Manuale d’uso / di manutenzione del prodotto PT-DZ10KU del fabbricante Panasonic
Vai alla pagina of 187
Thank you for purchasing this Panasonic product. ■ Before operating this product, please read the instructions carefully and save this manual for future use. ■ Before using your projector , be sure to read “Read this rst!” ( x pages 2 to 9).
2 - ENGLISH Read this rst! Read this rst! W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning ash with arrowhead symbol, withi.
ENGLISH - 3 Read this rst! FCC NOTICE (USA) V erication Model Number: PT -DZ13KU/PT -DS12KU/PT -DW1 1KU/PT -DZ10KU T rade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: One Panasonic W ay , Secaucus, NJ 07094 T elephone number: (877)803-8492 E-mail: projectorsupport@us.
4 - ENGLISH Read this rst! W ARNING: r PO WER The wall outlet or the circuit breaker shall be installed near the equi pment and shall be easily accessible when problems occur . If the following problems occur , cut off the power supply immediately .
ENGLISH - 5 Read this rst! W ARNING: Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them. Doing so will cause the projector to overheat, which can cause re or damage to the projector . f Do not place the projector in narrow , badly ventilated places.
6 - ENGLISH Read this rst! W ARNING: r ACCESSORI ES Do not use or handle the batteries improperly , and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re. f Use AA/R6 batteries. f Do not use unspecied batteries.
ENGLISH - 7 Read this rst! CAUTION: r PO WER When disconnecting the power cord, be sure to hold the power plug and power connector . If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks will result.
8 - ENGLISH Read this rst! CAUTION: r MA INTENA NCE Do not attach the air lter unit while it is wet. Doing so may result in electric shock or malfunctions. f After you clean the air lter units, dry them thoroughly before reattaching them. Do not touch the fan with your ngers or any other parts of your body when replacing the lamp unit.
ENGLISH - 9 Read this rst! Brazil Only Brasil Apenas r Manuseio de b at eria s usada s BRASIL Após o uso, as pilhas e/ou baterias deverão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada.
10 - ENGLISH r T rademarks f Windows ® , Windows Vista ® , and Internet Explorer ® are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. f Mac, Mac OS, OS X, and Safari are trademarks of Apple Inc.
ENGLISH - 1 1 Features of the Projector High luminance and high color reproduction ▶ High luminance and high color reproduction are achieved with a small size by means of a unique optical system and lamp drive system.
12 - ENGLISH Contents Contents Read this rst! 2 Chapter 1 Preparation Precautions for use 16 Cautions when transporting 1 6 Cautions when installing 1 6 Security 1 8 Disposal 1 8 Cautions on use 1 .
ENGLISH - 13 Contents [ADV ANCED MENU] menu 85 [DIGIT AL CINEMA REALITY] 8 5 [BLANKING] 8 5 [INPUT RESOLUTION] 8 6 [CLAMP POSITION] 8 6 [EDGE BLENDING] 8 7 [FRAME RESPONSE] 8 8 [FRAME LOCK] 8 9 [RASTE.
14 - ENGLISH Contents Chapter 5 Maintenance Lamp/temperature/lter indicators 155 When an indicator lights up 155 Maintenance/replacement 157 Before performing maintenance/replacement 157 Maintenanc.
ENGLISH - 15 Chapter 1 Preparation This chapter describes things you need to know or check before using the projector ..
Chapter 1 Preparation — Precautions for use 16 - ENGLISH Precautions for use Cautions when transporting f The projection lens (optional) is susceptible to effects due to vibration or impact.
Chapter 1 Preparation — Precautions for use ENGLISH - 17 r Do not use the projector tilted to the right or left. Using the projector at a vertical angle that exceeds 15° may reduce product life or result in malfunction. r When installing and using the projector at an angle that exceeds 30° vertically , set [COOLING CONDITION] ( x page 109).
Chapter 1 Preparation — Precautions for use 18 - ENGLISH f Prevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and exhaust) of the projector .
Chapter 1 Preparation — Precautions for use ENGLISH - 19 f Directing a high-power laser beam onto the lens surface can damage the DLP chips. r Do not move the projector or subject it to vibration or impact while it is operating. Doing so may shorten the life of the built-in motor .
Chapter 1 Preparation — Precautions for use 20 - ENGLISH Accessories Make sure that the following accessories are provided with your projector . Numbers enclosed in < > show the number of accessories.
Chapter 1 Preparation — Precautions for use ENGLISH - 21 Optional accessories Optional accessories (product name) Model No. Projection lens Zoom lens ET -D75LE6, ET -D75LE8, ET -D75LE10, ET -D75.
Chapter 1 Preparation — Start-up display 22 - ENGLISH Start-up display When the projector is switched on for the rst time after purchase as well as when [ALL USER DA T A] in the [PROJECTOR SE.
Chapter 1 Preparation — Start-up display ENGLISH - 23 Initial setting (installation setting) Set [PROJECTION METHOD] and [COOLING CONDITION] depending on the installation mode.
Chapter 1 Preparation — About your projector 24 - ENGLISH About your projector Remote control 1 3 2 4 5 7 6 8 9 10 11 12 19 13 14 15 16 17 18 20 21 Front Side To p Bottom 1 Remote control indicator Flashes if any button in the remote control is pressed.
Chapter 1 Preparation — About your projector ENGLISH - 25 Note f The remote control can be used within a distance of about 30 m (98'5") if pointed directly at the remote control signal receiver .
Chapter 1 Preparation — About your projector 26 - ENGLISH 13 Security slot This security slot is compatible with the Kensington security cables. 14 Air intake port 15 <AC IN> terminal Connect the supplied power cord. 16 <MAIN POWER> switch T urns on/off the main power .
Chapter 1 Preparation — About your projector ENGLISH - 27 r Connecting terminals 1 2 3 4 7 8 9 10 11 12 13 5 6 6 1 <REMOTE 1 IN> terminal/<REMOTE 1 OUT> terminal These are the terminals to connect the remote control for serial control when the system uses multiple projectors.
Chapter 1 Preparation — Using the remote control 28 - ENGLISH Using the remote control Inserting and removing the batteries (i) (ii) Fig. 1 Fig. 2 1) Open the cover . (Fig. 1) 2) Insert the batteries and close the cover (insert the m side first).
Chapter 1 Preparation — Using the remote control ENGLISH - 29 Connecting to the projector with a cable When you use the system with multiple projectors, use commercial M3 stereo mini jack cables and connect the other devices to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projector body .
30 - ENGLISH Chapter 2 Getting Started This chapter describes things you need to do before using the projector such as the setup and connections..
Chapter 2 Getting Started — Setting up ENGLISH - 31 Setting up Installation mode There are six ways to set up the projector . Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD] ( x page 108) depending on the installation location. Set [COOLING CONDITION] ( x page 109) to [AUTO].
Chapter 2 Getting Started — Setting up 32 - ENGLISH Parts for ceiling mount (optional) Y ou can install the projector on the ceiling using the optional Ceiling Mount Bracket for Projectors (Model No.: ET -PKD310H (for High Ceilings), ET -PKD310S (for Low Ceilings)).
Chapter 2 Getting Started — Setting up ENGLISH - 33 [GEOMETR Y] projection range (Only for PT -DZ13KU, PT-DS12KU, PT -DZ10KU) [VERTICAL KEYST ONE] (viewed from the side) [HORIZONT AL KEYSTONE] (.
Chapter 2 Getting Started — Setting up 34 - ENGLISH When using the optional Upgrade Kit (Model No.: ET -UK20) (Only for PT -DZ13KU, PT-DS12KU) Projection lens Model No.
Chapter 2 Getting Started — Setting up ENGLISH - 35 Projection distance of each projection lens A ±5 % error in listed projection distances may occur. In addition, when [GEOMETRY] and [KEYST ONE] are used, distance is corrected to become smaller than the specied screen size.
Chapter 2 Getting Started — Setting up 36 - ENGLISH r When the screen aspect is 16:9 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 1.4-1.8:1 1.8-2.8:1 2.8-4.
Chapter 2 Getting Started — Setting up ENGLISH - 37 r When the screen aspect is 4:3 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 1.6-2.2:1 2.2-3.3:1 3.3-5.
Chapter 2 Getting Started — Setting up 38 - ENGLISH For PT -DS12KU r When the screen aspect is 4:3 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 1.5-2.0:1 2.
Chapter 2 Getting Started — Setting up ENGLISH - 39 r When the screen aspect is 16:9 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 1.5-2.0:1 2.0-30:1 3.0-5.
Chapter 2 Getting Started — Setting up 40 - ENGLISH For PT -DW1 1KU r When the screen aspect is 16:9 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 1.5-2.0:1 2.
Chapter 2 Getting Started — Setting up ENGLISH - 41 r When the screen aspect is 4:3 (Unit: m) Lens type Zoom lens Projection lens Model No. ET -D75LE1 ET -D75LE2 ET-D75LE3 ET -D75LE4 ET -D75LE8 ET -D75LE6 Throw ratio *1 2.0-2.7:1 2.7-4.1:1 4.1-6.
Chapter 2 Getting Started — Setting up 42 - ENGLISH Formula to calculate projection distance per projection lens T o use a screen size not listed in this manual, check the screen size SD (m) and use the respective formula to calculate projection distance.
Chapter 2 Getting Started — Setting up ENGLISH - 43 Projection lens Model No. Throw ratio Aspect ratio Projection distance (L) formula ET -D75LE30 2.4 to 4.7:1 16:10 Min. (L W) L = 2.0647 x SD - 0.1 131 Max. (L T) L = 4.0041 x SD - 0.1765 2.4 to 4.
Chapter 2 Getting Started — Setting up 44 - ENGLISH Projection lens Model No. Throw ratio Aspect ratio Projection distance (L) formula ET -D75LE20 1.8 to 2.6:1 4:3 Min. (L W) L = 1.4618 x SD - 0.0832 Max. (L T) L = 2.1241 x SD - 0.1 162 16:9 Min.
Chapter 2 Getting Started — Setting up ENGLISH - 45 Projection lens Model No. Throw ratio Aspect ratio Projection distance (L) formula ET -D75LE20 1.8 to 2.7:1 16:9 Min. (L W) L = 1.6324 x SD - 0.0832 Max. (L T) L = 2.3720 x SD - 0.1 162 2.5 to 3.
Chapter 2 Getting Started — Attaching/removing the projection lens (optional) 46 - ENGLISH Attaching/removing the projection lens (optional) Move the projection lens to the home position before replacing or removing the projection lens. ( x page 57) Attention f Replace the projection lens after turning off the power of the projector .
Chapter 2 Getting Started — Attaching/removing the projection lens (optional) ENGLISH - 47 Attention f Store the removed projection lens where it will be free from vibration and impact.
Chapter 2 Getting Started — Connecting 48 - ENGLISH Connecting Before connecting f Before connecting, carefully read the operating instructions for the external device to be connected. f T urn off the power of all devices before connecting cables.
Chapter 2 Getting Started — Connecting ENGLISH - 49 <DVI-D IN> terminal pin assignments and signal names Outside view Pin No. Signal name Pin No. Signal name (17) (24) (16) (9) (1) (8) (1) T .M.D.S data 2 - (13) — (2) T .M.D.S data 2+ (14) +5 V (3) T .
Chapter 2 Getting Started — Connecting 50 - ENGLISH For <SDI IN 1>/<SDI IN 2> terminals (PT -DZ13KU, PT -DS12KU), <SDI IN> terminal (PT -DZ10KU) The connection example is for PT -DZ13KU, PT-DS12KU.
ENGLISH - 51 Chapter 3 Basic Operations This chapter describes basic operations to start with..
Chapter 3 Basic Operations — Switching on/off the projector 52 - ENGLISH Switching on/off the projector Connecting the power cord Make sure that the supplied power cord is securely xed to the projector body to prevent it from being removed easily .
Chapter 3 Basic Operations — Switching on/off the projector ENGLISH - 53 Note f While the power indicator <ON (G)/ST ANDBY (R)> is lit in orange, the fan is running to cool the projector .
Chapter 3 Basic Operations — Switching on/off the projector 54 - ENGLISH Making adjustments and selections It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted.
Chapter 3 Basic Operations — Switching on/off the projector ENGLISH - 55 Switching off the projector SDI 1/2 VIDEO ENTER MENU LENS SHUTTER RGB 1 RGB 2 AUTO SETUP DVI-D HDMI SDI 1/2 1) 2) 1) 4) 3) 2 ) 1) Press the power standby < v > button.
Chapter 3 Basic Operations — Projecting 56 - ENGLISH Projecting Check the projection lens attachment ( x page 46), external device connection ( x page 48), power cord connection ( x page 52), switch on the power ( x page 53) to start projecting.
Chapter 3 Basic Operations — Projecting ENGLISH - 57 Moving the lens to the home position T o move the lens to the home position, perform the following procedure. 1) While the [SHIFT] adjustment screen is displayed, press the <DEF AUL T> button.
Chapter 3 Basic Operations — Projecting 58 - ENGLISH Projection lens Model No. ET -D75LE1, ET-D75LE2, ET -D75LE3, ET -D75LE4, ET -D75LE8, ET-D75LE10, ET -D75LE20, ET -D75LE30, ET-D75LE40 ET -D75LE6 PT -DW1 1KU Projection screen width H Standard projection position 0.
Chapter 3 Basic Operations — Projecting ENGLISH - 59 r Front view diagram of the lens mounter (viewed from the screen side) (a) (b) (c) Lens mount bracket Fixing screws Note f Focus adjustment screws (a), (b), and (c) are adjusted with the lens attached.
Chapter 3 Basic Operations — Projecting 60 - ENGLISH 6) Press the <SHIFT> button on the remote control or the <LENS> button on the control panel to display the [SHIFT] adjustment menu, and reset the screen position of the projected image on the screen surface back to an optimal state.
Chapter 3 Basic Operations — Operating with the remote control ENGLISH - 61 Operating with the remote control Using the shutter function If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the image temporarily .
Chapter 3 Basic Operations — Operating with the remote control 62 - ENGLISH Switching the input signal The input for projection can be switched. button 1) Press the input selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>, <HDMI>, <SDI 1/2>) buttons.
Chapter 3 Basic Operations — Operating with the remote control ENGLISH - 63 f This operation can be also performed using the <AUTO SETUP> button on the control panel. Note f The clock phase may shift even if it has completed without any incident.
64 - ENGLISH Chapter 4 Settings This chapter describes the settings and adjustments you can make using the on-screen menu..
Chapter 4 Settings — Menu navigation ENGLISH - 65 Menu navigation The on-screen menu (Menu) is used to perform various settings and adjustments of the projector . Navigating through the menu Operating procedure button 1) Press the <MENU> button on the remote control or control panel.
Chapter 4 Settings — Menu navigation 66 - ENGLISH 4) Press as to select a sub-menu, and press qw or the <ENTER> button to change or adjust settings. f Some items will switch in order as follows each time you press qw . ABC f For some items, press qw to display an individual adjustment screen with a bar scale as shown below .
Chapter 4 Settings — Menu navigation ENGLISH - 67 Main menu item Page [PROJECTOR SETUP] 108 [P IN P] 125 [TEST P A TTERN] 127 [SIGNAL LIST] 128 [SECURITY] 131 [NETWORK] 135 *1 Only for PT -DZ13KU, PT-DS12KU, PT -DW1 1KU Sub-menu The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
Chapter 4 Settings — Menu navigation 68 - ENGLISH Sub-menu item Factory default Page [CLAMP POSITION] [24] *1 86 [EDGE BLENDING] [OFF] 87 [FRAME RESPONSE] [NORMAL] 88 [FRAME LOCK] *2 [OFF] 89 [RASTER POSITION] ― 89 *1 Depends on the signal input.
Chapter 4 Settings — Menu navigation ENGLISH - 69 [PROJECTOR SETUP] Sub-menu item Factory default Page [PROJECTOR ID] [ALL] 108 [PROJECTION METHOD] [FRONT/FLOOR] 108 [COOLING CONDITION] [AUTO] 1.
Chapter 4 Settings — Menu navigation 70 - ENGLISH [NETWORK] Sub-menu item Factory default Page [NETWORK SETUP] ― 135 [NETWORK CONTROL] ― 135 [NETWORK ST A TUS] ― 136 Note f Some items may not be adjusted or used for certain signal formats to be input to the projector .
Chapter 4 Settings — [PICTURE] menu ENGLISH - 71 [PICTURE] menu On the menu screen, select [PICTURE] from the main menu, and select an item from the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [PICTURE] menu 72 - ENGLISH 2) Press qw or the <ENTER> button. f The [CONTRAST] individual adjustment screen is displayed. 3) Press qw to adjust the level. Operation Adjustment Range of adjustment Press the w button. Brightens the screen and makes the color deeper .
Chapter 4 Settings — [PICTURE] menu ENGLISH - 73 2) Press qw or the <ENTER> button. f The [COLOR TEMPERA TURE] individual adjustment screen is displayed. 3) Press qw to switch the item. f The items will switch each time you press the button.
Chapter 4 Settings — [PICTURE] menu 74 - ENGLISH 4) Press the <ENTER> button. f The [CHANGE TO *****] screen is displayed. 5) Press as to select [USER1] or [USER2]. f The status of the color temperature changed is saved to the selected item.
Chapter 4 Settings — [PICTURE] menu ENGLISH - 75 [1.0] Set so that images become as you like. [2.0] - [2.8] can be set in increments of 0.1. [1.8] [2.0] - [2.8] (increments of 0.1) *1 When [PICTURE MODE] is set to [DYNAMIC], [USER], or [DICOM SIM.
Chapter 4 Settings — [PICTURE] menu 76 - ENGLISH Note f If you press w while the adjustment value is [+15], the value will become [0]. If you press q while the adjustment value is [0], the value will become [+15]. [NOISE REDUCTION] Y ou can reduce noises when the input image is degraded and noise is occurring in the image signal.
Chapter 4 Settings — [PICTURE] menu ENGLISH - 77 Item Adjustment [DYNAMIC GAMMA] (Adjustment of signal compensation) [OFF] No correction. [1] Slightly compensates the signal. [2] Moderately compensates the signal. [3] Strongly compensates the signal.
Chapter 4 Settings — [PICTURE] menu 78 - ENGLISH sRGB-compliant video sRGB is an international standard (IEC61966-2-1) for color reproduction dened by IEC (International Electrotechnical Commission). Set according to the following steps to reproduce more faithful, sRGB compliant colors.
Chapter 4 Settings — [POSITION] menu ENGLISH - 79 [POSITION] menu On the menu screen, select [POSITION] from the main menu, and select an item from the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [POSITION] menu 80 - ENGLISH [DEF AUL T] Displays images without changing the aspect ratio of the input signals. [VID AUTO] *1 The projector identies the video ID (VID) embedded in the video signals and displays the image by automatically switching the screen sizes between 4:3 and 16:9.
Chapter 4 Settings — [POSITION] menu ENGLISH - 81 When [ASPECT] is set to [DEF AUL T] 1) Press as to select [ZOOM]. 2) Press the <ENTER> button. f The [ZOOM] screen is displayed. 3) Press as to select [MODE]. 4) Press qw to switch the item.
Chapter 4 Settings — [POSITION] menu 82 - ENGLISH [PC-1] *1 Uses the computer to perform geometric adjustment. [PC-2] *1 [PC-3] *1 *1 Advanced skills are necessary to use a computer to control geometric adjustment. Consult your dealer . Up to three geometric adjustments performed using the computer can be saved.
Chapter 4 Settings — [POSITION] menu ENGLISH - 83 [CURVED] [VERTICAL BALANCE] [HORIZONT AL BALANCE] [MAINT AIN ASPECT RA TIO] Select [ON] to correct while keeping the aspect ratio. Setting [CORNER CORRECTION] 1) Press as to select [GEOMETR Y]. 2) Press qw to select [CORNER CORRECTION].
Chapter 4 Settings — [POSITION] menu 84 - ENGLISH [KEYSTONE] (Only for PT -DW1 1KU) Y ou can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted. 1) Press as to select [KEYSTONE]. 2) Press the <ENTER> button.
Chapter 4 Settings — [ADV ANCED MENU] menu ENGLISH - 85 [ADV ANCED MENU] menu On the menu screen, select [ADV ANCED MENU] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [ADV ANCED MENU] menu 86 - ENGLISH Blanking correction Item Operation Adjustment Range of adjustment T op of the screen [UPPER] Press the q button. The blanking zone moves upward. PT -DZ13KU, PT-DZ10KU: T op to bottom 0 - 599 PT -DS12KU: T op to bottom 0 - 524 PT -DW1 1KU: T op to bottom 0 - 383 Press the w button.
Chapter 4 Settings — [ADV ANCED MENU] menu ENGLISH - 87 [EDGE BLENDING] The edge blending function allows multiple projector images to be seamlessly overlapped by using the inclination of the brightness at the overlapped area. 1) Press as to select [EDGE BLENDING].
Chapter 4 Settings — [ADV ANCED MENU] menu 88 - ENGLISH 15) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH]. 16) Press qw to set the region (width) of the [BLACK BORDER WIDTH] adjustment. f When PT -DZ13KU, PT-DS12KU, or PT -DZ10KU is used, proceed to Step 17) .
Chapter 4 Settings — [ADV ANCED MENU] menu ENGLISH - 89 [FRAME LOCK] (Only for PT -DZ13KU, PT-DS12KU, PT -DZ10KU) Set this to view 3D display when the vertical scanning frequency of the signal is 25 Hz, 50 Hz, and 100 Hz. 1) Press as to select [FRAME LOCK].
Chapter 4 Settings — [DISPLA Y LANGUAGE] menu 90 - ENGLISH [DISPLA Y LANGUAGE] menu On the menu screen, select [DISPLA Y LANGUAGE] from the main menu, and display the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [3D SETTINGS] menu ENGLISH - 91 [3D SETTINGS] menu (Only for PT -DZ13KU, PT-DS12KU, PT -DW1 1KU) On the menu screen, select [3D SETTINGS] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [3D SETTINGS] menu 92 - ENGLISH [3D SYNC MODE] Items set in [3D SYNC1] Items set in [3D SYNC2] [10] Stereo synch output Frame synch output [1 1] 3D IR TRANSMITTER (+) output.
Chapter 4 Settings — [3D SETTINGS] menu ENGLISH - 93 Note f When set to [AUTO], [SIMUL T ANEOUS], [SIDE BY SIDE], [T OP AND BOTTOM], [LINE BY LINE], or [FRAME SEQUENTIAL], 3D images are not displayed in [3D SIMUL INPUT SETTING]. In [AUT O], however , this only occurs when 3D format can be recognized.
Chapter 4 Settings — [3D SETTINGS] menu 94 - ENGLISH [3D W A VEFORM MONIT OR] [OFF] Hides the 3D waveform monitor . [ON] Displays the 3D waveform monitor . Note f The [CLOCK PHASE] setting is enabled at simultaneous input of RGB1 and RGB2 to adjust the right eye image.
Chapter 4 Settings — [3D SETTINGS] menu ENGLISH - 95 [3D TEST P A TTERN] The 3D test pattern can be used to check operation and make adjustments even without a 3D signal. 1) Press as to select [3D TEST P A TTERN]. 2) Press qw to switch the item.
Chapter 4 Settings — [DISPLA Y OPTION] menu 96 - ENGLISH [DISPLA Y OPTION] menu On the menu screen, select [DISPLA Y OPTION] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 97 Adjusting the color matching using a colorimeter Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], [GREEN], [BLUE], [CY AN], [MAGENT A], [YELLOW], or [WHITE] to desired colors.
Chapter 4 Settings — [DISPLA Y OPTION] menu 98 - ENGLISH 3) Press qw to switch the [SCREEN FORMA T] item. f The items will switch each time you press the button. Model No. [SCREEN FORMA T] Range when [SCREEN POSITION] is selected PT -DZ13KU, PT-DZ10KU [16:10] Cannot be adjusted.
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 99 2) Press the <ENTER> button. f The [AUTO SETUP] screen is displayed. 3) Press as to select [POSITION ADJUST]. 4) Press qw to switch the item. [OFF] Does not perform automatic adjustment.
Chapter 4 Settings — [DISPLA Y OPTION] menu 100 - ENGLISH [DVI-D IN] Switch the setting when the external device is connected to the <DVI-D IN> terminal of the projector and the image is not projected correctly . 1) Press as to select [DVI-D IN].
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 101 Setting [SDI LINK] (Only for PT -DZ13KU, PT-DS12KU) 1) Press as to select [SDI IN]. 2) Press the <ENTER> button. f The [SDI IN] screen is displayed. 3) Press as to select [SDI LINK].
Chapter 4 Settings — [DISPLA Y OPTION] menu 102 - ENGLISH [ON-SCREEN DISPLA Y] Set the on-screen display . Setting [OSD POSITION] Set the position of the menu screen (OSD). 1) Press as to select [ON-SCREEN DISPLA Y]. 2) Press the <ENTER> button.
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 103 Note f Even if [OSD MEMORY] is set to [ON], the cursor position will not be held when the <MAIN POWER> switch of the projector body is turned <OFF>.
Chapter 4 Settings — [DISPLA Y OPTION] menu 104 - ENGLISH [ST ARTUP LOGO] Set the logo display when the power is turned on. 1) Press as to select [ST ARTUP LOGO]. 2) Press qw to switch the item. f The items will switch each time you press the button.
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 105 [SHUTTER SETTING] Set image fade-in and fade-out at opening and closing of the shutter . Set automatic opening and closing of the shutter when power is turned on. Setting [F ADE-IN] or [F ADE-OUT] 1) Press as to select [SHUTTER SETTING].
Chapter 4 Settings — [DISPLA Y OPTION] menu 106 - ENGLISH 5) Press the <ENTER> button to switch the Select line to either luminance, red, green, or blue. f Line selection items switch each time the <ENTER> is pressed only when the waveform monitor is displayed.
Chapter 4 Settings — [DISPLA Y OPTION] menu ENGLISH - 107 [CUT OFF] Each red, green, and blue color component can be removed. 1) Press as to select [CUT OFF]. 2) Press the <ENTER> button. f The [CUT OFF] screen is displayed. 3) Press as to select [RED], [GREEN], or [BLUE].
Chapter 4 Settings — [PROJECTOR SETUP] menu 108 - ENGLISH [PROJECT OR SETUP] menu On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 109 [COOLING CONDITION] Change the fan control depending on the direction of projection. Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] normally . Using the projector with incorrect setting may shorten the life of the lamp.
Chapter 4 Settings — [PROJECTOR SETUP] menu 1 10 - ENGLISH 3) Press the <ENTER> button. Note f For a certain time after [LAMP SELECT] is switched, [LAMP SELECT] cannot be switched again, because the speed of the lamp replacement cycle will increase.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 1 1 1 [LAMP POWER] Switch the brightness of the lamp according to the operating environment of the projector or the purpose. 1) Press as to select [LAMP POWER]. 2) Press qw to switch the item.
Chapter 4 Settings — [PROJECTOR SETUP] menu 1 12 - ENGLISH 5) Press as to select [MODE]. 6) Press qw to switch the item. f The items will switch each time you press the button. [OFF] Does not correct the brightness of the screen by the brightness sensor .
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 1 13 Note f When [MODE] in [BRIGHTNESS CONTROL SETUP] is set to [AUTO] or [PC], keep the shutter open for at least two minutes to perform the brightness sensor calibration after completed the [BRIGHTNESS CONTROL SETUP] setting.
Chapter 4 Settings — [PROJECTOR SETUP] menu 1 14 - ENGLISH When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to [AUTO] and [LINK] is set from [GROUP A] to [GROUP D] The screen shows the status of the brightness control of synchronized projectors (up to eight units), including the projector being controlled through the on-screen menu.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 1 15 Brightness control adjustment procedure example The steps exemplify an adjustment to link the brightness of eight projectors connected in a network. 1) Connect all projectors to the hub using LAN cables.
Chapter 4 Settings — [PROJECTOR SETUP] menu 1 16 - ENGLISH [SCHEDULE] Set the command execution schedule for each day of the week. Enabling/disabling the schedule function 1) Press as to select [SCHEDULE]. 2) Press qw to switch the item. f The items will switch each time you press the button.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 1 17 [COMMAND] Detailed settings of [COMMAND] Description [INPUT] [VIDEO] Switches the input to VIDEO. [RGB1] Switches the input to RGB1. [RGB2] Switches the input to RGB2. [DVI-D] Switches the input to DVI-D.
Chapter 4 Settings — [PROJECTOR SETUP] menu 1 18 - ENGLISH [HDMI] Sets the input to HDMI. [SDI1] *1 /[SDI] *2 Sets the input to SDI/SDI1. [SDI2] *1 Sets the input to SDI2. *1 Only for PT -DZ13KU, PT-DS12KU *2 Only for PT -DZ10KU [RS-232C] Set the communication conditions of the <SERIAL IN>/<SERIAL OUT> terminal.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 1 19 2) Press the <ENTER> button. f The [RS-232C] screen is displayed. 3) Press as to select [RESPONSE(ID ALL)]. 4) Press qw to switch the item. [ON] Returns the response when the ID setting is ALL.
Chapter 4 Settings — [PROJECTOR SETUP] menu 120 - ENGLISH [REMOTE2 ST A TUS] Displays the control status of the REMOTE2. [AC VOL T AGE] Displays the status of the AC voltage. [COOLING CONDITION] Displays the set cooling conditions. When [AUTO] is set, automatically recognized result is displayed.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 121 f When [USER] is selected, proceed to Step 3) . 3) Press the <ENTER> button. 4) Press as to select one from [PIN2] to [PIN8], and press qw to switch the setting. [FUNCTION BUTTON] Set the functions of the <FUNC> button on the remote control.
Chapter 4 Settings — [PROJECTOR SETUP] menu 122 - ENGLISH 2) Press the <ENTER> button. f The [DA TE AND TIME] screen is displayed. 3) Press as to select [ADJUST CLOCK]. 4) Press the <ENTER> button. f The [ADJUST CLOCK] screen is displayed.
Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 123 Loading the lens position 1) Press as to select [LENS MEMOR Y]. 2) Press the <ENTER> button. 3) Press as to select [LENS MEMOR Y LOAD]. 4) Press the <ENTER> button. f The [LENS MEMOR Y LOAD] screen is displayed.
Chapter 4 Settings — [PROJECTOR SETUP] menu 124 - ENGLISH f If you press asqw to select [CANCEL] and then press the <ENTER> button, the changed name will not be registered. f If you press asqw to select [DEF AUL T] and press the <ENTER> button, the changed name will not be registered and the default name will be used.
Chapter 4 Settings — [P IN P] menu ENGLISH - 125 [P IN P] menu On the menu screen, select [P IN P] from the main menu, and select an item from the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [P IN P] menu 126 - ENGLISH 12) If [CLOCK PHASE] is selected in Step 6), press qw to make adjustment. 13) Press as to select [FRAME LOCK]. 14) Press qw to switch the item. [MAIN WINDOW] Set frame lock to the input signal set in the main window.
Chapter 4 Settings — [TEST P A TTERN] menu ENGLISH - 127 [TEST P A TTERN] menu On the menu screen, select [TEST P A TTERN] from the main menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen. f Press qw to switch.
Chapter 4 Settings — [SIGNAL LIST] menu 128 - ENGLISH [SIGNAL LIST] menu On the menu screen, select [SIGNAL LIST] from the main menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen. r Registered signal details A1 (1-2) When the address number (A1, A2, .
Chapter 4 Settings — [SIGNAL LIST] menu ENGLISH - 129 f T o cancel the deletion, press the <MENU> button to return to the [REGISTERED SIGNAL LIST] screen.
Chapter 4 Settings — [SIGNAL LIST] menu 130 - ENGLISH Sub memory The projector has a sub memory function that can register the multiple image adjustment data, even if it is recognized as the same signal by the frequency or format of the synchronization signal source.
Chapter 4 Settings — [SECURITY] menu ENGLISH - 131 [SECURITY] menu On the menu screen, select [SECURITY] from the main menu, and select an item from the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [SECURITY] menu 132 - ENGLISH [DISPLA Y SETTING] Overlap the security message (text or image) over the projecting image. 1) Press as to select [DISPLA Y SETTING]. 2) Press qw to switch the item. f The items will switch each time you press the button.
Chapter 4 Settings — [SECURITY] menu ENGLISH - 133 2) Press the <ENTER> button. f The [CONTROL DEVICE SETUP] screen is displayed. 3) Press as to select [CONTROL P ANEL] or [REMOTE CONTROL]. 4) Press the <ENTER> button. 5) Press as to select [CONTROL P ANEL] or [REMOTE CONTROL].
Chapter 4 Settings — [SECURITY] menu 134 - ENGLISH 4) Press asqw to select [OK], and press the <ENTER> button. f T o cancel, select [CANCEL]. Attention f The initial password is “AAAA” by the factory default or when [ALL USER DA T A] in [INITIALIZE] ( x page 124) is executed.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 135 [NETWORK] menu On the menu screen, select [NETWORK] from the main menu, and select an item from the sub- menu. Refer to “Navigating through the menu” ( x page 65) for the operation of the menu screen.
Chapter 4 Settings — [NETWORK] menu 136 - ENGLISH 4) Press as to select [STORE], and press the <ENTER> button. 5) When the confirmation screen is displayed, press qw to select [OK], and press the <ENTER> button. [NETWORK ST A TUS] Display the status of the projector network.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 137 Name and function of network function parts 3 2 1 1 LAN LINK/ACT lamp (green) Lights on when connected. Flashes when transmitting/receiving data. 2 <LAN> terminal (10Base-T/100Base-TX) Used to connect the LAN cable here.
Chapter 4 Settings — [NETWORK] menu 138 - ENGLISH Note f If you use a web browser to control the projector , set [WEB CONTROL] to [ON] in [NETWORK CONTROL] ( x page 135). f Do not perform setting or control simultaneously by starting up multiple web browsers.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 139 [Projector status] page Click [Status] → [Projector status]. Display the status of the projector for the following items. 14 15 16 6 7 8 9 1 2 3 4 17 10 5 11 12 13 1 [PROJECTOR TYPE] Displays the type of the projector .
Chapter 4 Settings — [NETWORK] menu 140 - ENGLISH Error information page When [Error (Detail)] or [W arning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error/warning details.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 141 [Network status] page Click [Status] → [Network status]. The current network setting status is displayed.
Chapter 4 Settings — [NETWORK] menu 142 - ENGLISH [Basic control] page Click [Projector control] → [Basic control]. 1 2 5 3 4 1 [POWER] T urns on/off the power . 2 [SHUTTER] Switches the setting whether to use the shutter function (closing/opening of the shutter).
Chapter 4 Settings — [NETWORK] menu ENGLISH - 143 [Network cong] page Click [Detailed set up] → [Network cong]. f Click [Network cong] to display the [CAUTION!] screen. f The current settings are displayed by pressing the [Next] button.
Chapter 4 Settings — [NETWORK] menu 144 - ENGLISH [Adjust clock] page Click [Detailed set up] → [Adjust clock]. 1 2 3 4 5 6 7 1 [Time Zone] Select the time zone. 2 [Set time zone] Updates the time zone setting. 3 [NTP SYNCHRONIZA TION] Set to [ON] to adjust the date and time automatically .
Chapter 4 Settings — [NETWORK] menu ENGLISH - 145 [E-mail set up] page When there is a problem or the runtime of a lamp reaches a set value, an E-mail can be sent to preset E-mail addresses (up to two addresses). Click [Detailed set up] → [E-mail set up].
Chapter 4 Settings — [NETWORK] menu 146 - ENGLISH 8 7 9 8 7 7 [E-MAIL ADDRESS 1], [E-MAIL ADDRESS 2] Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used. 8 Settings of the conditions to send E-mail Select the conditions to send E-mail.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 147 [Authentication set up] page Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail. Click [Detailed set up] → [Authentication set up]. 1 2 3 4 5 6 7 8 1 [Auth] Select the authentication method specied by your Internet service provider .
Chapter 4 Settings — [NETWORK] menu 148 - ENGLISH Contents of E-mail sent Example of E-mail sent when E-mail is set The following E-mail is sent when the E-mail settings have been established.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 149 Example of the E-mail sent for an error The following E-mail is sent when an error has occurred.
Chapter 4 Settings — [NETWORK] menu 150 - ENGLISH [Change password] page Click [Change password]. 1 2 3 1 [Administrator] Used to change the setting of the [Administrator]. 2 [User] Used to change the setting of the [User]. 3 [Next] Used to change the setting of the password.
Chapter 4 Settings — [NETWORK] menu ENGLISH - 151 [User] account 1 2 3 5 4 1 [Account] Displays the account to change. 2 [New][User name] Enter the desired new user name. (Up to 16 characters in single byte) 3 [New][Password] Enter the desired new password.
Chapter 4 Settings — [NETWORK] menu 152 - ENGLISH Control page 1 2 3 4 5 6 7 1 [T ools][Info][Help] T abs for selecting the setting, information, or help page of the projector . 2 [POWER] T urns on/off the power . 3 [SHUTTER] Switches the setting whether to use the shutter function (closing/opening of the shutter).
Chapter 4 Settings — [NETWORK] menu ENGLISH - 153 [Info] page Click [Info] on the control page. 4 5 6 7 1 2 3 8 1 [Projector Name] Displays the projector name. 2 [Mac Address] Displays the MAC address. 3 [Lamp Hours] Displays the runtime of the lamps (converted value).
154 - ENGLISH Chapter 5 Maintenance This chapter describes methods of inspection when there are problems, maintenance, and replacement of the units..
Chapter 5 Maintenance — Lamp/temperature/lter indicators ENGLISH - 155 Lamp/temperature/lter indicators When an indicator lights up If a problem should occur inside the projector , the lam.
Chapter 5 Maintenance — Lamp/temperature/lter indicators 156 - ENGLISH T emperature indicator <TEMP> Indicator status Lighting in red Flashing in red (2 times) Flashing in red (3 times) Status W arm-up status Internal temperature is high (warning).
Chapter 5 Maintenance — Maintenance/replacement ENGLISH - 157 Maintenance/replacement Before performing maintenance/replacement f Make sure to turn off the power before maintaining or replacing the unit. ( x pages 52, 55) f When switching off the projector , make sure to follow the procedures in “Switching off the projector” ( x page 55).
Chapter 5 Maintenance — Maintenance/replacement 158 - ENGLISH Cleaning the air lter unit Remove the air lter unit beforehand with the previously described procedure of “Removing the air lter unit”. Fig. 1 Fig. 2 1) W ash the air filter unit.
Chapter 5 Maintenance — Maintenance/replacement ENGLISH - 159 Replacing the unit Air lter unit If dirt does not come off even after the unit is maintained, it is time for the unit to be replaced. The Replacement Filter Unit (Model No.: ET -EMF320) is an optional accessory .
Chapter 5 Maintenance — Maintenance/replacement 160 - ENGLISH Note f The model numbers of accessories and optional accessories are subject to change without prior notice.
Chapter 5 Maintenance — Maintenance/replacement ENGLISH - 161 How to replace the lamp unit Attention f When the projector is mounted on the ceiling, do not conduct work while your face is near the lamp unit. f Do not remove or loosen the screws other than specied ones when replacing the lamp unit.
Chapter 5 Maintenance — Maintenance/replacement 162 - ENGLISH 5) Use a Phillips screwdriver to firmly tighten the lamp unit fixing screws (x2 each). f Make sure to attach the lamp unit securely . 6) Attach the lamp unit cover . i) Close the lamp unit cover in Step 2) in the reverse order .
Chapter 5 Maintenance — T roubleshooting ENGLISH - 163 T roubleshooting Review the following points. For details, see the corresponding pages. Problems Points to be checked Page Power does not turn on.
Chapter 5 Maintenance — T roubleshooting 164 - ENGLISH Problems Points to be checked Page Left and right images are reversed (not showing properly). f Are the devices synchronized? Check the 3D eyewear settings. ― f Change the [LEFT/RIGHT SW AP] setting of [3D SETTINGS].
ENGLISH - 165 Chapter 6 Appendix This chapter describes specications and after-sales service for the projector ..
Chapter 6 Appendix — T echnical information 166 - ENGLISH T echnical information PJLink protocol The network function of this projector supports the PJLink class 1, and the PJLink protocol can be used to perform projector setting and projector status query operations from a computer .
Chapter 6 Appendix — T echnical information ENGLISH - 167 PJLink security authentication The password used for PJLink is the same as that of the password set for web control. When using the projector without security authentication, do not set a password for web control.
Chapter 6 Appendix — T echnical information 168 - ENGLISH r Error response String Details T ermination symbol Message “ERR1” Undened control command (CR) 0x0d “ERR2” Out of parameter .
Chapter 6 Appendix — T echnical information ENGLISH - 169 r Error response String Details T ermination symbol Message “ERR1” Undened control command (CR) 0x0d “ERR2” Out of parameter .
Chapter 6 Appendix — T echnical information 170 - ENGLISH D-Sub 9-pin (male) Outside view Pin No. Signal name Details (6) (9) (1) (5) (1) ― NC (2) RXD Received data (3) TXD T ransmitted data (.
Chapter 6 Appendix — T echnical information ENGLISH - 171 Attention f If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. T ry sending or receiving any command after 60 seconds.
Chapter 6 Appendix — T echnical information 172 - ENGLISH Control command The following table lists the commands that can be used to control the projector using a computer . r Projector control command Command Details Parameter/response string Remark (parameter) PON Power on ― T o check if the power is on, use the “Power query” command.
Chapter 6 Appendix — T echnical information ENGLISH - 173 r Lens control command Command Sub command Details Remark VXX LNSI2 Lens H shift +00000 = Fine adjustment 1+, +00001 = Fine adjustment 1.
Chapter 6 Appendix — T echnical information 174 - ENGLISH T wo-window display combination list Sub window RGB1 RGB2 VIDEO input Main window RGB Movie *3 Y/C input RGB Movie *3 RGB1 RGB ―――.
Chapter 6 Appendix — T echnical information ENGLISH - 175 Upgrade Kit (Only for PT -DZ13KU, PT-DS12KU) If the optional Upgrade Kit (Model No.: ET -UK20) is applied, the following functions are extended.
Chapter 6 Appendix — T echnical information 176 - ENGLISH Mode Resolution (Dots) Scanning freq. Dot clock freq. (MHz) Format Plug and play *1 Horizontal (kHz) V ertical (Hz) RGB2 DVI-D HDMI EDID1 EDID2 EDID3 SVGA 800 x 600 35.2 56.3 36.0 R/D/H l ― lll 800 x 600 37.
Chapter 6 Appendix — T echnical information ENGLISH - 177 Mode Resolution (Dots) Scanning freq. Dot clock freq. (MHz) Format Plug and play *1 Horizontal (kHz) V ertical (Hz) RGB2 DVI-D HDMI EDID1 EDID2 EDID3 1920 x 1080 1 920 x 1 080 55.6 49.9 141.
Chapter 6 Appendix — T echnical information 178 - ENGLISH 3D compatible signal Resolution (Dots) Scanning freq. Dot clock freq. (MHz) HDMI DVI-D Horizontal (kHz) V ertical (Hz) 1 2 *1 3 2 *1 345 MXGA 1 152 x 864 53.7 60.0 81.6 ― ― ― l ――― 1280 x 720 1 280 x 720 37.
Chapter 6 Appendix — T echnical information ENGLISH - 179 3D compatible signal Resolution (Dots) Scanning freq. Dot clock freq. (MHz) RGB1/RGB2 SDI1/SDI2 7 8 9 Horizontal (kHz) V ertical (Hz) 2 *1 3 4 5 2 *1 3 4 6 *3 10 10 10 750 (720)/60p 1 280 x 720 45.
Chapter 6 Appendix — Specications 180 - ENGLISH Specications The specications of the projector are as follows. Power supply AC 120 V , 50 Hz/60 Hz Power consumption PT -DZ13KU 1 000 W (9.3 A) PT -DS12KU, PT-DW1 1KU 980 W (9.1 A) PT -DZ10KU 925 W (9 A) 0.
Chapter 6 Appendix — Specications ENGLISH - 181 r Applicable scanning frequency Refer to “List of compatible signals” ( x page 175) for the types of video signals that can be used with the projector . For video signal (including Y/C signal) Horizontal: 15.
Chapter 6 Appendix — Specications 182 - ENGLISH r T erminal <RGB 1 IN> terminal 1 set (BNC x 5 (RGB/YP B P R /YC B C R /YC x 1)) RGB signal 0.
Chapter 6 Appendix — Dimensions ENGLISH - 183 Dimensions Unit: mm 540 (21-1/4") 200 (7-7/8") 8.5 (11/32") 100 (3-15/16") 462 (18-3/16") 26 (1-1/32") 530 (20-7/8") 468 (18-7/16") * Actual dimensions may differ depending on the product.
Chapter 6 Appendix — Precautions for Ceiling Mount Bracket for Projectors 184 - ENGLISH Precautions for Ceiling Mount Bracket for Projectors f When installing the projector to a ceiling, be sure to use the specied optional Ceiling Mount Bracket for Projectors (Model No.
Index ENGLISH - 185 0 – 9 [3D COLOR MA TCHING] 93 [3D FRAME DELA Y] 94 [3D INPUT FORMA T] 92 [3D PICTURE BALANCE] 93 [3D SAFETY PRECAUTIONS] 95 [3D SETTINGS] 68, 91 [3D SIMUL INPUT SETTING] 92 [3D S.
Index 186 - ENGLISH U [UNIFORMITY] 104 Upgrade Kit 175 V <VIDEO> button Projector body 26, 62 Remote control 24, 62 W [W A VEFORM MONITOR] 105 Z [ZOOM] 8 0 <ZOOM> button Remote control 24,.
Panasonic System Communications Company of North America One Panasonic Way 2F-13, Secaucus, NJ 07094 TEL: (877) 803 - 8492 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 TEL: (905) 624 - 5010 Panasonic Corporation Web Site : http://panasonic.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Panasonic PT-DZ10KU è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Panasonic PT-DZ10KU - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Panasonic PT-DZ10KU imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Panasonic PT-DZ10KU ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Panasonic PT-DZ10KU, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Panasonic PT-DZ10KU.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Panasonic PT-DZ10KU. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Panasonic PT-DZ10KU insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
