Manuale d’uso / di manutenzione del prodotto 200 del fabbricante Orion Car Audio
Vai alla pagina of 44
XTREME 200/400.4 O WNER ’ S M ANUAL H IGH P ERFORMANCE C AR A UDIO.
TABLE OF CONTENTS INTRODUCTION 1 WARRANTY 4 SPECIFICA TIONS 6 TECHNICAL DESIGN FEA TURES 8 SYSTEM PLANNING 10 INST ALLA TION 18 POWER CONNECTIONS 19 SPEAKER CONNECTIONS 20 OUTPUT CONFIGURA TIONS 27 4-.
Thank you for your purchase of ORION’ s XTREME amplifier . Each ORION amplifier is designed to be the leader in its class of fering the most power , advanced features and ease of use. The ORION XTREME amplifiers are designed as the best “affordable high end” car audio amplifier money can buy .
ABOUT THIS MANUAL This manual is divided into different sections for dif ferent needs. Whether you are the owner , salesperson or installer , we hav e devoted sections of this manual to answer your questions.
(1) XTREME amplifier (1) 8 gauge power and ground connector (1) 14 gauge speaker and remote connector (4) #8 self-tapping black Phillips pan head screws (1) XTREME installation and operation manual WH.
WARRANTY ORION Industries Inc. warrants this product to be free from defects in material and workmanship under the following terms: Parts and Labor are warranted for a period of 3 years IF: a. The product is purchased from an Authorized ORION Dealer b.
This warranty is in effect for the original purchaser only . ORION will pay for labor and material expense for covered items. ORION does not cover removal or installation charges, payment of shipping charges to ORION, payment of OUT -OF-WARRANTY shipping charges, or damage to other property caused by any defects in this product.
Amplifier Section XTREME 200 XTREME 400.4 Power output 4 Ω stereo (watts) 1 50 x 2 50 x 4 50 x 2, 200 x 1 Power output 2 Ω stereo (watts) 2 100 x 2 100 x 4 Power output 4 Ω mono (watts) 1 200 x 1 200 x 2 Distortion all channels driven <0.1% THD <0.
1 All channels driven, continuous rated 4 Ω load, 20Hz to 20,000Hz, >0.1% THD, per input voltage at 12.0VDC. 2 All channels driven, continuous rated 2 Ω load, 20Hz to 20,000Hz, >0.1% THD, per input voltage at 12.0VDC. 3 XTREME amplifers are designed to accept full 9 V olts RMS input when set to the minimum gain position.
TECHNICAL DESIGN FEA TURES page 8 PRS Power Supply Complementary Matched Bipolar Outputs 16 Gauge Speaker and Remote A TC Fuse Crossover Frequency Control Stereo/SUM/MONO Switch Gain Control RCA Input.
1. Power LED - when lit indicates that the amplifier is on 2. Front Output Configuration Switch - determines the output configuration of the amplifier 3. Front Gain Control - continuously adjusts from 200mV to 5V rms for full power output 4. 2-Channel / 4-Channel Switch - configures the amplifier for two or four RCA inputs 5.
SYSTEM PLANNING SYSTEM 1 The easiest way to maximize the performance for your ORION XTREME amplifier is to properly plan your sys- tem. By planning your system, you can avoid situation where the performance of the reliability of your system is compromised.
SYSTEM PLANNING SYSTEM 2 page 11 + – + – + – + – – + + – + – System 2 adds a subwoofer to system 1. Amplifier 1 is configured high-pas for the satellite speakers and Amplifier 2 is configured low-pass for a single 4 Ω sub- woofer .
SYSTEM PLANNING SYSTEM 3 page 12 + – + – + – + – – + + – + – + –.
System 3 uses a 4-channel amplifier to drive an entire system. The front channels are configured high-pass operation for satellites. Th e rear channels are configured low-pass for two dual voice coil subwoofers.
page 14 + – + – + – + – – + + – + – + – + – + – + – – + + – SYSTEM PLANNING SYSTEM 4.
SYSTEM PLANNING SYSTEM 4 System 4 uses a 4-channel amplifier to power the front satellites and a single 4 Ω subwoofer and a 2-channel amplifier for the rear satellites.
page 16 + – – + + – + – + – + – + – – + + – + – + – + – + – SYSTEM PLANNING SYSTEM 5.
SYSTEM PLANNING SYSTEM 5 System 5 uses two 4-channel amplifiers for the front and rear satellites and two 2-channel amplifiers for two subwoofers. This system is designed to really rock.
INST ALLA TION The installation of all ORION components will determine the overall performance result. Improper installation will not only limit the performance of your ORION system but also potentially compromise the reliability of this amplifier .
page 19 POWER CONNECTIONS • Minimum 8 gauge power and ground cable is recommended for acceptable performance • Fuse power wire less than 18” from battery • Ground amplifier to a good chassis g.
SPEAKER CONNECTIONS 2-CHANNEL STEREO CONFIGURA TION • Lowest recommended impedance is 2 Ω stereo • Output can be configured for high-pass, low-pass or full range operation • Output can be configured for either stereo operation or summed for subwoofer applications.
SPEAKER CONNECTIONS SINGLE BRIDGED CONFIGURA TION • Lowest recommended impedance is 4 Ω bridged mono • Output can be configured for high-pass, low-pass or full range operation • Output can be .
SPEAKER CONNECTIONS TRI-MODE 3-CHANNEL CONFIGURA TION • Lowest recommended impedance is 2 Ω stereo and 4 Ω bridged mono • Output must be set for full range operation • Output must be configured for stereo operation • Passive crossover frequencies must not overlap.
SPEAKER CONNECTIONS 4-CHANNEL STEREO CONFIGURA TION • Front and rear channel lowest recommended impedance is 2 Ω stereo • Crossover , output and gain configurations are independently adjustable between the front and rear channels • 2-channel or 4-channel input can be used for this configuration.
SPEAKER CONNECTIONS 3-CHANNEL STEREO/BRIDGED CONFIGURA TION • Front channels are configured for 2-channel stereo operation • Front channel lowest recommended impedance is 2 Ω stereo • Rear cha.
SPEAKER CONNECTIONS TWO-CHANNEL BRIDGED CONFIGURA TION • Front and rear channels are configured for bridged 2- channel operation • Lowest recommended impedance for both front and rear channels is .
SPEAKER CONNECTIONS TRI-MODE 6-CHANNEL CONFIGURA TION • Lowest recommended impedance is 2 Ω stereo and 4 Ω bridged mono • Front and rear outputs must be set for full range operation • Front and rear outputs must be configured for stereo operation • Passive crossover frequencies must not overlap.
OUTPUT CONFIGURA TIONS Three position switches determine output configuration for the XTREME amplifiers. Each stereo pair of channels can be configure d in either stereo, summed-bridged and bridged-mono. The switch or switches are located on he outermost edge of the amplifier .
4-CHANNEL AMPLIFIER INPUT CONFIGURA TIONS The 2-channel input / 4-channel input switch routes RCA input from the front RCA inputs to the rear section of the amplifier . T his allows the XTREME 4-channel amplifier to utilize a single set of RCAs to feed signal to both the front and rear channels of the amplifier .
FINE TUNING THE CROSSOVER The crossover section is marked at four frequency points for ease of system adjustment. These points are 45Hz, 175Hz, 600Hz and 5,000Hz. Specific crossover points can be chosen based on the recom- mended operational bandwidth of your speakers.
CHOOSING MOUNTING LOCA TIONS The location of your XTREMEamplifier will depend on several important issues. Due to the low profile size of the XTREME amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
GENERAL PRECAUTIONS AND INST ALLA TION TIPS Caution: Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle. Disconnect the vehicle’ s ground wire at the battery before making or breaking connections to the audio system’ s power supply te r minals.
STEP BY STEP INST ALLA TION Step 1 Determine the location for the amplifier . Refer to the Mounting Locations section in this manual for detailed infor matio n. Step 2 Decide on the system configuration for your amplifier . For system suggestions, refer to the System Planning section of t his manual.
After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your ORION XTREME system. Step 1 Check all the wiring connections to be sure they are correct and secure.
ADJUSTING THE SOUND OF THE SYSTEM page 34 Once you have checked the system’ s operation, adjust the sound of the system. Adjusting the sound of the system is accomplish ed by setting the level controls and adjusting the internal crossovers. Step 1 T urn the signal source volume control down all the way .
page 35.
SYMPTOM PROBABLE CAUSE ACTION TO T AKE No output Low or no remote turn-on input Check remote turn-on voltage output at amplifier and fix as needed. Fuse blown Check power wire integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and fix or replace as needed.
Distorted output Internal crossover not set properly Readjust crossovers. Refer to the Internal Crossover section of this for speakers manual for detailed instructions. Speakers are blown Check system with know working speakers and fix or replace as needed.
AUTOSOUND 2000 TROUBLESHOOTING TIPS QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMS Preface: All audio systems exhibit noise; however , if the level of noise is low enough, and the signal level high enough, noise should not be a problem.
page 39 II . DECK TO AMP . Using a new set of signal cables, connect one channel from the output of the deck directly into one channel of your clean amp.
page 40 probable that the component has inadequate isolation. Solutions include, changing components or permanently adding an external isolated power supply (Call Autosound 2000 at 209-465-3450 for info on isolated power supplies). SUMMA TION During the design stage of your vehicles, try to avoid using extra batteries and high output alternators.
The more components installed on a signal path, the more chances for noise to enter a system. The more electrical accessories on a car , the more noise will be produced by the alternator . This information was compiled from more than 20 years of working in car audio.
H IGH P ERFORMANCE C AR A UDIO A MPLIFIERS , S IGNAL P ROCESSORS AND L OUDSPEAKERS ©1998 Orion Industries, Incorporated 9235 S. McKemy St., T empe, Arizona 85284 Phone: 602.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Orion Car Audio 200 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Orion Car Audio 200 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Orion Car Audio 200 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Orion Car Audio 200 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Orion Car Audio 200, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Orion Car Audio 200.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Orion Car Audio 200. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Orion Car Audio 200 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
