Manuale d’uso / di manutenzione del prodotto BAR608HGA del fabbricante Oregon Scientific
Vai alla pagina of 18
W ireless W eather Station Model : BAR608HGA User Manual BAR608HGA lab test cover R 2 1/8/04, 6:38 PM 1.
EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .
EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless W eather Station (BAR608HGA). This device bundles precise time keeping, weather forecast, barometric trend with altitude adjustment, and indoor and outdoor temperature and humidity monitoring features into a single tool you can use from the convenience of your home.
EN 3 PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT button 2. Weather Forecast & Barometric T rend Area 3. Outdoor T emperature & Humidity Area 4. Indoor T emperature & Humidity Area 5. Clock / Alarm Area 6 Moon Phase 7. and : increase or decrease setting / activate or deactivate Atomic Clock.
EN 4 BACK VIEW 1. W all mount 2. Battery compartment 3. T able stand REMOTE SENSOR (THGR122N) GETTING ST ARTED 1 2 3 BAR608HGA lab test R2 1/17/04, 4:39 PM 4.
EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1. Wall mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) 1 2 1 2 3 4 BAR.
EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. T ABLE ST AND OR W ALL MOUNT Use the stand on the back of the product, or mount it on a wall with a nail.
EN 7 3. Set the channel. The switch is located in the battery compartment. 4. Place the sensor near the main unit. Press RESET on the sensor . Then, press and hold MEM and CHANNEL on the main unit to initiate signal sending between the sensor and the main unit.
EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure.
EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold DOWN for 2 seconds. Then, manually set the clock following the "Set Clock" instructions (below).
EN 10 If no button is pressed, the Alarm will automatically silence after 2 minutes. It will then sound again after 8 minutes. BAROMETER This product tracks barometric pressure changes over the past 24 hours to provide the weather forecast ( 13) and a trend line showing the direction of barometric change.
EN 11 NOTE TEMPERA TURE AND HUMIDITY This product can display current, minimum, and maximum temperatures and humidity percentage information collected by the remote sensors and main (indoor) unit. Outdoor data is collected and displayed every 40 seconds.
EN 12 When you press RESET , all settings will return to default value, and you will lose all stored information. SAFETY AND CARE Clean the product with a slightly damp cloth and alcohol- free, mild detergent. Avoid dropping the product or placing it in a high-traffic location.
EN 13 SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 142 x 63 x 158 mm (5.5 x 2.5 x 6.2 inches) W eight 366 g (12.96 ounces) with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.
EN 14 RELA TIVE HUMIDITY Range 25% to 95% Resolution 1% Memory Minimum / maximum BAROMETER Unit mb/hPa or inHg Range 700 to 1050 mb (20.67 to 30.01 inHg) Resolution 1 mb (0.
EN 15 FCC ST A TEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
EN 16 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead.
© 2004 Oregon Scientific. All rights reserved. P/N.: 086-003312-012 BAR608HGA lab test back cover 12/29/03, 10:40 PM 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Oregon Scientific BAR608HGA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Oregon Scientific BAR608HGA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Oregon Scientific BAR608HGA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Oregon Scientific BAR608HGA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Oregon Scientific BAR608HGA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Oregon Scientific BAR608HGA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Oregon Scientific BAR608HGA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Oregon Scientific BAR608HGA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
