Manuale d’uso / di manutenzione del prodotto 950 st del fabbricante ParaBody
Vai alla pagina of 26
Serious Steel 950 ST ASSEMBLY INSTRUCTIONS Pa.rt # 6639601 R~vision: 10/10/96.
***IMPORTANT*** ¯ THE pARABODY 950 ST MUST BE ASSEMBLED ON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. PARABODY INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED B~( TWO PERSONS TO AVOID" POSSIBLE INJURY. ¯ KEEP ALL FRAME CONNECTIONS LOOSE, UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN.
TTENTION . !! IliA ~ (1) B O L I; TWO (2) ~ WASHERS. AN_D__ONE -- LOCKNUT NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. ,1,3///ii!!1 BOLT LENGTH BOLT LENGTH RULER: 1 2 3 4 .
950 ST Pacts List KEY} PART# DFSCRIPTION II 6623603 PRESS WT STACK BASEWHT 2 I 6624202 BACK’ PAl) ANGLE LEFTBLK 3..I 662’4302 BACK PADANGLFRIGHTBLK 4 I 6622903 PECARM RIGHTWHT 5 I 6623003 PECARM LEFTWHT 6 t 6’623503 PRESS AR/Vl WHT " ~ I 6624502 CALF/LOW RQW 8LK 8 I 662460,3 LEG CURL/EXTWHT " ~ } 6625203 LEG CURL HANDLEWHT .
Frame Assembly Instructions Use t’his procedure to ossemble the frame of the PareBody 950ST Step 1 A. Loosely assemble the leg wei.~,ht stack bose (18) a.n,,d the press weight s~ack base (1) to the (15) using two 1/2 x .3-1/2 bolts (91), four 1/2 washers (79), and two 1/2" nylock nuts (B2) ~ho~n.
Step 2 A. Securely assemble the floating pulley stop (:52), and the s.eat support (33) to the front upright using two 1/2 x 4.-1/2" bolts (90), four 1/2’ washers (.79), and two 1/2" nylock nuts (B2). B. Apply eight 1-1/2 x 3/4" glides (63) to the inside surface of the seat support (32;) as shown.
Step 3 A. Securely assemble the bearing housl.n,g (22) and the center, pulley bracket (36) to fine front upright (31) using two 1/2 x 4-1/2’ bolts (90), four 1/2’ washers (79), and two 1/2" nylock (82). (Note: Push bearing housing up as high as possible before tightening.
Siep 4 /2" A. Securely attach fh~, press base (13) fo the base (15) using two 1/2 x 3-1/4" bolts (89), washers (79) ,~nd two 1/.2".nylock nuts .(8,2), and fo the rear upright (21) using one 3/8 x 3" (95), two 3/8’ washers (,78) and one 3/8’ nylock B.
Step 5 , nLJt (1~2), and two 3/8" I 3’ bolts (95), two 1/2’ washers , 2’1 nylock nufs (831. (Note: Make.
Slap 8 A. Slide two hinge tabs (73) onto the wolff sleeve (39) and securely attach press seat pad (49) The "hinge" part of the hinge tab 1" two 3/B x bolts (97), and two 3/B" washers (7B).
Step 7 A. Loosely aftach the press arm odiu.s,, ~ (23) to the rear up.r,!gh~ (21) using two 1" pillow block bearings (112), four 3/8 x 3-1/4 bolts (98), four 3/B’ washers (78), and B. Center press arm adiust (23) to I~ne up w~th ~he post on the press base (13) and securely ~ighlen set screws on the pillow block bearings (112).
Step B A. Securely attoch the rear leg base (10) ond the leg curl hondle (9) *o the leg frame (14) using 1/2 × 3-1/4" bolts (Bg), t~.o .~/8 × 3-1/4". bolts (98), tour 1/2" washers (79), ~o,~r ~/B" washers (TB), *wo 1/2" nylock nuts (,B2), and two 3/B" nylock nuts (,B3).
STEP 9-B STEP 9 A. Slide fwlo,, hinge tabs (73) onto the leg frame (14) and securely ah~ach leg seat pad (47) using 3/8 x bolts (97), and two 3/B" washers (78).
STEP 1 1 A. gEE ])ETA, IL Securely assemble two 3/8" spring pins (62) to the leg curl/extension (8) as shown. B. Apply eight 1-1/2 x 3/4" glides (63) to the outside surfaces of each roller .pad adiuster (34) shown, and insert roller pad adjusters (34) into the leg curl/extension (B).
SEE NOTE Step 1 2 A. Insert two plate bushings (102) into the "ParaBody" side of each of sixty weight plates (67) shown. B. Insert one guide rod (28) through one weight stack cushion (109) and into each ef the large holes in the base (15), the leg weight stack base (18), and the press weight stack press (1) as C.
Step 1 3 A. Slide peo guide rod support ~4~,), onto ~he eo we]aht slack guide rods and loosely :ff~ach it fo the boom using tiwo 3/B bolts.(95), four 3/8" washers (781, and two 3/8 nylock nuts (831¯ (Note: This connection will be secured in a la’ter step offer ~he pulleys are assembled.
CABLE GUIDE ’ PEC DEC% " CABLE STAMPED PART NUMBER 65356 // 77 5/8" STAMPED 66274- // PART NUMBER AB CRUNCH~ I. ,] STAMPED PART NUMBER 66275 ’ // 61 3/4" LEG PRES S~Xx CABLE STAMPED.
Pec Dec Cable Assembly Instructions Use this procedure to assemble ~he pec dec cables of the Pc~raBody 950ST Step C Step F & H LAT CABLE Stel3 1 order, route the threaded end of the lot coble (~403~! through the top boom (20), the boise A. ~r~5~h, iSen d the Icrge hole in the pec guide rod support B.
Step 2 A. Conneot one end of the pec deo cable (104) to the slotted bushing on the right peo oam (29). Route the other end of the pec dec cable around the front upright (31) and connect to the slotted bushing on the left pec cam (29).
Step 3 A. Securely assemble l,~he ’U’ bracket (~26) fo the threaded end of the ab crunch c~ble (106) using two 1/4" washers ~80) and two 1/4" nylock nuts (B1). (Note: Position the ’U’ br’ackef in ~he middle of the thread as shown and "lock’-nuts together.
Step 4 A. Securely assemble tl~e ball end of the ab crunch cable (106) a,,nd one 3-1/2" pu. lle’/ (111) f.o,,fhe front upright (.51) using two 5/8 x 2-3/4" bolts (99), two .~/8 flange spacers f,74), two washers (78), and two 3/8" nylock nuts (83).
Step I A. Co Do Press Station Cable Assembly Instructions Use this procedure to assemble the press station cable of the ParaBody gSI)ST Secure ’~he ball end of the press cable (105) and two 3-1/2&qu.
S~ep 2 Secure the press cable (105) and two .~-1/2" pulleys (111) to the pulley flats on the press base (15) and press weight stack base (1) using two 3/8 x 2" bolts 78). and ’two .~/8" nylock nu,s(83). (Note: The press cable should be routed underneath the short leg of the ’L’ bracket.
STEP 1 A. Leg Sfatlon Cable Assembly Instructions Use this procedure to assemble the leg station cable of the PARABODY g50 ST Route the "loop" end of the leg cable (108) into the rear slot of the leg welght star< base (18) behind the weight stack, and out through the slot near the leg station.
STEP 2 A. Screw the threaded end of the leg cable (108) approximately 3/4" into the end of the selector shall (115) and figh’~en [am nut securely as shown.
Securely assemble the,~ press station shroud (53) the press guide rod .~upport (24) and the press weight stack base (1) using four 3/8 x 1" black button head cap screws (59).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il ParaBody 950 st è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del ParaBody 950 st - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso ParaBody 950 st imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul ParaBody 950 st ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il ParaBody 950 st, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del ParaBody 950 st.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il ParaBody 950 st. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo ParaBody 950 st insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
