Manuale d’uso / di manutenzione del prodotto C1302M-F (11/08) del fabbricante Pelco
Vai alla pagina of 24
INSTALLATION C1302M-F (11/08) ExSite ® Series Explosionproof Pan and T ilt Sy stem.
2 C1302M-F (11/08).
C1302M-F (11/08) 3 Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started .
4 C1302M-F (11/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any ven tilation openings. Ins tall in accordance with the manu facturer’ s instructions.
C1302M-F (11/08 ) 5 Getting Started Thank you for purcha sing Pelco’ s ExSite ® Series explosionproof integrated positioning system. This manual i ncl udes instructions for installing all the componen ts of the E xSite Series sy stem.
6 C1302M-F (11/08) Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (220 lb /100 kg).
C1302M-F (11/08 ) 7 CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is allocated specific ally for an external washer (not supp lied by Pelco ). • All relays ar e specified fo r 32 VDC, 0.
8 C1302M-F (11/08) DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are re quired for Coaxitron contr ol.
C1302M-F (11/08 ) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON O.
10 C1302M-F (11/08) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OF F 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF O.
C1302M-F (11/08 ) 11 T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF.
12 C1302M-F (11/08) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON .
C1302M-F (11/08 ) 13 Install the Camera Module T o install the camera mo dule do t he following: 1. Refer to Figure 4. Loosen the set screw at the ba ck of the enclosure with the provided 1.5 mm Alle n wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanne r wrench to loosen the ba ck of the camera enclosur e (refer to Figure 5).
14 C1302M-F (11/08) 3. Slide th e camera modul e into the enclosure. Ref er to Figur e 6 to posi tion the camera module pr operly in the enclosure . Careful ly mate the camera’ s po wer connector to the ma ting connector locat ed inside the enclosur e.
C1302M-F (11/08 ) 15 4. Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the su pplied gree n bushing on the stud l ocated be hind the ha ndle of the camera module . The bushin g should be in the sam e orientatio n as shown in Figure 8.
16 C1302M-F (11/08) Install the Pan and T ilt Unit 1. Check fo r proper se ating of t he power modu le seal. Make sure the se al is fully seated in t he groove o n the top of the powe r m odule. Figure 9. Factory-Installed Power Module Seal 2. Refer to Figure 10 an d attach t he pan and tilt unit to the power mo dule.
C1302M-F (11/08 ) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 11. 2. Align the moun ting holes of the sun shrou d with the holes on top o f the enclosure. 3. Use the su pplied nyl on washers an d screws to se cure the su n shroud to the enclosu re.
18 C1302M-F (11/08) Maintenance CAMERA MODULE REPLACEMENT T o replace t he camera mod ule do th e following: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 12 and do the following: a. Loosen the set screw with a 1 .5 mm Allen wren ch.
C1302M-F (11/08 ) 19 3. For mo dels with wiper s, also re move the wiper a rm and the g reen bus hing from th e unit (see F igure 13) . 4. Slide the camera module out of the enclosure. 5. Install the new camera mo dule by doin g the follo wing: Slide the camera module into the enclo sure.
20 C1302M-F (11/08) 6. Refer to Figure 13 an d do the foll owing to r einstall the ar m of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module. b. Reinstall the wiper arm. Pl ace the ridg e of the a rm in the n otch of th e enclosure tab and the slot of th e arm ov er the gre en bushing.
C1302M-F (11/08 ) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input V olt age Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Electrical Connections 6-foot wire harness with c onnections for power , video, da ta control, alarm inputs , and auxiliary outputs MECHANICAL Cable Entry One 0.
22 C1302M-F (11/08) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT 9500 control lers, but not with CM75 00, MPT9000, o r KBD9000 contr ollers.
The materials used in the manufacture of this documen t and it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
Pelco, Inc. Worldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco C1302M-F (11/08) è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco C1302M-F (11/08) - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco C1302M-F (11/08) imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco C1302M-F (11/08) ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco C1302M-F (11/08), ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco C1302M-F (11/08).
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco C1302M-F (11/08). Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco C1302M-F (11/08) insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
