Manuale d’uso / di manutenzione del prodotto Hotwire 7984 del fabbricante Paradyne
Vai alla pagina of 122
HOTWIRE 7984 M/HDSL ST ANDALONE TERMINA TION UNIT WITH DSX-1 INTERF ACE USER’S GUIDE Document No. 7984-A2-GB20-10 February 1999.
Printed on recycled paper A 7984-A2-GB20-10 February 1999 Copyright E 1999 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law .
Important Information B 7984-A2-GB20-10 February 1999 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual.
Important Information C 7984-A2-GB20-10 February 1999 EMI W arnings ! W ARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
i 7984-A2-GB20-10 February 1999 Contents About This Guide H Document Purpose and Intended Audience v . . . . . . . . . . . . . . . . . . . . . . . . . H Document Summary v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents ii 7984-A2-GB20-10 February 1999 3 Initial Startup and Configuration H Overview 3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Connecting Power to the Unit 3-2 . . . . . . . .
Contents iii 7984-A2-GB20-10 February 1999 5 T esting H Accessing the T est Menu 5-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Running Network T ests 5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents iv 7984-A2-GB20-10 February 1999 A Configuration Option T ables H Overview A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Network Interface Options Menu A-2 . . . . . . . . . .
v 7984-A2-GB20-10 February 1999 About This Guide Document Purpose and Intended Audience This guide contains information needed to set up, configure, and operate the Hotwire 7984 Multirate High-bit-rate Digital Subscriber Line (M/HDSL) Standalone T ermination Unit with DSX-1 interface, and is intended for installers and operators.
About This Guide vi 7984-A2-GB20-10 February 1999 Section Description Appendix A Configuration Option T ables. Contains all configuration options, default settings, and possible settings. Appendix B Standards Compliance for SNMP T raps. Contains SNMP trap compliance information.
1-1 7984-A2-GB20-10 February 1999 About the Hotwir e 7984 Standalone T ermination Unit 1 M/HDSL Overview Hotwire t Multirate High-bit-rate Digital Subscriber Line (M/HDSL) products maximize customer service areas by varying the DSL line rate.
About the Hotwire 7984 Standalone T ermination Unit 1-2 7984-A2-GB20-10 February 1999 H Local Management (standalone unit). Provides local management using a: — T erminal or equivalent through the COM port of the unit — T elnet through the COM port of the unit — NMS connection through the 10BaseT port H Remote Management (DSLAM card).
About the Hotwire 7984 Standalone T ermination Unit 1-3 7984-A2-GB20-10 February 1999 Network Configuration Figure 1-1 shows several configurations including a network application using a 2-port Hotwire 8784 M/HDSL T ermination Unit in a central office (CO).
About the Hotwire 7984 Standalone T ermination Unit 1-4 7984-A2-GB20-10 February 1999 Fr ont Panel LED Status Indicators Figure 1-2 shows the front panel of the 7984 Standalone T ermination Unit. For more information on front panel LEDs, refer to Chapter 4, Monitoring the Unit .
About the Hotwire 7984 Standalone T ermination Unit 1-5 7984-A2-GB20-10 February 1999 SNMP Management Capabilities The termination unit supports SNMP V ersion 1, and can be managed by any industry-standard SNMP manager and accessed using SNMP by external SNMP managers.
About the Hotwire 7984 Standalone T ermination Unit 1-6 7984-A2-GB20-10 February 1999 This page intentionally left blank..
2-1 7984-A2-GB20-10 February 1999 Using the Asynchr onous T erminal Interface 2 User Interface Access Y ou can communicate with the Hotwire 7984 Standalone T ermination Unit with an asynchronous termi.
Using the Asynchronous T erminal Interface 2-2 7984-A2-GB20-10 February 1999 Initiating an A TI Session The Main Menu screen is displayed on the screen unless a login ID and password is required or the A TI is already in use.
Using the Asynchronous T erminal Interface 2-3 7984-A2-GB20-10 February 1999 main Access Level: Administrator Hotwire Model 7984 MAIN MENU Status Test Configuration Control –––––––––.
Using the Asynchronous T erminal Interface 2-4 7984-A2-GB20-10 February 1999 The following illustration shows the menu paths to the different A TI screens.
Using the Asynchronous T erminal Interface 2-5 7984-A2-GB20-10 February 1999 Scr een W ork Areas There are two user work areas: H Screen area – This is the area above the dotted line that provides the menu path, menus, and input fields. The menu path appears as the first line on the screen.
Using the Asynchronous T erminal Interface 2-6 7984-A2-GB20-10 February 1999 Navigating the Scr eens Y ou can navigate the screens by: H Using keyboard keys H Using screen function keys H Switching between the two screen work areas Keyboard Keys Use the following keyboard keys to navigate within the screen.
Using the Asynchronous T erminal Interface 2-7 7984-A2-GB20-10 February 1999 The current setting or value appears to the right of the field name. Y ou can enter information into a selected field by: H T yping in the first letter(s) of a field value or command.
Using the Asynchronous T erminal Interface 2-8 7984-A2-GB20-10 February 1999 Switching Between Screen W ork Areas Select Ctrl-a to switch between the two screen work areas to perform all screen functions. " Procedur e T o access the screen function area below the dotted line: 1.
Using the Asynchronous T erminal Interface 2-9 7984-A2-GB20-10 February 1999 Ending an A TI Session Use the E xit function key from any screen to terminate the session. " Procedur e T o end a session with the asynchronous terminal interface: 1. Press Ctrl-a to go to the screen function key area below the dotted line.
Using the Asynchronous T erminal Interface 2-10 7984-A2-GB20-10 February 1999 This page intentionally left blank..
3-1 7984-A2-GB20-10 February 1999 Initial Startup and Configuration 3 Overview This chapter provides instructions on how to access and configure your unit for the first time. This chapter includes procedures for: H Connecting power to the unit. H Connecting the unit to the network.
Initial Startup and Configuration 3-2 7984-A2-GB20-10 February 1999 Connecting Power to the Unit If your package includes a power pack: Plug the power pack into an ac outlet having a nominal voltage rating between 100–240 V ac. Connect the output cable of the power pack to the connector marked POWER on the rear panel.
Initial Startup and Configuration 3-3 7984-A2-GB20-10 February 1999 Connecting to the Network " Procedur e T o connect your unit to the network: 1. Connect one end of the network cable into the rear panel DSL jack. 2. Connect the other end to your DSL network interface.
Initial Startup and Configuration 3-4 7984-A2-GB20-10 February 1999 Entering Identity Information After accessing your unit for the first time, use the Change Identity screen to determine SNMP administrative system information that will be displayed on the Identity screen of the Status branch.
Initial Startup and Configuration 3-5 7984-A2-GB20-10 February 1999 " Procedur e T o enter Change Identity screen information: 1. Position the cursor in the System Name field. Enter a name unique in your network to identify the SNMP managed node (or unit).
Initial Startup and Configuration 3-6 7984-A2-GB20-10 February 1999 Choosing a Configuration Mode Y ou can make configuration changes either through a VT100-compatible terminal and the unit’s Configuration menus, or by manually changing switches on the board.
Initial Startup and Configuration 3-7 7984-A2-GB20-10 February 1999 Configuring the Unit Using the Internal Switches Use internal Switchpacks S1 and S2 to manually configure the unit.
Initial Startup and Configuration 3-8 7984-A2-GB20-10 February 1999 Switchpack Locations Use Figure 3-1 to locate Switchpacks S1 and S2. 98-16073a Switchpac k S1 & S2 F ront S2 Rear S1 678 ON 12345 678 ON 12345 Figure 3-1.
Initial Startup and Configuration 3-9 7984-A2-GB20-10 February 1999 Switchpack Definitions Manually change configuration options by moving Switchpack S1 DIP switches on the card. T able 3-1 lists Switchpack S1 definitions. T able 3-1. Switchpack S1 Definitions Switch # .
Initial Startup and Configuration 3-10 7984-A2-GB20-10 February 1999 T able 3-2 lists Switchpack S2 definitions. T able 3-2. Switchpack S2 Definitions Switch # .
Initial Startup and Configuration 3-1 1 7984-A2-GB20-10 February 1999 Accessing and Displaying Configuration Options T o display configuration options, you must first load a configuration into the edit area.
Initial Startup and Configuration 3-12 7984-A2-GB20-10 February 1999 Configuration Edit/Display The Configuration Edit/Display screen is displayed when the current, customer , or default configuration is loaded.
Initial Startup and Configuration 3-13 7984-A2-GB20-10 February 1999 Configuration Loader The Configuration Loader screen allows you to upload configurations to and download configurations from a TFTP server .
Initial Startup and Configuration 3-14 7984-A2-GB20-10 February 1999 2. Position the cursor in the TFTP Server IP Address field. Enter the TFTP server IP address. 3. Position the cursor in the Destination field. Use the spacebar to select a network destination for the TFTP server .
Initial Startup and Configuration 3-15 7984-A2-GB20-10 February 1999 Saving Configuration Options When changes are made to the configuration options through the Configuration Edit/Display branch, the changes must be saved to take effect. Use the S ave key or Save Configuration screen.
Initial Startup and Configuration 3-16 7984-A2-GB20-10 February 1999 Download Code The Download Code screen allows you to download firmware from a TFTP server .
4-1 7984-A2-GB20-10 February 1999 Monitoring the Unit 4 What to Monitor This chapter presents information on how to access and monitor Hotwire 7984 Standalone T ermination Units on the T1 network.
Monitoring the Unit 4-2 7984-A2-GB20-10 February 1999 V iewing System and T est Status T o view System and T est Status information, follow this menu selection sequence: Main Menu → Status → Syste.
Monitoring the Unit 4-3 7984-A2-GB20-10 February 1999 Health and Status The following messages can appear in the first column of the System and T est Status screen. The highest priority Health and Status message also appears on all A TI screens on the bottom right.
Monitoring the Unit 4-4 7984-A2-GB20-10 February 1999 T able 4-1. Health and Status Messages (2 of 2) Message What T o Do What Message Indicates Net Margin Threshold, Pt 1 The signal-to-noise margin has exceeded the configured threshold. 1. Reconfigure the unit to a higher Net Margin Threshold.
Monitoring the Unit 4-5 7984-A2-GB20-10 February 1999 Self-T est Results The results of the last power-up or reset self-test appear in the middle column of the System and T est Status screen. T able 4-2. Self-T est Results Messages Message What Message Indicates What T o Do CPU Failed The CPU failed internal testing.
Monitoring the Unit 4-6 7984-A2-GB20-10 February 1999 T est Status The T est Status messages in the following table appear in the right column of the System and T est Status screen. T able 4-3. T est Status Messages T est Status Message Meaning No T est Active No tests are currently running.
Monitoring the Unit 4-7 7984-A2-GB20-10 February 1999 V iewing Network Err or Statistics The 7984 Standalone T ermination Unit maintains error statistics on the network DSL interface for Port 1. Statistics are maintained for up to 96 15-minute intervals (24 hours).
Monitoring the Unit 4-8 7984-A2-GB20-10 February 1999 Use the virtual function keys to page through the intervals and clear statistics. This Field . . . Contains . . . Current Interval T imer The number of seconds which have elapsed in the current 15-minute interval.
Monitoring the Unit 4-9 7984-A2-GB20-10 February 1999 This Field . . . Contains . . . Current Interval T imer The number of seconds which have elapsed in the current 15-minute interval. Maximum value is 900 seconds (15 minutes). This counter resets every 15 minutes.
Monitoring the Unit 4-10 7984-A2-GB20-10 February 1999 V iewing DSX-1 Performance Statistics DSX-1 performance statistics allow you to monitor the current status of the DSX-1 interface operations when ESF framing is selected.
Monitoring the Unit 4-1 1 7984-A2-GB20-10 February 1999 H Status: Contains the contents of the status events register . The status events register maintains a history of specific events that have occurred during an interval.
Monitoring the Unit 4-12 7984-A2-GB20-10 February 1999 V iewing 7984 Standalone T ermination Unit LEDs The 7984 Standalone T ermination Unit LEDs can be viewed on the Display LEDs status screen. This A TI status screen is available locally and remotely .
Monitoring the Unit 4-13 7984-A2-GB20-10 February 1999 7984 Standalone T ermination Unit LEDs The following table contains a description of the LEDs on the 7984 Standalone T ermination Unit front panel. POWER ALARM TEST DSL DSX-1 98-16116a 7984 M/HDSL TM TM T ype LED LED is .
Monitoring the Unit 4-14 7984-A2-GB20-10 February 1999 This page intentionally left blank..
5-1 7984-A2-GB20-10 February 1999 T esting 5 Accessing the T est Menu From the T est menu, you can run network tests, data port tests, and a front panel lamp test.
T esting 5-2 7984-A2-GB20-10 February 1999 Running Network T ests Network tests require the participation of your network service provider . T o access the Network T ests screen, follow this menu sele.
T esting 5-3 7984-A2-GB20-10 February 1999 Line Loopback Line Loopback (LLB) loops the received signal on the network interface back to the network without change. CAP DSL Po r t DSX-1 Po r t CAP T1 LIU F ramer F ramer T ransceiver AIS 98-16112 " Procedur e T o run a Line Loopback: 1.
T esting 5-4 7984-A2-GB20-10 February 1999 Repeater Loopback Repeater Loopback (RLB) loops the signal being sent from the data port back to the data port.
T esting 5-5 7984-A2-GB20-10 February 1999 DTE Loopback DTE Loopback loops the DSX signal back to itself before the signal is sent to the Framer . CAP DSL Po r t DSX-1 Po r t CAP T1 LIU F ramer F ramer T ransceiver 98-16110 All Ones " Procedur e T o run a DTE Loopback: 1.
T esting 5-6 7984-A2-GB20-10 February 1999 Send Remote Line Loopback The local unit initiates this test by sending a line loopback up or down command to the remote unit for 10 seconds. When the remote unit detects the loopback up command, it puts itself in line loopback and lights the front panel test LED.
T esting 5-7 7984-A2-GB20-10 February 1999 Send and Monitor 51 1 The L TU initiates the test by sending a command to the remote unit to send a 51 1 test pattern. When the remote unit detects the command, it sends a 51 1 pattern and lights the front panel test LED.
T esting 5-8 7984-A2-GB20-10 February 1999 Device T ests The Device T ests branch is used to access the only card-level test, the Lamp T est. T o access the Device T ests screen, follow this menu sele.
T esting 5-9 7984-A2-GB20-10 February 1999 Ending an Active T est A test initiated by the user can be ended by the user . T ests can also be terminated automatically by enabling the T est T imeout option from the System Options Menu.
T esting 5-10 7984-A2-GB20-10 February 1999 T elco-Initiated Payload Loopback The Hotwire 7984 Standalone T ermination Unit supports payload loopback as specified in A T&T TR 54016 and ANSI T1.403. A T elco-initiated line loopback loops the received signal on the DSX-1 interface back to the DSX-1 interface.
6-1 7984-A2-GB20-10 February 1999 Messages and T r oubleshooting 6 Overview There are many resources available to assess the status of the device and contribute to problem resolutions.
Messages and T roubleshooting 6-2 7984-A2-GB20-10 February 1999 Configuring SNMP T raps An SNMP trap can be automatically sent out through the EOC or the Management port to an SNMP manager when the 7984 Standalone T ermination Unit detects conditions set by the user .
Messages and T roubleshooting 6-3 7984-A2-GB20-10 February 1999 Device Messages The Device Messages in T able 6-1, listed in alphabetical order , can appear in the messages area at the bottom of the A TI screens. T able 6-1. Device Messages (1 of 2) Device Message What Message Indicates What T o Do Access level is Operator .
Messages and T roubleshooting 6-4 7984-A2-GB20-10 February 1999 T able 6-1. Device Messages (2 of 2) Device Message What T o Do What Message Indicates Limit of six Login IDs reached An attempt to enter a new login ID was made, and the limit of six login/password combinations has been reached.
Messages and T roubleshooting 6-5 7984-A2-GB20-10 February 1999 T r oubleshooting This 7984 Standalone T ermination Unit is designed to provide you with many years of trouble-free service. If a problem occurs, however , refer to T able 6-2 for possible solutions.
Messages and T roubleshooting 6-6 7984-A2-GB20-10 February 1999 T able 6-2. T roubleshooting (2 of 2) Symptom Solutions Possible Cause Not receiving data. H The network or data port cables are not connected (check front panel LEDs for more information).
7-1 7984-A2-GB20-10 February 1999 Security 7 Overview The 7984 Standalone T ermination Unit provides several methods of security by limiting user access to the A TI through option settings. Y ou can: H Enable the T elnet Login Required option. H Limit the access by setting a Session Access Level option of Operator for the T elnet Session.
Security 7-2 7984-A2-GB20-10 February 1999 Access level is also used to control access via T elnet. If the T elnet Session Access Level is set to Administrator (see T able A-5, T elnet Session Options ), a Login ID with an Operator access level is not permitted access.
Security 7-3 7984-A2-GB20-10 February 1999 3. Create the login by entering the following fields. Login IDs and passwords are case-sensitive. On the Login Entry screen, for the . . . Enter . . . Login ID 1 to 10 ASCII printable characters (hex21 through 7E).
Security 7-4 7984-A2-GB20-10 February 1999 Deleting a Login " Procedur e 1. T o delete a login record, follow this menu selection sequence: Main Menu → Control → Administer Logins 2. Select PgU p or PgD n and press Enter to page through login pages / records until you find the one to be deleted.
Security 7-5 7984-A2-GB20-10 February 1999 Limiting SNMP Access through the IP Addr esses of the Managers The unit provides an additional level of security through validation of the IP addresses.
Security 7-6 7984-A2-GB20-10 February 1999 If entering yes to prompt . . . Then . . . Reset COM Port usage H Port type is set to T erminal H Data Rate (kbps) is set to 9.
8-1 7984-A2-GB20-10 February 1999 IP Addr essing 8 Selecting an IP Addr essing Scheme The NTU’s network interface IP address is assigned through the peer IP address of the L TU’s Network Interface menu. The NTU obtains the L TU’s IP address when the PPP link is established over the EOC.
IP Addressing 8-2 7984-A2-GB20-10 February 1999 IP Addr essing Example 98-16107a DSLAM DSLAM 7984 MCC Backplane Address = 126.35.50.1 MCC Base Subnet Mask = 255.255.255.0 Po r t 1 P eer IP Address = 126.35.50.5 MCC LT U 8784 Po r t 2 P eer IP Address = 126.
A-1 7984-A2-GB20-10 February 1999 Configuration Option T ables A Overview The tables in this appendix summarize the configuration options accessed when you select the Configuration option on the Main Menu. The Configuration options are arranged into groups based upon functionality .
Configuration Option T ables A-2 7984-A2-GB20-10 February 1999 Network Interface Options Menu For Network Interface Options, refer to T able A-1. T o access the Network Interface Options screen, follo.
Configuration Option T ables A-3 7984-A2-GB20-10 February 1999 T able A-1. Network Interface Options (2 of 2) DSL Line Rate Possible Settings: 400, 528, 784, 1040, 1552 Default Setting: 1552 Determines the fixed line rate of the L TU, in kbps. H DSL Line Rate is only available when the unit is configured as an L TU, and AutoRate is set to Disable.
Configuration Option T ables A-4 7984-A2-GB20-10 February 1999 DSX-1 Interface Options For DSX-1 Interface Options, refer to T able A-2. T o access the DSX-1 Interface Options screen, follow this menu.
Configuration Option T ables A-5 7984-A2-GB20-10 February 1999 T able A-2. DSX-1 Interface Options (2 of 2) Line Coding Format Possible Settings: AMI, B8ZS Default Setting: B8ZS Specifies the line coding format to be used by the DSX interface. AMI – Indicates the line coding format used by the DSX interface is Alternate Mark Inversion (AMI).
Configuration Option T ables A-6 7984-A2-GB20-10 February 1999 System Options Menu For System Options, refer to T able A-3. T o access the System Options screen, follow this menu selection sequence: M.
Configuration Option T ables A-7 7984-A2-GB20-10 February 1999 T able A-3. System Options (2 of 2) T elco Initiated Loopback Possible Settings: Enable , Disable Default Setting: Enable Determines if the unit will respond to inband loopback commands on the DSX-1 interface.
Configuration Option T ables A-8 7984-A2-GB20-10 February 1999 Communication Port For Communication Port Options, refer to T able A-4. T o access the Communications Ports screen, follow this menu sele.
Configuration Option T ables A-9 7984-A2-GB20-10 February 1999 T able A-4. Communication Port Options (2 of 3) Data Rate Possible Settings: 9.6 , 14.4, 19.2, 28.8, 38.4 Default Setting: 9.6 Specifies the communication port baud rate. 9.6 – Communication port rate is 9600 bps.
Configuration Option T ables A-10 7984-A2-GB20-10 February 1999 T able A-4. Communication Port Options (3 of 3) Login Required (T erminal Use Only) Possible Settings: Enable, Disable Default Setting: Disable Specifies if an ID and password are required to access the asynchronous terminal interface on the communication port.
Configuration Option T ables A-1 1 7984-A2-GB20-10 February 1999 Management and Communication Options Menu The Management and Communication Options Menu includes the following: H T elnet Session Optio.
Configuration Option T ables A-12 7984-A2-GB20-10 February 1999 T able A-5. T elnet Session Options T elnet Session Possible Settings: Enable, Disable Default Setting: Enable Specifies if the T ermination Unit will respond to a T elnet session request from a T elnet client on an interconnected IP network.
Configuration Option T ables A-13 7984-A2-GB20-10 February 1999 Communication Protocol Options The communication protocol configuration options specify the information necessary to support the IP communication network, including IP address and link protocols.
Configuration Option T ables A-14 7984-A2-GB20-10 February 1999 T able A-6. Communication Protocol Options (1 of 2) Node IP Address Possible Settings: 000.000.000.000 – 223.255.255.255 Default Setting: 000.000.000.000 Specifies the Node IP address. H Node IP Address is only available when the standalone unit is configured as an L TU.
Configuration Option T ables A-15 7984-A2-GB20-10 February 1999 T able A-6. Communication Protocol Options (2 of 2) Communication Port Subnet Mask Possible Settings: 000.000.000.000 – 255.255.255.255 Default Setting: 000.000.000.000 Specifies the unit’s Communication Port Subnet Mask when the unit is configured as a network communication link.
Configuration Option T ables A-16 7984-A2-GB20-10 February 1999 General SNMP Management Options SNMP configuration options allow you to specify the information necessary to support the T ermination Unit General SNMP functionality .
Configuration Option T ables A-17 7984-A2-GB20-10 February 1999 T able A-7. General SNMP Management Options (2 of 2) Name 1 Access Possible Settings: Read, Read/Write Default Setting: Read Determines the access level for Community Name 1. Read – Allows read-only access (get) for Community Name 1.
Configuration Option T ables A-18 7984-A2-GB20-10 February 1999 SNMP NMS Security Options SNMP configuration options allow you to specify the information necessary to support the T ermination Unit SNMP NMS Security .
Configuration Option T ables A-19 7984-A2-GB20-10 February 1999 T able A-8. SNMP NMS Security Options (2 of 2) NMS n IP Address Possible Settings: 000.000.000.000 – 223.255.255.255, Clear Default Setting: 000.000.000.000 Specifies the Internet Protocol address used to identify each SNMP manager .
Configuration Option T ables A-20 7984-A2-GB20-10 February 1999 SNMP T raps Options SNMP configuration options allow you to specify the information necessary to support the 7984 termination unit SNMP traps.
Configuration Option T ables A-21 7984-A2-GB20-10 February 1999 T able A-9. SNMP T raps Options (2 of 3) NMS n IP Address Possible Settings: 000.000.000.000 – 223.255.255.255, Clear Default Setting: 000.000.000.000 Specifies the Internet Protocol address used to identify each SNMP trap manager .
Configuration Option T ables A-22 7984-A2-GB20-10 February 1999 T able A-9. SNMP T raps Options (3 of 3) Link T raps Possible Settings: Disable, Up, Down, Both Default Setting: Both Determines if SNMP traps are generated for link up and link down for one of the communication interfaces.
B-1 7984-A2-GB20-10 February 1999 Standards Compliance for SNMP T raps B SNMP T raps This section describes the unit’s compliance with SNMP standards and any special operational features for the SNMP traps supported.
Standards Compliance for SNMP T raps B-2 7984-A2-GB20-10 February 1999 linkUp and linkDown The link SNMP traps are: H linkUp – The unit recognizes that one of the communication interfaces is operational. H linkDown – The unit recognizes that one of the communication interfaces is not operational.
Standards Compliance for SNMP T raps B-3 7984-A2-GB20-10 February 1999 Enterprise-Specific T raps EnterpriseSpecific traps indicates that an enterprise-specific event has occurred.
Standards Compliance for SNMP T raps B-4 7984-A2-GB20-10 February 1999 The tests that affect the enterpriseT estStart, enterpriseT estStop, and the variable-bindings are different for each particular interface. Diagnostic tests are only supported on the physical T1 network and user data port interfaces.
C-1 7984-A2-GB20-10 February 1999 Cables and Pin Assignments C Overview The following sections provide pin assignments: H T1 Network Interface Cable H DSL Network Interface Cable H COM Port Interface .
Cables and Pin Assignments C-2 7984-A2-GB20-10 February 1999 T1 Network Interface The T1 network interface is an RJ48C, 8-position, unkeyed modular connector for a 100-ohm balanced interface (T able C-1, Figure C-1).
Cables and Pin Assignments C-3 7984-A2-GB20-10 February 1999 DSL Network Interface Cable The DSL line interface cable is a 20-foot, 24 A WG solid, 2-twisted-pair cable that is RJ48C-to-RJ48C (T able C-2, Figure C-2).
Cables and Pin Assignments C-4 7984-A2-GB20-10 February 1999 COM Port Interface Cable The COM port connects to either a PC or to an ASCII terminal or printer for alarms. The COM port-to-PC cable is a 14-foot, 26 A WG, 8-conductor cable with an 8-position modular plug keyed connector and a DB9 socket connector (Figure C-3).
Cables and Pin Assignments C-5 7984-A2-GB20-10 February 1999 T able C-3. COM Port Connector (J6) Signal Direction Pin Number Reserved for future use to DTE (Out) 1 DCE Received Data to DTE (Out) 2 Sig.
Cables and Pin Assignments C-6 7984-A2-GB20-10 February 1999 Power Input Connector The required input power connector leads are shown in T able C-4. T able C-4. DC Power Connector Signal Pin Number +24 Vdc 5 +24 Vdc Return 4 Chassis Ground 3 Optional Power Cable The optional power cable is a 14.
D-1 7984-A2-GB20-10 February 1999 T echnical Specifications D Specifications Criteria* Size Width 7.25 inches (18.4 cm) Height 1.5 inches (3.8 cm) Length 9.4 inch (24.9 cm) Weight Approximately 1.25 lbs. (0.6 kg) Approvals Safety Certifications Refer to the equipment’s label for approvals on product.
T echnical Specifications D-2 7984-A2-GB20-10 February 1999.
GL-1 7984-A2-GB20-10 February 1999 Glossary A random bit test 51 1 bytes in length. Alarm Indication Signal. A signal transmitted downstream instead of the normal signal to preserve transmission continuity and to indicate to the rest of the network that a fault exists.
Glossary GL-2 7984-A2-GB20-10 February 1999 Digital Subscriber Line Access Multiplexer . A platform for DSL modems that provides high-speed data transmission over traditional twisted-pair wiring. Data Set Ready . A signal from the modem to the DTE that indicates the modem is turned ON and connected to the DTE.
Glossary GL-3 7984-A2-GB20-10 February 1999 High-bit-rate Digital Subscriber Line. A technique for high bandwidth, bidirectional transmission over copper wire for T1 and E1 services. Internet Protocol. An open networking protocol used for internet packet delivery .
Glossary GL-4 7984-A2-GB20-10 February 1999 Severely Errored Seconds. Usually defined as a second during which a specific number of CRC errors was exceeded, or an OOF or other critical error occurred. Simple Network Management Protocol. Protocol for open networking management.
IN-1 7984-A2-GB20-10 February 1999 Index A Abort All T ests, 5-1 ac transformer , connecting, 3-2 access SNMP , 7-4 to asynchronous terminal interface, 2-3 access level effective, 7-1 functions availa.
Index IN-2 7984-A2-GB20-10 February 1999 D dc power option, 3-2 default configuration area, 3-6 delete, Login ID, 7-4 device, messages, 6-3– 6-4 dimensions, D-1 Disconnect T ime for T elnet session,.
Index IN-3 7984-A2-GB20-10 February 1999 M main menu, 2-2, A-1 Management and Communication Options, A-1 1 management port access, 7-1 settings, 2-1 manual configuration, switchpacks, 3-7 Margin Thres.
Index IN-4 7984-A2-GB20-10 February 1999 SNMP enable/disable management, A-16 limiting access, 7-4 NMS IP Address, A-19 NMS Security Options, A-18 support overview , 1-5 trap options, 6-2 trap support.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Paradyne Hotwire 7984 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Paradyne Hotwire 7984 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Paradyne Hotwire 7984 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Paradyne Hotwire 7984 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Paradyne Hotwire 7984, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Paradyne Hotwire 7984.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Paradyne Hotwire 7984. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Paradyne Hotwire 7984 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.