Manuale d’uso / di manutenzione del prodotto PE1900 del fabbricante Planar
Vai alla pagina of 32
PE1900.
.
1 Contents Introduction .......................... ..................... ...................... ................. ..... 2 Features .................... ................ .................... .................... .................... ...................
2 Introduction The PE1900 LCD monitor has a 19-i n ch active matrix TFT (thin film transistor) liquid crystal display module. It is designed for use with any W indows ® -based PC. Featur es Ö Automatic configura tion to the PC video set tings with maximum SXGA resolution.
3 If any of the following conditi ons occur , unplug the display and contact qualif ied service personnel: Ö The power cord or plug is frayed or damaged. Ö Y ou have spilled liquid into the display . Ö The display has b een exposed to rain or wat er .
4 Installation Please follow the instructions in this chapter to install your LCD Monitor . Note: Befor e connecting your display, first r ead th rough the instructions in this chapter and the safety precautions in the pr evious chapter .
5 The functions of the three contr ol buttons which are located at the lower left side of the f ront panel of your display are descri b ed as below: Button Function Descriptio n Select (1) Turn on OSD menu while it is off. (2) Execute the function selected in the OSD men u.
6 4. Plug the analog vi d eo signal ca ble into the Analog V ideo Input port on the bac k of the display (as shown above) . 5. Connect the other end of the v ideo cable into you r computer’ s video port. (Please check your computer’ s documentation if you’re no t sure where the port is located.
7 Using Y our Display This chapter contains inform ation about using your LCD M onitor . T urning the Display On and Off Use the power button locat ed at the lower right side of the front panel of the display t o turn the display on and off. When the display is on, the light (LED) near the Power button is illuminated.
8 T ilting the Display The monitors have a tilt f e ature that allows yo u to tilt the display back and fort h to find the most comfortable viewing position. T o tilt the display , grasp the sides an d push the display back or pull it toward you, or turn it left or right unti l it is in the desired p osition.
9 The table in “V ideo Mode” on p age 27 shows the image ref resh rates supported by the dis play at dif ferent screen resol ution. Although your LCD monitor s upports up to 75 Hz for a nalog video input, we recommend t hat you use 60 Hz refresh ra te for best perform ance.
10 Note: If the screen is still dirty , you can dampen th e cloth with se veral drops of dist illed water . Make sur e the LCD panel is completely dry be fore you turn the display back on.
11 Adjusting Y our Display This chapter contains inform ation about how to c hange display settings f or your LCD Monitor . It is designed with an OSD men u to help you easily adj ust to its optimum performance. Note: Y ou must perform auto-setup befor e making any adjustments.
12 Item Description Auto Adjust the “Auto Setup” . See “Adjusti ng Auto Setup” on page 12. Management Open the “ Management ” subm enu to select Brightne ss, Contrast or Im age Position for further adjustment. Se e Adjustment in the “ Management” Submenu on pa ge 13.
13 3. Use ‘ Select ’ button to select and execute the Auto Setup function. After the execution of the Auto Setup function, it w ill show the following message: If the image looks corr ect, choose ‘ Ye s ’ . OR If the image requires furt her adjustment, choose No .
14 3. Use ‘ Select ’ key to en ter the “Manag ement” Sub m enu. This activates four items for adjustment. If ‘Brightness’ is selected, use ‘ Up ( △ ) ’ o r ‘ Down ( ▽ ) ’ buttons to adjust the setting of brightness. The graphic bar and numerical value at the right corner respond s according ly .
15 responds accordingly . If ‘V . position’ is selected, use ‘ Up ( △ ) ’ o r ‘ Dow n ( ▽ ) ’ buttons to adjust the setting of the vertical posit ion of the image. The graphic ba r a nd numeric al value at the right corner responds accordingl y .
16 Adjusting the “Clock/Phase” Submenu Follow the steps bel ow to adjust the “Clock/Phas e” submenu: 1. Activate the OSD “ Main Menu ”. 2. Use ‘ Up ( △ ) ’ ( o r ‘ Down ( ▽ ) ’) to move forwar d (or backward) to the clock/ phase icon and highlight it.
17 Adjusting the “Color” Sub menu Follow the s teps below to adjust the “ Color” submenu: Activate the OSD “ Main Menu ”. 1. Use ‘ Up ( △ ) ’ ( o r ‘ Dow n ( ▽ ) ’) to move forward (or backwar d) to the color icon and highlig ht it.
18 Note: As you choose an item, your scr een im mediately updates to r eflect this setting. Selecting ‘Black Level Adjust’ activates the “ Back Lev el A djus t ” submenu. Adju st its settin g by using the ‘ Up ( △ ) ’ a n d ‘ Down ( ▽ ) ’ buttons.
19 Adjusting the “O SD Display” subm enu Follow the s teps below to adjust the OS D Horizontal and V ertical positions: 1. Activate the OSD “ Main Menu ”. 2. Use ‘ Up ( △ ) ’ ( o r ‘ Down ( ▽ ) ’) to move forward (or backward ) to the OSD display ico n and highlight it.
20 Select ‘Exit’ to exit the “OSD Di spla y” subme nu and r eturn t o the “ Main Menu ”. Adjusting the Factory Recall T o recall factory settings back y ou should follow the steps below: 1.
21 Selecting your preferred Language Follow the s teps below to select one of the five languages: 1. Activate the OSD “ Main Menu ”. 2. Use ‘ Up ( △ ) ’ ( o r ‘ Down ( ▽ ) ’) to move forwar d (or backward) to the langua ges icon and highlight it.
22 Using the Direct Keys There are two direct keys that f u nction while OSD “ Main Menu ” is inactivated: “Auto-Set up” and “ Brightness.” Using the “Auto Setup ” Direct Ke y Use Auto-Se tup wheneve r you apply a new video mod e or change the re fresh rate.
23 If the image requires furt her adjustment, choose No , and the ‘Phase’ bar is activated for further manual adjus tment. Adju st the ph ase us ing ‘ Up ( △ ) ’ o r ‘ Dow n ( ▽ ) ’ buttons. When all text appears well-f ocused and the image is stable, pre ss the ‘ Select ’ key to end the adjustment and close the OSD menu.
24 T roubleshooting This chapter contains informatio n about how to troubleshoot your LCD M onitor . If you have tried all o f the it ems l isted below , plea se con tact qu alifie d ser vice pe rsonn el. A. My display doesn’ t work, even though the compu ter appears to work.
25 E. The imag e is very unstable. 1. Set your PC to a supp orted vi deo mode, preferably 1280 x 1024 at 60 Hz . See “Sett ing the V ideo Mode” on page 8. 2. Restore the original factory settings by choosing Factory Recall in the OSD “ Factory Recall ” submenu.
26 T echnical Information This chapter contains technical in formation about your LCD Monitor . Display Information LCD Module 19-in, active m atrix TFT , anti-glare coating, 0.2 94 mm pixel pitch. Display Size 14.8 (H) x 11.9 (V) in ches. V iewing Angle Left / Right Up / Down -85 ° / 85 ° (T ypical).
27 V ideo Mo des Y our LCD monitor su pports the following i ndustry-standar d combinations of screen resol u tion and refresh rates. Other c ombinations are possible, but m ay require adjustments to the ima ge. For optimum performance, set your PC to a screen res olution of 1280 x 1024 at a 6 0 Hz refresh rate.
28 Regulatory Information Agency Approvals European USA Japan Others CE UL Safety CSA Emissions FCC Class B .DOC Immunity Ergonomic EP A Y E S FCC Statem ent: FCC Notice – Part 15 This device complies with Part 15 of FCC rule s. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
.
PLANAR SYSTEMS, INC. Customer Service support: http://planar .custhelp.com email: desktopmonitors@planar .com phone: 1-866-PLANAR-1 (1-866-752-6271) hours: M-F , 8am - 9pm EST @ 2004 Planar Systems, Inc. Planar is a registered tr ademark of Planar Systems, Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Planar PE1900 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Planar PE1900 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Planar PE1900 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Planar PE1900 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Planar PE1900, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Planar PE1900.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Planar PE1900. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Planar PE1900 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
