Manuale d’uso / di manutenzione del prodotto C2406M-F (4/04) del fabbricante Pelco
Vai alla pagina of 16
200 Series Camclosure ® Integrated Camera System C2406M-F (4/04) ® INST ALLA TION/OPERA TION.
2 C2406M-F (4/04) IMPORT ANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C2406M-F (4/04) 3 DESCRIPTION The wedge style 200 Series Camclosure ® integrated camera system is designed to mount directly to a wall or ceiling. It also can mount to a corner with the ICS200-CM corner mount. The system incorporates a camera and lens package into a small, medium security enclosure.
4 C2406M-F (4/04) INST ALLA TION The following parts are supplied: 1 Camclosure integrated camera system 1W atertight mounting plate 1 1/8-inch pin-in-hex Allen wrench bit 3 10-32 x 0.5-inch Phillips screws 3 #10 internal tooth lock washers 1 Hole plug PREP ARE MOUNTING SURFACE 1.
C2406M-F (4/04) 5 INST ALL BASE WITHOUT CONDUIT 1. Outdoor Installation Only – Bring the power and video wiring for the camera through the wiring hole in the watertight mounting plate. Then fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length.
6 C2406M-F (4/04) bottom of the base (refer to Figure 5). Pull the wiring inside the base. WARNING: Be careful not to damage the wiring or the connection where the video cable is fastened to the circuit board. 3. Using the screwdriver bit that is provided, remove the conduit cover and plate by unscrewing the tamperproof screw .
C2406M-F (4/04) 7 REINST ALL CAMERA MODULE 1. Reinstall the camera module. Refer to Figure 8. Make sure the top of the camera is oriented properly . On the lens housing, look for the label that says TOP . WARNING: To prevent damage to the camera or lens, the camera must be installed in the proper hole of the mounting bracket.
8 C2406M-F (4/04) ADJUSTMENTS (COLOR CAMERA ONL Y) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary . 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit.
C2406M-F (4/04) 9 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, do the following: 1. Loosen the locking screw on the bottom of the lens. T o loosen the screw , it may be necessary to remove the heater board. Refer to Figure 14 and the accompanying steps.
10 C2406M-F (4/04) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to Figure 16. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details.
C2406M-F (4/04) 11 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for optimal performance in lighting conditions where auto iris is required. It is also configured with the shutter speed set at 1/60 (NTSC) or 1/50 (P AL) and AGC set at 6 dB of gain.
12 C2406M-F (4/04) (Design and product specifications subject to change without notice.) SPECIFICA TIONS General Pan/T ilt Adjustment: Manual; ± 10 ° pan; 5 ° above horizontal to 20 ° below horizo.
C2406M-F (4/04) 13 REGULA TORY NOTICES FCC Class A (monochrome, EIA cameras only) This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules.
14 C2406M-F (4/04) W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
C2406M-F (4/04) 15 REVISION HISTORY Manual # Date Comments C2406M 11/99 Original version. 1/00 Revised installation instructions. Added FCC notices. C2406M-A 2/00 Added varifocal lens. Changed format. C2406M-B 11/00 New camera module design, revised installation instructions.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco C2406M-F (4/04) è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco C2406M-F (4/04) - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco C2406M-F (4/04) imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco C2406M-F (4/04) ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco C2406M-F (4/04), ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco C2406M-F (4/04).
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco C2406M-F (4/04). Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco C2406M-F (4/04) insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
