal from analog source (D-Sub) Input Select Digital N/A Select input signal from digital source (DVI) H. Position Adjust the horizontal position of the OSD. 50 V. Position Adjust the vertical position of the OSD.
17 TECHNICAL SUPPORT (FAQ) (cont.) Problem & Question Possible Solution Power LED is not on *Check if the Power Sw itch is in the ON position *Power Cord should be connected No Plug & Play *Ch.
18 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal.
19 APPENDIX SPECIFICATIONS Driving system TFT Color LCD Size 51cm(20") Pixel pitch 0.2916mm( H )x 0.2916mm( V ) LCD Panel Viewable angle 160 ° (H) 160 ° (V) R,G,B Analog Interface Video Digital interface H-Frequency 30KHz – 82Hz Input V-Frequency 60 -75Hz Display Colors 16.
20 APPENDIX (cont.) Switch • Source • Auto Config / Exit • ∧ / ECO • ∨ / Bri/Con • Menu / Enter • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
21 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) IBM DOS 720 × 400 31.47 70.0 640 × 480 31.47 60.0 VGA 640 × 480 37.50 75.0 800 × 600 37.879 60.0 SVGA 800 × 600 46.875 75.0 1024 × 768 48.
22 APPENDIX (cont.) Connector Pin Assignment 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6.
23 APPENDIX (cont.) 24 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. TMDS Data 2- 13. T MDS Data 3+ 2. TMDS Data 2+ 14. +5V Power 3. TMDS Data 2/4 Shield 15. Ground(for+5V) 4. TMDS Data 4- 16. Hot Plug Detect 5. TMDS Data 4+ 17.
Q41G2002935 1B 1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com © 2006 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Planar PE2010 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Planar PE2010 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Planar PE2010 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Planar PE2010 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Planar PE2010, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Planar PE2010.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Planar PE2010. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Planar PE2010 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
