Manuale d’uso / di manutenzione del prodotto DX8000 del fabbricante Pelco
Vai alla pagina of 40
DX8000 Hard Drive Upgrade Installation For Single Drive Systems C1606M (6/04) Digital Video Recorder DX8000.
Protecting people and property in a million locations worldwide..
C1606M (6/04) 1 Introduction The following instructions serve as a guide for replacing the primary hard disk drive of your DX8000 Series digital video recorder (DVR). Step-by-step directions show you how to install the DX8000-UP250 hard disk upgrade kit.
2 C1606M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools.
C1606M (6/04) 3 Figure 2. Removing Power Cord from Unit.
4 C1606M (6/04) Figure 3. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit.
C1606M (6/04) 5 Prepare Unit for Drive Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components.
6 C1606M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section.
C1606M (6/04) 7 COMPONENT LA YOUT Figure 5 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustration in this manual for the purpose of clarity .
8 C1606M (6/04) Move the Front Cross-Brace 1. Unscrew and lift out the front cross-brace (found at the center of the unit). Moving this part out of the way will make it easier for you to access the hard drive mounting baskets. a. Use a Phillips-head screwdriver to remove the two flat-head screws that secure the front cross-brace.
C1606M (6/04) 9 b. Carefully place the cross-brace and fan across the rear section of the unit. Refer to Figure 7. WARNING: Do not disconnect the wires or remove the front cross-brace entirely from the unit— doing so may cause damage to the fan’ s power connection.
10 C1606M (6/04) Disconnect the Data and Power Cables When removing the data and power cables, pull the connectors straight out. Do not rock connectors back and forth or remove a cable by pulling it by its wires or cable. 1. Remove the IDE data cable from the existing hard drive, CD-RW drive, and motherboard: a.
C1606M (6/04) 11 2. Remove the power connectors from the hard drive. HARD DRIVE POWER CONNECTOR Figure 9. Removing Hard Drive Power Connection.
12 C1606M (6/04) Remove the Drive Mount Basket 1. Remove the first hard drive mounting basket: a. Using a Phillips-head screwdriver , unfasten and save the four screws that attach the drive basket to the chassis. Refer to Figure 10. b. Gently lift the basket up and out with the drive attached.
C1606M (6/04) 13 Replace the Primary Hard Disk NOTE: This upgrade kit includes a Pelco-certified hard disk drive. Using any other hard disk drive with the DX8000 voids the manufacturer’ s warranty for this product. REMOVE THE ORIGINAL DRIVE 1. Using a Phillips-head screwdriver , unfasten the screws attaching the drive to the basket.
14 C1606M (6/04) MOUNT THE NEW DRIVE 1. Mount the new drive in the drive basket. Use the drive slot closest to the CD-RW drive. Refer to Figure 12. a. Make sure the drive is mounted in the basket so that access to the connectors is not blocked. b. Attach the drive to the basket using the two screws that came with the upgrade kit.
C1606M (6/04) 15 2. Mount the drive basket back into the chassis: a. Align the basket and press down firmly to ensure that it fits flush against the top of the chassis bracket. Refer to Figure 13. b. Secure the drive basket to the chassis using the four screws you set aside earlier .
16 C1606M (6/04) DATA CONNECTOR MASTER/SLAVE JUMPERS POWER CONNECTOR PIN 1 SET THE MASTER / SLA VE JUMPER Each hard drive must be configured as either a master or slave device to operate correctly . A jumper is used to configure a pair of connected hard drives to operate in a master/slave relationship.
C1606M (6/04) 17 MASTER CD-RW FRONT OF DVR JUMPER SLAVE SETTING MASTER SETTING Figure 15. Setting Drive Jumper.
18 C1606M (6/04) RECONNECT THE DA T A AND POWER CABLES IMPORT ANT : Data and power cable connectors fit together only one way . All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard, and cable connectors before installation so that connectors are properly aligned.
C1606M (6/04) 19 1c 1b 1 a Figure 16. Installing CD-RW and Hard Drive Data Cable.
20 C1606M (6/04) 3. Connect the hard drive power connector according to the diagram in Figure 17. Figure 17. Installing Power Connector HARD DRIVE POWER CONNECTOR.
C1606M (6/04) 21 Reassemble the Unit 1. Replace the front cross-brace and secure it with the flat-head screws you set aside earlier . Refer to Figure 18.
22 C1606M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 19. Figure 19. Replacing Chassis Cover.
C1606M (6/04) 23 ON/OFF 3. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 4. Plug the power cord back into the power supply and then into the wall. 5. T urn on the power switch and allow the unit to start up and find the new hard disk.
24 C1606M (6/04) Install Software on the New Drive To complete the installation of a new primary hard disk in your DX8000, all necessary operating system and application software must be installed. Installation of this software will require that you configure the DX8000 to boot from the CD/DVD drive.
C1606M (6/04) 25 3. Press the Delete key on the keyboard as the system is booting and before the Windows ® operating system loads. The BIOS main screen appears.
26 C1606M (6/04) 4. If you receive a prompt requesting that you enter a password, contact your system administrator for assistance logging into and changing the DX8000 BIOS Setup. 5. Use the cursor control (arrow) keys on your keyboard and move right to the Boot option in the Main screen.
C1606M (6/04) 27 7. Press the F10 function key on your keyboard to save and exit the BIOS setup screen. 8. Finalize BIOS changes: •T o accept the boot sequence changes and reboot, press the Enter key . •T o cancel the changes, press the Esc key and then press Ctrl+Alt+Delete keys simultaneously to reboot.
28 C1606M (6/04) INST ALL SOFTW ARE 1. The DX8000 Recovery dialog box appears. Figure 23. DX8000 Recovery Dialog Box 2. Carefully read the warning presented in the dialog box and type the word Ye s to confirm that you want to continue the reinstallation process.
C1606M (6/04) 29 4 Figure 24. Partition Size Verification Dialog Box 4. Click Y es. The Proceed with Disk Restore dialog box appears. CAUTION: Proceeding with the recovery procedure will permanently overwrite the software and data stored on your system’ s C: drive.
30 C1606M (6/04) Figure 25. Proceed with Disk Restore Dialog Box 5. Click Y es. A progress bar appears reporting the progress of the system installation.
C1606M (6/04) 31 7. Press the Delete key on the keyboard as the system is booting and before the Windows operating system loads. The BIOS main screen appears.
32 C1606M (6/04) 10. Press the minus (-) key on your keyboard to change the boot sequence from the CD/DVD drive back to the hard disk. The screen should look something like the example in Figure 28. AwardBIOS Setup Utility 1. IDE Hard Drive 2. 3. Other Boot Device 4.
C1606M (6/04) 33 Initialize the New Drive 1. While the DX8000 starts, the built-in setup program will automatically detect the newly installed drive and reconfigure the basic settings of the unit to make use of the increased storage capacity . No action by the user is necessary during this step.
34 C1606M (6/04) b. Click the Not Used button. Refer to Figure 30. A drop-down menu appears. 3b 3c Figure 30. Opening Drive Option Menu c. Select the Allocation option from the drop-down menu.
C1606M (6/04) 35 3e 3d d. Click Begin Allocation. Figure 32. Initializing Drive Allocation e. The Formatting dialog box appears. Click Start. Figure 33.
36 C1606M (6/04) f. Wait while the DX8000 prepares the newly installed drive for video storage. Y ou will see the following progress bar while the formatting is underway .
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco DX8000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco DX8000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco DX8000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco DX8000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco DX8000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco DX8000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco DX8000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco DX8000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
