Manuale d’uso / di manutenzione del prodotto Monarch 415 del fabbricante Paxar
Vai alla pagina of 28
Monarch 415 TM Rewind Operator’ s Handbook TC0415OH Rev. D 5/96 ©1990-96 Monarch Ma rking Systems, Inc. All rights reserved..
Each product and program carries a respectiv e writ ten warranty , the only warr anty on which the customer can rely . Monarch reser v es the right t o mak e changes in the product and the programs and their av ailability at any time and without notice.
Table of Conten ts 1. Setting Up ...... ........ ........ ...... ........ .......... ........ ........ ...... ...... 1 2. Connecting Supplies ...... ........ ........ ...... ........ .......... ........ .. 3 Rewinding on the Hub ..... ...... ...... ..
Monarc h 415 Rewind Operato r ’ s Ha ndbook ii.
1. Setting Up 1. Push the 415 Rewind pow er s witch OFF . 2. Place the re wind on a le vel surf ace. Be sur e it is at least ten inches a wa y from the supply e xit of the printer (Figure 1). 3. Squarely align the rewind’ s hub flange with the edge of the supply .
4. Plug the power cord into the rewind ( Figur e 2). Then, plug the pow e r cord into a grounded elec tr ical outlet. Figure 2 Po w e r Cor d Po w e r Switch Fuse Holder Monarc h 415 Rewind Operato r .
2. Con necting Suppli es Rewinding on the Hub 1. Slide the supply guide a wa y from the hub flange and pull it aw ay from the hub. 2. Print or f eed enough supplies from the pr inter to wrap around the hub one and one half times. 3. Hold the hub flange and twist the hub cl o ck wi se until it stops.
6. T ur n the hub and hub flange at leas t one full turn counterc lockwise to tighten the supply strip . 7. Push the supply guide against the hub then slide it against the supply . NOTE: Units with 3" hubs ha ve a flanged disk instead of a supply guide .
Rewinding on a P aper Core 1. Slide the supply guide a wa y from the hub flange and pull it aw ay from the hub. 2. Push the paper core on t he hub until it is against the hub flange. 3. Hold the hub flange and twist the hub cl o ck wi se until the paper core is tight.
5. T ur n the hub and hub flange at leas t one full turn counterc lockwise to tighten the supply strip . 6. Push the supply guide against the hub then slide it against the supply .
3. Operating the Rewind Starting 1. T ur n the speed control knob ( Figure 6) to SLO W . 2. Push the rewind pow er s witch (Figure 7) ON . NOTE: The rewind will star t to tur n. When the dancer roller is almost horizontal, the rewind will stop. 3. Star t t he printer .
Stopping 1. Stop the pr inter . 2. Push the rewind pow er s witch OFF . 3. Pull the supply guide a wa y from the hub . 4. Cut the supply at the s upply e xit of the pr inter (Figure 8). 5. T ape the end of the supply to the r oll on the rewind. 6. Pull the supply guide a wa y from hub .
4. Ch anging Hubs If y ou change to a diff er ent supply , you may need to use a diff er ent hub . One, three , and f our inch diam eter hubs (shor t and long) are a vailab le from Monarch. T o change hubs 1. Pull the supply guide a wa y from the hub (Figure 9) .
3. Remov e the hub sections and replace them with the new ones (Figure 11). a. Slide the new hub spindle on t he shaft. Be sure the notch fits over t he raised portion of the hub flange. b. Slide the hub sections on t o the shaft with t he open ends facing out.
5. Burster Option Setup and Operation Proper positioning of t he printer , burster , and supplies is critical. 1. Place the Rewind/Burster assemb ly in the proper position in front of the pr inter . A dra wing showing the correct position f or all suppor ted pr inters and optional location guides f or alignment is inside the bac k co ver .
4. Figure 13 shows the b urster with the supplies installed. Place the separator bars in their approxim ate working positions (i.e. in line with t he perf orations). When only one bar is needed (f or two par t supply), slide un used bar to the outboard side.
8. Slide the first core onto the 415 hub until it is against the hub flange. 9. Hold the hub flange and twist the hub clockwise until the paper core is tight. 10. P osition the slot in the hub t o the top . 11. Align the leading edge of the first label on t he inside str ip with the slot in the hub and tape t he supply to the core (Figure 14).
12. Slide the separator disk and t he ne xt core ont o the hub (Figure 15). 13. Hold the core against the separator disk, inser t t he core lock (met al strip) into the slot, and slide it into the c or e . 14. Align the leading edge of the first label on t he middle s t rip with the slot in the hub and tape t he supply to the core.
15. Hold the second separator disk with the inside not ch up (in line with the core loc k) and slide it onto the hub (Figure 16). 16. Place the third core over the core lock and slide it onto the hub . Second Separator Disk Third Core Core Loc k Notc h in Disk Figur e 16 5.
17. Slide the third core against the second separ ator disk (Figure 17). 18. Align the leading edge of the first label on t he outside s t rip with the slot in the hub and tape t he supply to the core.
19. Hold the flanged collar assemb ly wit h the opening in the collar up . Then install it on the hub as shown in Figure 18. Opening in Collar Figur e 18 5.
20. Rechec k the print er to re wind alignment and fine adjust as necessary . 21. V erify that the separator bars are loc at ed between th e strip as shown in Figure 19.
Supply Remo va l 1. Remov e the core lock (metal str ip). 2. Remov e the flanged collar assembly . 3. Remov e the outside core and r oll of labels. 4. Remov e the second separator disk. 5. Remov e the middle core and r o ll of labels . 6. Remov e the inside separator disk.
Monarc h 415 Rewind Operato r ’ s Ha ndbook 20.
6. Sp ecifica tions a nd Supp lies Specifications Height: Width: Depth: 13.75 inches (349.25 mm) 12.50 inches (317.5 mm) 11.5 inches (292.10 mm) Weight: 18 lbs. (8.14 kg) Shipping Weight: 20 lbs. (9.05 kg) Powe r: 115 VAC 60 HZ 30 Watts .3 Amps 220/240 50/60 HZ 30 Watts .
7. Troubl eshooti ng Problem Corrective Action Power switch light does not light. Connect the power cord. Call Monarch Service. Dancer arm does not activate the rewind.
Append ix A: Rewind Alignme nt Locati on Guid e 1135 80 Locati on Guid e 1135 76 Locat ion Guide not availa ble Locati on Guid e 1135 76 Locat ion Gu ide 1135 76 Locat ion Gu ide 1135 76 Locati on Gui.
F or supplies, service, or assis t ance c all: TOLL FREE: 1-800- 543-66 50 (In the U.S. A.) 1-800- 263-4650 (In Canada) www.paxa r.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Paxar Monarch 415 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Paxar Monarch 415 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Paxar Monarch 415 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Paxar Monarch 415 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Paxar Monarch 415, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Paxar Monarch 415.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Paxar Monarch 415. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Paxar Monarch 415 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
