Manuale d’uso / di manutenzione del prodotto P4B533-M del fabbricante Asus
Vai alla pagina of 128
Motherboard P4B533-M User Guide.
ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents Contents ......................................................................................... iii FCC/CDC statements ..................................................................... vi Safety information ...............
iv Safeguards Contents 2.6 Expansion slots ................................................................ 2-13 2.6.1 Installing an expansion card ................................ 2-13 2.6.2 Configuring an expansion card ............................ 2-13 2.
v Contents Chapter 5: Software support 5.1 Install an operating system ................................................. 5-1 5.2 Support CD information ...................................................... 5-1 5.2.1 Running the support CD ...........
vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains the information you need when installing the ASUS P4B533-M motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the P4B533-M motherboard.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
xi P4B533-M specifications summar y CPU Chipset Front Side Bus (FSB) Memory Expansion slots IDE Audio (optional) Special features Rear panel I/O Internal I/O BIOS features Industry standard Manageabil.
xii Form Factor Support CD contents Micro-A TX form factor: 9.6 in x 9.6 in (24.5 cm x 24.5 cm) Device drivers ASUS PC Probe ASUS LiveUpdate T rend Micro ™ PC-cillin 2002 anti-virus software CyberLink Power Player SE, V ideoLive Mail P4B533-M specifications summar y * Specifications are subject to change without notice.
Chapter 1 This chapter describes the features of the P4B533-M motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
ASUS P4B533-M motherboard Chapter summar y 1.1 W elcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................
ASUS P4B533-M motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® P4B533-M motherboard! The ASUS P4B533-M motherboard delivers a host of new features and latest technologies mak.
1-2 Chapter 1: Product introduction 1 .3 Special features 1.3.1 Product highlights Latest processor technology The P4B533-M motherboard supports the latest Intel ® Pentium ® 4 Processor via a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on 0.
ASUS P4B533-M motherboard user guide 1-3 1.3.2 V alue-added solutions Concurrent PCI This feature allows multiple PCI transfers from PCI master buses to the memory and processor . T emperature, fan, and voltage monitoring The CPU temperature is monitored by the ASUS ASIC through the CPU ’ s internal diode to prevent overheating and damage.
1-4 Chapter 1: Product introduction 1 .4 Motherboard over view Before you install the P4B533-M motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades.
ASUS P4B533-M motherboard user guide 1-5 2 3 4 5 7 13 16 14 1 8 6 9 10 15 19 12 17 11 18 20 21 30 29 28 26 23 24 25 22 27.
1-6 Chapter 1: Product introduction 1.4.2 Core specifications A TX 12V connector . This power connector is for the 4-pin 12V plug from an A TX 12V power supply . CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF) socket for the Intel ® Pentium ® 4 Processor , with 533/400MHz system bus that allows 4.
ASUS P4B533-M motherboard user guide 1-7 ASUS ASIC. This chip performs multiple system functions that include hardware and system voltage monitoring. South bridge controller .
1-8 Chapter 1: Product introduction Parallel port. This 25-pin port connects a parallel printer , a scanner , or other devices. RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. (on LAN models only) Line In jack.
Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
ASUS P4B533-M motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) .
ASUS P4B533-M motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4B533-M uses the micro- A TX form factor that measures 9.
2-2 Chapter 2: Hardware information 2.2 Motherboard layout The audio, LAN, and 1394 features are optional. These components are grayed out in the above motherboard layout.
ASUS P4B533-M motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for t he Intel Pentium 4 Processor in the 478-pin package with 512KB L2 cache on 0.
ASUS P4B533-M motherboard user guide 2-5 2.4.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard.
2-6 Chapter 2: Hardware information 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever . 4. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation.
ASUS P4B533-M motherboard user guide 2-7 2.4.3 Installing the heatsink and fan The Intel ® Pentium ® 4 Processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Retention Module Base CPU Heatsink The retention module base is already installed on the motherboard upon purchase.
2-8 Chapter 2: Hardware information 2. Position the fan with the retention mechanism on top of the heatsink. Align and snap the four hooks of the retention mechanism to the holes on each corner of the module base. Keep the retention locks lifted upward while fitting the retention mechanism to the module base.
ASUS P4B533-M motherboard user guide 2-9 2.4.4 Connecting the CPU fan cable When the fan, heatsink, and the retention mechanism are in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. 3. Push down the locks on the retention mechanism to secure the heatsink and fan to the module base.
2-10 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with two Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 2GB system memory using 184-pin unbuffered ECC or non-ECC PC2100/1600 DIMMs.
ASUS P4B533-M motherboard user guide 2-11 2.5.2 Memory configurations 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
2-12 Chapter 2: Hardware information 2.5.4 Removing a DIMM Follow these steps to remove a DIMM. 1. Simultaneously press the retaining clips outward to unlock the DIMM. Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
ASUS P4B533-M motherboard user guide 2-13 2.6 Expansion slots In the future, you may need to install expansion cards. The motherboard has three PCI slots and one Accelerated Graphics Port (AGP) slot. The following sub-sections describe the slots and the expansion cards that they support.
2-14 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (CO.
ASUS P4B533-M motherboard user guide 2-15 2.6.3 PCI slots There are three 32-bit PCI slots in this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot.
2-16 Chapter 2: Hardware information 2.7 Switches and jumpers The motherboard frequency is adjusted through the DIP switches. The white block represents the switch position.
ASUS P4B533-M motherboard user guide 2-17 2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard.
2-18 Chapter 2: Hardware information 1. This feature requires a power supply that can provide at least 1A on the +5VSB lead when these jumpers are set to +5VSB. Otherwise, the system does not power up. 2. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode.
ASUS P4B533-M motherboard user guide 2-19 5. Clear RTC RAM (R200A) These solder points allow you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
2-20 Chapter 2: Hardware information 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors.
ASUS P4B533-M motherboard user guide 2-21 3. IDE connectors (40-1 pin PRI_IDE/SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable.
2-22 Chapter 2: Hardware information 4. A TX power connectors (20-pin A TX_POWER, 4-pin A TX12V) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
ASUS P4B533-M motherboard user guide 2-23 5. CPU and Chassis Fan Connectors (3-pin CPU_F AN, PWR_F AN) The fan connectors support cooling fans of 350mA (4.2 W atts) or a total of 1A (12W) at +12V . Connect the fan cable to the connector matching the black wire to the ground pin.
2-24 Chapter 2: Hardware information 7. USB header (10-1 pin USB20_3) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed.
ASUS P4B533-M motherboard user guide 2-25 9. Infrared module connector (5-pin IR_CON) These connectors support an optional wireless transmitting and receiving infrared module. The module mounts to a small opening on system chassis that support this feature.
2-26 Chapter 2: Hardware information 1 1. GAME/MIDI connector (16-1 pin GAME) (on audio models only) This connector supports a GAME/MIDI module. If your package came with the optional USB 2.0/GAME module, connect the GAME/MIDI cable to this connector .
ASUS P4B533-M motherboard user guide 2-27 13. System panel connector (20-pin P ANEL) This connector is for various system front panel features. See the description of each feature below . ® P4B533-M P4B533-M System Panel Connectors * Requires an A TX power supply .
2-28 Chapter 2: Hardware information • A TX Power Switch / Soft-Off Switch Lead (2-pin PWR) This connector connects a switch that controls the system power . Pressing the power switch turns the system between ON and SLEEP , or ON and SOFT OFF , depending on the BIOS or OS settings.
Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes..
ASUS P4B533-M motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 Powering off the computer ............
ASUS P4B533-M motherboard user guide 3-1 3. 1 St ar ting up for the fir s t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system.
Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS P4B533-M motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-7 4.3 Main Menu .................................................... 4-10 4.4 Advanced Menu .
ASUS P4B533-M motherboard user guide 4-1 4. 1 Managing and updating your BIOS It is recommended that you save a copy of the motherboard’s original BIOS to a bootable floppy disk in case you need to reinstall the original BIOS later .
4-2 Chapter 4: BIOS Setup 5. At the prompt, “ Please Enter File Name for NEW BIOS: _ ” , type in the BIOS file name that you downloaded from the ASUS website, then press <Enter>. EZ Flash will automatically access drive A to look for the file name that you typed.
ASUS P4B533-M motherboard user guide 4-3 4.1.2 Using AFLASH to update the BIOS Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4-4 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears.
ASUS P4B533-M motherboard user guide 4-5 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3.
4-6 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. When the programming is done, the message “Flashed Successfully” appears. 8. Follow the onscreen instructions to continue. If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems.
ASUS P4B533-M motherboard user guide 4-7 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.
4-8 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features.
ASUS P4B533-M motherboard user guide 4-9 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination.
4-10 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59).
ASUS P4B533-M motherboard user guide 4-11 Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>. T ype in a password then press <Enter>.
4-12 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
ASUS P4B533-M motherboard user guide 4-13 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM .
4-14 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity .
ASUS P4B533-M motherboard user guide 4-15 SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system that utilizes internal hard disk drive monitoring technology .
4-16 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes.
ASUS P4B533-M motherboard user guide 4-17 4.4 Advanced Menu CPU/Memory Frequency Ratio [Auto] This field determines whether the memory clock frequency is set to be in synchronous or asynchronous mode with respect to the system frequency . The options that appear in the popup menu vary according to the CPU Frequency (MHz).
4-18 Chapter 4: BIOS Setup PS/2 Mouse Function Control [Auto] The default setting [Auto] allows the system to detect a PS/2 mouse at startup. If a mouse is detected, the BIOS assigns IRQ12 to the PS/2 mouse. Otherwise, IRQ12 can be used for expansion cards.
ASUS P4B533-M motherboard user guide 4-19 4.4.1 Chip Configuration The SDRAM parameters (items 2~5) become configurable only when you set the SDRAM Configuration to [User Defined]. SDRAM CAS Latency [2.5T] This item controls the latency between the DDR SDRAM read command and the time the data actually becomes available.
4-20 Chapter 4: BIOS Setup SDRAM RAS Precharge Delay [3T] This item controls the idle clocks after issuing a precharge command to the DDR SDRAM. It is recommended to keep the default setting for stable system operation. SDRAM Active Precharge Delay [6T] This item controls the number of DDR SDRAM clocks used for DDR SDRAM parameters.
ASUS P4B533-M motherboard user guide 4-21 AGP Capability [4X Mode] This motherboard supports the AGP 4X interface that transfers video data at 1066MB/s. AGP 4X is backward-compatible, so you may keep the default [4X Mode] even if you are using an AGP 1X video card.
4-22 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes.
ASUS P4B533-M motherboard user guide 4-23 Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction.
4-24 Chapter 4: BIOS Setup Slot 1, Slot 2, Slot 3 IRQ [Auto] These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments.
ASUS P4B533-M motherboard user guide 4-25 Primary VGA BIOS [PCI VGA Card] This field allows you to select the primary graphics card. Configuration options: [PCI VGA Card] [AGP VGA Card] Onboard LAN Controller [Enabled] This field allows you to enable or disable the onboard LAN controller .
4-26 Chapter 4: BIOS Setup IRQ XX Reserved [No/ICU] These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. The setting [No/ICU] for an IRQ field indicates that you are using the ISA Configuration Utility (ICU), and that this particular IRQ is NOT required by a legacy ISA card.
ASUS P4B533-M motherboard user guide 4-27 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features.
4-28 Chapter 4: BIOS Setup V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features.
ASUS P4B533-M motherboard user guide 4-29 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system.
4-30 Chapter 4: BIOS Setup Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an A TX power supply that provides at least 1A on the +5VSB lead.
ASUS P4B533-M motherboard user guide 4-31 4.5.2 Hardware Monitor If any of the monitored items is out of range, the following error message appears: “ Hardware Monitor found an error . Enter Power setup menu for details ” . Y ou will then be prompted to “ Press F1 to continue or DEL to enter SETUP ” .
4-32 Chapter 4: BIOS Setup Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or <Space> key , you can promote devices and by using the <-> key , you can demote devices.
ASUS P4B533-M motherboard user guide 4-33 Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Y es] is selected, interrupts may be reassigned by the OS.
4-34 Chapter 4: BIOS Setup 4.7 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
ASUS P4B533-M motherboard user guide 4-35 Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values.
4-36 Chapter 4: BIOS Setup.
Chapter 5 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
ASUS P4B533-M motherboard Chapter summar y 5.1 Install an operating system ........................... 5-1 5.2 Support CD information .................
ASUS P4B533-M motherboard user guide 5-1 5. 1 Inst all an operating system This motherboard supports Windows 98/ME/NT/2000/XP and OS/2 operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
5-2 Chapter 5: Software support 5.2.2 Main menu From the welcome screen, the program takes you directly to the main menu. The main menu displays an image of the motherboard, and the buttons and icons that link you to the software, drivers, utilities, and other information contained in the support CD.
ASUS P4B533-M motherboard user guide 5-3 5.2.3 Software menu The software menu shows the applications and other software that the motherboard supports. The highlighted items indicate that they are available for your motherboard. Simply click on a specific item then follow the installation wizard to install it.
5-4 Chapter 5: Software support Direct X This item installs the Microsoft V8.0a driver . E-Color 3Deep This item installs the 3Deep software. 3Deep is the first application that gives online gamers the competitive edge in multi-player skirmishes. This application removes dark washed-out graphics to deliver true vibrant colors.
ASUS P4B533-M motherboard user guide 5-5 5.2.4 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. The drivers menu is composed of two screens.
5-6 Chapter 5: Software support 5.2.6 ASUS Contact Information Clicking the ASUS Contact Information button displays as stated. Y ou may also find this information on page x of this user guide. 5.2.5 DOS Utility menu The DOS utilities menu includes items that you can run in DOS mode.
ASUS P4B533-M motherboard user guide 5-7 5.2.7 Other information The icons on the left side of the screen give additional information on the motherboard and the contents of the support CD. This section shows the pop-up windows that appear when you click the icons.
5-8 Chapter 5: Software support T echnical Support Form The window displays the ASUS T echnical Support Request Form that you have to fill up when requesting technical support. Readme The window displays the contents of the support CD and a brief description of each in text format.
ASUS P4B533-M motherboard user guide 5-9 5.3 Softwar e information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information.
5-10 Chapter 5: Software support 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file.
ASUS P4B533-M motherboard user guide 5-11 5.3.2 ASUS PC Probe The ASUS PC Probe is a convenient utility to continuously monitor your computer system’s vital components, such as fan rotations, voltages, and temperatures.
5-12 Chapter 5: Software support Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. T emperature Monitor Shows the PC temperature (for supported processors only).
ASUS P4B533-M motherboard user guide 5-13 Settings Lets you set threshold levels and polling intervals or refresh times of the PC ’ s temperature, fan rotation, and voltages. History Lets you record the monitoring activity of a certain component of your PC for future reference.
5-14 Chapter 5: Software support Device Summary Shows a summary of devices present in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules.
ASUS P4B533-M motherboard user guide 5-15 ASUS PC Probe T ask Bar Icon Right clicking the PC Probe icon brings up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring.
5-16 Chapter 5: Software support 5.3.3 E-Color 3Deep The 3Deep color tuner is designed to match your CRT or LCD color monitor and maximize the color quality of all graphical applications. Y ou may also tune your internet applications to match “ true ” internet source colors with the color displayed on the monitor .
ASUS P4B533-M motherboard user guide 5-17 4. Select the color squares that most closely blend and match with the background. 2. Follow the instructions to manually adjust the brightness level of the monitor . 3. Select the faintest of the three colors: blue , red , and green .
5-18 Chapter 5: Software support 6. When a message appears indicating that the tuning process is complete, click Finish . 5. The next step repeats the color matching process to achieve full color quality . 7. Click on the Set Up Now button to connect to the Internet.
Glossary This part lists the technical terms that you may encounter when reading this document..
ASUS P4B533-M motherboard.
ASUS P4B533-M motherboard user guide G-1 1394. 1394 is the IEEE designation for a high performance serial bus that offers data transfers at 100/200/400 Mbps. This serial bus defines both a back plane physical layer and a point-to-point cable-connected virtual bus.
G-2 Glossary Backup. A copy of a file, directory , or volume on a separate storage device from the original. This copy is for the purpose of data retrieval in case the original is accidentally erased, damaged, or destroyed. BIOS (Basic Input/Output System).
ASUS P4B533-M motherboard user guide G-3 CPU (Central Processing Unit). The CPU, also called “Processor ,” actually functions as the “brain” of the computer . It interprets and executes program commands and processes data stored in the system memory .
G-4 Glossary I/O Address. The specific memory location for a particular device. T wo devices cannot share the same I/O address space. IrDA (Infrared Data Association). An internaltional organization that creates and promotes inter-operable, low cost, infrared data interconnection standards that support a walk-up, point-to-point model.
ASUS P4B533-M motherboard user guide G-5 POST (Power On Self T est). When you turn ON the computer , it will first run through the POST , a series of software-controlled diagnostic tests. The POST checks system memory , the motherboard circuitry , the display , the keyboard, the diskette drive, and other I/O devices.
G-6 Glossary System Disk. A system disk contains the core file of an operating system and is used to boot up the operating system. TCP/IP (T ransmission Control Protocol/Internet Protocol). The communications protocol used by the UNIX system and the Internet.
Index This part contains an alphabetical list of the topics found in this document..
ASUS P4B533-M motherboard.
ASUS P4B533-M motherboard user guide I-1 A Accelerated Graphics Port 2-15 Acrobat Reader 5-4 ASUS ASIC 1-9 ASUS EZ Flash 4-1 ASUS iPanel 2-32 ASUS PC Probe 5-12 ASUS Update 5-9 A T API CD-ROM 4-34 Aud.
I-2 Index F Flash EEPROM 1-9 Floppy 3 Mode 4-10 Floppy disk access control 4-24 H Hard Disk Drives (HDDs) CHS Capacity 4-14 Cylinders 4-14 Heads 4-14 LBA Capacity 4-14 Primary/Secondary Master 4-12 Pr.
ASUS P4B533-M motherboard user guide I-3 RAS Precharge Delay 4-22 RAS to CAS Delay 4-21 Serial Ports 1-10, 4-24 SMAR T Monitoring 4-15 Super I/O controller 1-9 Support CD 5-1 ASUS Update 5-9 DOS Utili.
I-4 Index.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Asus P4B533-M è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Asus P4B533-M - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Asus P4B533-M imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Asus P4B533-M ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Asus P4B533-M, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Asus P4B533-M.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Asus P4B533-M. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Asus P4B533-M insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
