Manuale d’uso / di manutenzione del prodotto 35C+ del fabbricante Pitco
Vai alla pagina of 41
Installation, Operation, and Maintenance Manual For Gas Fryers Covering Models 45C+, 35C+ and 40C+ Pitco Frialator, Inc., P.O. Box 501, Jct I-89 & I-93 Concord, NH 03302-0501 • 509 Route 3A, Bow.
Pitco Frialator #L20-072 Rev 6 (05/11).
NOTICES There are three different types of notices that you should be familiar with, a NOTICE, CAUTION, and WARNING. A NOTICE is a special note used to call attention to a particularly important point. CAUTION is used to point out a procedure or operation which may cause equipment damage.
SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY WARNING The cooker must be electrically grounded in accordance with local codes. If local codes do not apply, follow the requirements of National Code ANSI/NFPA 70-1990. WARNING This cooker is equipped with a three prong safety plug.
SAFETY SAFETY SAFETY SAFETY SAFETY THIS MANUAL MUST BE RET AINED FOR FUTURE REFERENCE SAFETY SAFETY SAFETY SAFETY SAFETY WARNING Carbon monoxide can build up if the flue is blocked. Blocking the flue will also cause the cooker to overheat. Ensure that minimum clearances specified in the installation instructions are maintained.
.
i T able of Content s Section Title Page Table of Contents ............................................................................................................................................ i List of Tables and Fig ures .....................
ii List of T ables and Figures Table Title Page 1 - 1 Fryer Model Information ................................................................................. 1 - 1 1 - 2 Ventilation and Fire Safety References ........................................
1-1 Chapter 1: General Information and Installation Congratulations on the purchase of your new Pitco Frialator universal fryer. This unit will give you many years of reliable service if you follow the simple operation and maintenance procedures in this manual.
1-2 Locate your Pitco Frialator warranty and fill in the serial number of the fryer and the date received. You will find the serial number on the plate inside the door. Put your warranty card in a safe place for future reference. DO NOT return the card to Pitco Frialator.
1-3 1.3.2 Assembling Multi Fryer Systems If you purchased a multi-fryer unit, it could be shipped in more than one piece. To assemble the unit follow the instructions below. a . Unpack the units and move them close together. Remove the front panels and both heat shields from the fryers.
1-4 Code (NFPA 54-Latest Edition) and ANSI Z223.1-Latest Edition Latest Edition. In Canada, install the fryer in accordance with CAN/CGA-B149.1 or .2 and local codes. Gas line sizing requirements can be determined by your local gas company by referring to National Fuel Gas Code, Appendix C, Table C-4 (natural gas) and Table C-16 (propane).
1-5 1.4.2.4 Fuel Supply Line Leak and Pressure Testing - The fuel supply system must be tested before the fryer is used. If the fuel line is going to be tested at a pressure greater than (>)1/2 PSIG (3.45 kPa), make sure that the fryer is disconnected from the fuel line.
1-6 1.5.1 Visual Checks After the fryer is in its permanent location, lock the casters and check for levelness. Any additional leveling that is necessary can be performed as described in section 1.3. 1.5.2 Burner Ignition Systems CAUTION Before going any further, fill the fryer with WATER.
1-7 To light the pilot light, refer to these instructions. WARNING Wait 5 minutes before attempting to relight the pilot to allow for any gas in the fryer to dissipate. a . Open the gas supply valves to the fryer. b . Open the fryer's door to gain access to the controls.
1-8 c . Connect the negative (-) test probe to pilot bracket. d . Connect the positive (+) test probe to to one of the High Limit terminal connections e . Remove the pilot flame adjustment cover. f. Turning the flame adjusting screw clockwise lowers the flame and the millivolt output.
1-9 a . Ensure that the Unitrol valve knob is in the OFF position. Remove the manifold pressure tap plug and connect an accurate pressure gauge (range of 0-16" w.c. in 0.1" increments) or manometer. b . Light the pilot burner (see 1.5.2) for the unit being tested and adjust the thermostat to light the main burners.
1-10 a . Fill the tank with water and add one packet of Pitco fryer cleaner or a mild detergent. b . Turn the fryer on and set the thermostat to 200°F. Allow the fryer to heat for 15 minutes. NOTICE Do not leave the fryer unattended during cleaning. Never let the water level go below the "Min Level" mark on the back of the tank.
1-11 b . Set the thermostat at 325°F and wait for the temperature reading on the thermometer to rise. As the temperature rises toward 325°F watch the thermometer closely. c . If the shortening temperature reaches 350°F and the burners DO NOT turn off, turn the thermostat down.
1-12.
2-1 Chapter 2: Operating Instructions This chapter describes how to operate your fryer to obtain the best performance. Included in this chapter are filling, operating, and cleaning instructions for gas fryers. 2 . 1 FILLING THE FRYER Both liquid and solid shortening can be used in the fryer, but liquid is preferred.
2-2 2 . 2 OPERATING INSTRUCTIONS To ensure the food always comes out the very best, follow the preparation instructions for the food you are cooking. Using the best shortening makes the best fried foods. The best shortening will last longer than lower grade shortening and save you money.
2-3 e . Wait 30 seconds. f . Repeat steps c. through e. until the shortening is melted. g . Set thermostat to normal operating temperature. The burners will remain on constantly until the shortening temperature reaches the thermostat setting. h . Once at temperature, the fryer is now operating normally and ready to use.
3-1 Chapter 3: Owner Maintenance and Adjustment s This chapter provides you with the information and procedures necessary to perform basic fryer maintenance and adjustments. If, after performing maintenance on your fryer, it does not perform properly, contact your authorized service center.
3-2 3 . 3 TROUBLESHOOTING This section is provided to aid you in the event of fryer or filter troubles. If these troubleshooting procedures do not correct your problem contact a qualified technician or the factory. The troubleshooting procedures are in a flowchart format.
3-3.
3-4 ENGLISH.
In the event of problems with or questions about you equipment, please contact the Pitco Frialator Autho- rized Service and Parts representative (ASAP) cov- ering you area, through Pitco Frialator , Inc. In the event of problems with or questions about you order , please contact the Pitco Frialator factory , from 8:00 a.
Manuel d’installation, d’utilisation et d’entretien pour friteuses à gaz Modèles 45C+, 35+C et 40C+ Pitco Frialator, Inc., P.O. Box 501, Jct I-89 & I-93 Concord, NH 03302-0501 • 509 Rout.
i Tables des matières Section Titre Page Table des matières.................................. ..................................................................................................i Liste des tableaux et figures .........................
ii Liste des tableaux et figures Tableau Titre Page 1-1 Informations relatives à ce modèle de friteuse ............................................................................... 1-1 1-2 Références pour la ventilation et les consignes de sécurité incendie .
Pitco Frialator #L20-072 Rev 6 (05/11).
1-1 Chapitre 1: Information d’ordre général et installation Félicitations! Vous venez de faire l’acquisition d’une friteuse universelle Pitco Frialator. Cette machine vous offrira des années de fonctionnement fiable si vous suivez les instructions d’utilisation et d’entretien de ce manuel.
2-1 Chapitre 2: Instructions de fonctionnement Ce chapitre décrit comment utiliser la friteuse pour un rendement optimal. Vous y trouverez des instructions sur le remplissage, l’utilisation et le nettoyage des friteuses à gaz.
2-2 2. 2 INSTRUCTIONS DE FONCTIONNEMENT Afin que la nourriture soit toujours parfaitement cuite, suivez les instructions de préparation concernant les aliments que vous comptez frire. Utilisez la meilleure matière grasse possible afin d’obtenir les meilleurs aliments frits.
2-3 e. Attendez 30 secondes.. f . Répétez les étape C à E jusqu’à ce que la matière grasse ait fondue. g . Réglez le thermostat sur la température de fonctionnement normale. Les brûleurs demeureront allumés en continu jusqu’à ce que la température de la matière grasse atteigne la température consignée du thermostat.
3-1 Chapitre 3: Entretien et réglages à effectuer par le propriétaire 3-1 Ce chapitre vous offre des informations et des instructions nécessaires afin de procéder à l’entretien de la friteuse et ses réglages.
3-2 3. 3 GUIDE DE DÉPANNAGE Cette section est destinée à vous aider si avez des problèmes avec la friteuse et avec les filtres. Si les mesures correctives ne règlent pas le problème, contactez un réparateur qualifié ou l’usine. Les mesures correctives sont offertes sous forme de diagramme.
3-3.
3-4 FRANCAIS.
V euillez contacter votre représentant agréé Pitco Frialator si vous avez des problèmes ou des questions concernant votre équipement par l’intermédiaire du réseau de service après-vente nati.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pitco 35C+ è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pitco 35C+ - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pitco 35C+ imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pitco 35C+ ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pitco 35C+, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pitco 35C+.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pitco 35C+. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pitco 35C+ insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
