Manuale d’uso / di manutenzione del prodotto R10-A2P4 del fabbricante Asus
Vai alla pagina of 34
1U Rackmount Chassis Kit R10-A2P4 User Guide.
ii Copyright © 2004 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a r.
iii Contents Notices ........................................................................................... iv Safety information ........................................................................... v About this guide .....................
iv Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
v Safety infor mation Electrical Safety • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
vi Audience This user guide is intended for system integrators, and experienced users with at least basic knowledge of configuring a server . Contents This guide contains the following parts: 1. Chapter 1: Product Introduction This chapter describes the general features of the chassis kit.
1-1 ASUS R10-A2P4 1U rackmount chassis kit This chapter describes the general features of the chassis kit. It includes sections on front panel and rear panel specifications.
Chapter 1: Product introduction 1-2 1 . 1 System package contents Check your ASUS R10-A2P4 package for the following items. Contact your dealer immediately if any of the items is damaged or missing.
ASUS R10-A2P4 1U rackmount chassis kit 1-3 1 .3 Rear panel features The rear panel includes the expansion slot, system power socket, and rear fans. The middle part includes the I/O shield with openings for the rear panel connectors on the motherboard.
Chapter 1: Product introduction 1-4 1 .4 Internal featur es The chaais includes the basic components as shown. 1. PCI-X riser card bracket 2. Rear fans 3. Power supply 4. Device fan 5. System fans 6. SA T A backplane 7. HDD tray 1 8. HDD tray 2 9. Optical drive The chassis kit does not include a floppy disk drive.
ASUS R10-A2P4 1U rackmount chassis kit 1-5 1 .5 LED information 1.5.1 Front panel LEDs 1.5.2 Rear panel LEDs ACT/LINK LED SPEED LED Status Description Status Description OFF No link OFF 10Mbps connect.
Chapter 1: Product introduction 1-6.
ASUS R10-A2P4 1U rackmount chassis kit 2-1 This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
Chapter 2: Hardware setup 2-2 2. 1 Preparation Before proceeding, prepare everything that you might need to facilitate installation. 2.1.1 T ools to use 1. Phillips head screw driver 2. Flat head screw driver 2.1.2 System components and devices to install The following items are the basics that you need to install into the chassis kit.
2-3 ASUS R10-A2P4 1U rackmount chassis kit 2.2 Removing and installing the chassis cover 2.2.1 Removing the cover 1. Use a Phillips screwdriver to remove the screw on each front end of the top cover . 3. Firmly hold the cover and slide it toward the rear panel for about half an inch until it is disengaged from the chassis.
Chapter 2: Hardware setup 2-4 2.2.2 Installing the cover 1. Position the cover on top of the chassis with the thumbscrews on the rear , and leaving a gap of about half an inch from the front panel. 3. Slide the cover toward the front until it snaps in place.
2-5 ASUS R10-A2P4 1U rackmount chassis kit 2.3 Motherboard ins tallation 2.3.1 Motherboard dimensions This chassis kit supports an ASUS motherboard that measures 12 x 10.5 inches (30.48 x 26.67 cm). Motherboards of smaller sizes will fit into the chassis.
Chapter 2: Hardware setup 2-6 2.3.2 Placement direction and screw holes Align the holes on the motherboard (indicated by white circles in the picture below) to the corresponding standoffs on the motherboard metal plate inside the chassis. Place screws through the designated holes to secure the motherboard to the chassis.
2-7 ASUS R10-A2P4 1U rackmount chassis kit 2.3.3 Installing the motherboard T o install the motherboard: 1. Firmly hold the riser card bracket, then pull it up to detach it from the chassis. 3. Firmly hold the motherboard as shown, and place the side with the CPU sockets near the system fans.
Chapter 2: Hardware setup 2-8 5. Match the motherboard holes with the chassis standof fs. 6. Secure the motherboard with screws. Refer to the motherboard user guide for the specific number of screws that you need to use. 4. Fit the rear panel connectors to the I/O shield openings on the chassis rear .
2-9 ASUS R10-A2P4 1U rackmount chassis kit 2.4 Hard disk dr ives T o install a SA T A HDD: 1. Release a drive tray by pushing the spring lock to the right, then pulling the tray lever outward. The drive tray ejects slightly after you pull out the lever .
Chapter 2: Hardware setup 2-10 5. Carefully insert the drive tray and push it all the way to the depth of the bay until just a small fraction of the tray edge protrudes. 6. Push the tray lever until it clicks, and secures the drive tray in place. The drive tray is correctly placed when its front edge aligns with the bay edge.
2-11 ASUS R10-A2P4 1U rackmount chassis kit 2.5 Expansion slot The chassis comes with a riser card bracket. Y ou need to remove the bracket if you wish to install an PCI-X expansion card. T o install a PCI-X card: 1. Firmly hold a riser card bracket, then pull it up to detach it from the PCI-X slot on the motherboard.
Chapter 2: Hardware setup 2-12 5. Make sure that the golden connectors completely fit the slot and the bracket aligns with the rear panel. 6. Connect the cable(s) to the card, if applicable. 4. Install the riser card bracket with the card into the PCI-X slot on the motherboard.
2-13 ASUS R10-A2P4 1U rackmount chassis kit 2.6 Removable components Y ou may need to remove previously installed system components when installing or removing system devices, or when you need to replace defective components. This section tells how to remove the following components: 1.
Chapter 2: Hardware setup 2-14 2.6.3 Power supply module T o uninstall the power supply module: 1. Disconnect all the power cables connected to the motherboard and other system devices. 3. Slide the power supply backward for about half an inch, then carefully lift it out from the chassis.
2-15 ASUS R10-A2P4 1U rackmount chassis kit 2.6.4 Optical drive T o uninstall the optical drive: 1. Disconnect the power and signal cables connected to the rear of the optical drive. 2. Use a Phillips (cross) screwdriver to remove the two screws that secure the meal bracket on the side of the optical drive.
Chapter 2: Hardware setup 2-16 T o install an optical drive: 1. From the front panel, insert the rear end of the optical drive into the 5.25-inch drive bay . 2. Place the metal bracket parallel to the side of the optical drive, matching its two pegs with the lower holes, and the bracket holes with the standof fs on the base of the chassis.
2-17 ASUS R10-A2P4 1U rackmount chassis kit 2.6.5 Motherboard T o uninstall the motherboard: 1. Disconnect all the power and signal cables connected to the motherboard. 2. Uninstall all the devices from the motherboard including the CPU and heatsink, riser card brackets, and DDR DIMMs.
Chapter 2: Hardware setup 2-18 2.7 SA T A backplane cabling Ensure that the F AN1 connector on the SA T A backplane and the CPU_F AN2 on the motherboard are connected via the 3-pin fan cable. The fan RPM (rotations per minute) are monitored and automatically adjusted through this feature.
ASUS R10-A2P4 1U rackmount chassis kit 2-1 This chapter tells how to install the system to a rack. Chapter 3 Rackmounting.
Chapter 3: Rackmounting 3-2 3. 1 Rackmount rail kit items If you have the rackmount rail kit, it contains two pairs of rails (one pair for each side of the barebone system), and eight (8) pairs of nut-and-bolt type screws. 3.2 Rack r ails assembl y T o assemble the rack rails: 1.
3-3 ASUS R10-A2P4 1U rackmount chassis kit 3.3 Attaching the rails to t he r ack T o attach the rails to the rack: 1. Select one unit of space (1U) on the rack where you wish to install the barebone server . 2. Remove the screws from the 1U space on the rack front.
Chapter 3: Rackmounting 3-4 3.4 Rackmounting the ser ver T o mount the server to the rack: 1. Firmly hold the server on both sides and insert the rear panel side to the front end of the rack rail, the.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Asus R10-A2P4 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Asus R10-A2P4 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Asus R10-A2P4 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Asus R10-A2P4 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Asus R10-A2P4, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Asus R10-A2P4.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Asus R10-A2P4. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Asus R10-A2P4 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
