Manuale d’uso / di manutenzione del prodotto RMC-25key del fabbricante Optoma Technology
Vai alla pagina of 58
1 English T able of Contents ................................................................................... 1 Usage Notice .......................................................................................... 2 Safety Information ...........
2 English Usage Notice Safety Informations The lightning ash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suf cient magni- tude to constitute a risk of electric shock to persons.
3 English Usage Notice When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages 48-49.
4 English Usage Notice Do: Turn off the product before cleaning. Use a soft cloth moistened with a mild detergent to clean the display housing. Disconnect the power plug from the AC outlet if the product is not being used for a long period of time.
5 English Usage Notice Eye Safety Warnings ▀ ■ Avoid staring directly into the projector’s beam of light at all times. ▀ ■ Minimize standing facing into the beam. Keep your back to the beam as much as possible. ▀ ■ Using a stick is recommended to avoid the need for the pre- senter to enter the beam.
6 English Introduction Product Features This product is a Short throw XGA single chip 0.55” DLP ® projector. Outstanding features include: True XGA, 1024 x 768 addressable pixels Texas Inst.
7 English Introduction Power Cord 1.8m IR Remote Control Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete.
8 English Introduction VGA-Out VGA-In/S CART DVH S-Video Video RS-232 USB RJ-45 Audio-In Audio-L Audio- 1. IR Receivers 2. Control Panel 3. Focus 4. Projection Lens Main Unit Product Overview 5.
9 English Introduction Control Panel 1. On/Standby and Power LED 2. Lamp LED 3. Temp LED 4. Menu 5. Source 6. Re-Sync 7. Enter 8. IR Receiver 9. Four Directional Select Keys 10.
10 English Introduction Connection Ports 1. VGA-Out Connector (Monitor Loop-through Output) 2. VGA-In/SCART Connector (PC Analog Signal/Component Video Input/HDTV/SCART) 3. DVI-I Connector (PC Digital (HDCP)/PC Analog/Component Video Input) 4. S-Video Input Connector 5.
1 1 English 1. Button LED 2. Power On/Off 3. Page Up 4. Mouse Right Click 5. Four Directional Select Keys 6. Re-Sync 7. Page Down 8. Volume +/- 9. Zoom 10. AV mute 11. Video Source 12. VGA Source 13. Freeze 14. S-Video Source 15. DVI Source 16. Brightness 17.
12 English Installation Connecting the Projector Due to the difference in applications for each country, some regions may have different accessories. Connect to Computer/Notebook 1................................................................
13 English Installation Connect to Video Sources 1............................................................................................................... Power Cord 2...................................................Composite Video Cable (Optional accessories) 3 .
14 English Installation Powering On/Off the Projector Turn on the projector rst and then select the signal sources. Lens Cap 1 ON/STANDBY Power LED 2 Powering On the Projector 1. Remove th e lens cap. 2. Ensure that the power cord and signal cable are securely connected.
15 English Installation Warning Indicator When the “LAMP” indicator lights red, the projector will automatically shut itself down. Please contact your local reseller or service center. See pages 55-56. When the “TEMP” indicator lights red, it indicates the projector has overheated.
16 English Installation Adjusting the Projected Image Adjusting the Projector’s Height The projector is equipped with elevator feet for adjusting the image height. To raise the image: 1. Locate the adjustable foot you wish to modify on the underside of the projector.
17 English Installation Adjusting the Projector’s Focus Adjusting Projection Image Size To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 1.6 to 12.1 feet (0.5 to 3.7 meters). Hd 82.0" (208.
18 English User Controls Control Panel & Remote Control There are two ways for you to control the functions: Control Panel and Remote Control. Using the Control Panel ON/STANDBY Power LED Refer to the “Power On/Off the Projector” section on pages 14-15.
19 English User Controls Using the Remote Control Power Refer to the “Power On/Off the Projector” section on pages 14-15. PC/Mouse control The PC/Mouse control can be used to con- trol mouse movement. The mouse function is enabled using the USB cable to connect your computer and the projector.
20 English User Controls Video RS-232 USB RJ-45 Audio-Out Audio-In Video RS-232 USB RJ-45 Audio-Out Audio-In USB cable to USB port to USB port When the projector is connected to PC via the USB cable, the remote will work as a mouse for control. Using the Remote Control DVI Press “DVI” to choose DVI-I source.
21 English User Controls The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad.
22 English User Controls Menu Tree (*) “Signal” menu is only supported in Analog VGA (RGB) signal. *.
23 English User Controls Image Display Mode There are many factory presets optimized for various types of images. Presentation: Good color and brightness from PC input. Bright: Maximum brightness from PC input. Movie: For home theater . sRGB: Standardised accurate color.
24 English User Controls Color Select the Red/Green/Blue Gain for brightness adjustments and Bias for contrast adjustments for the whole picture. Individual color adjustments for Cyan, Magenta, Yellow can also be adjusted. Reset Choose “Yes” to return the factory default settings for color adjustments.
25 English User Controls Image | Advanced Degamma This allows you to choose a degamma table that has been ne-tuned to bring out the best image quality for the input. Film: for home theater. Video: for video or TV source. Graphics: for image source.
26 English User Controls Image | Advanced Input Source Enable input sources. Press “ ” into the next menu as below and then use or to select. Press “Enter” to nalize the selection. The projector will not search inputs that are de-selected.
27 English User Controls Display Format Use this function to choose your desired aspect ratio. 4:3: This format is for 4x3 input sources not enhanced for Wide screen TV. 16:9 I: This format is for 16x9 input sources, like HDTV and DVD enhanced for Wide screen TV.
28 English User Controls window format LBX format 16 : 9-I format or or 16 : 9-II format 4 : 3 format Input Signal Display area Picture area Display on Screen.
29 English User Controls Overscan Overscan function removes the noise in a video image. Overscan the ima ge to remo ve vide o enco ding no ise on the ed ge of vid eo source. Zoom Press the to reduce the size of an image. Press the to magnify an image on the projection screen.
30 English User Controls Language Choose the multilingual OSD menu. Press or into the sub menu and then use the or key to select your preferred language.
31 English User Controls Setup Projection Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the im age so you can project behind a translucent screen. Front-Ceiling When you select this function, the projector turns the image upside down for ceiling-mounted projection.
32 English User Controls Setup Projector ID Allow the RS232 control of an individual projector. Range 00-99. Mute Choose the “On” to turn mute on. Choose the “Off” to turn mute off. Volume Press the to decrease the volume. Press the to increase the volume.
33 English User Controls Setup | Security Security Settings On: Choose “On” to use security verication when the turning on the projector. Off: Choose “Off” to be able to switch on the projector without password verication.
34 English User Controls Setup | Security ■ First Time: 1. T h ePasswo rdis4di g its,DEF AULTV ALU Eis“12 3 4” .( rsttime) 2. U senumberbuttonso nthere motetos electyourpass word,andth e n press “Enter ” ke ytoco n rmyo urselect ion.
35 English User Controls Setup | Signal Phase Synchronize the signal timing of the display with the graphic card. If you experience an unstable or ickering image, use this function to correct it. Frequency Change the display data frequency to match the frequency of your computer’s graphic card.
36 English User Controls Setup | Advanced Logo Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open. Optoma: The default startup screen of Optoma projector.
37 English User Controls Setup | Network Network State To display network information. DHCP Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open.
38 English User Controls 1. Fill in a new IP, a subnet mask, a gateway and a DNS in the dialogue box. 2. Then choose apply and press “ ” button to effectuate the con guration process. 3. Open your web browser and type in from the OSD LAN screen then the web page will display as below: 4.
39 English User Controls Step 3: To open Network Connections, click Start , click Control Panel , click Network and Internet Connections , and then click Network Connections . Click the connection you want to con gure, and then, under Network Tasks , click Change settings of this connection .
40 English User Controls Source Lock On: The projector will search specied connection port. Off: The projector will search for other signals if the current input signal is lost.
41 English User Controls Opti ons | A dvan ced Direct Power On Choose “On” to turn on Direct Power On mode. The projector will automatically power on when AC power is supplied, without pressing the “ON/STANDBY” key on the projector control panel or “ Power ” key on the remote control.
42 English User Controls Options | Lamp Settings Lamp Hours Display the projection time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp.
43 English Appendices Image Problems No image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure all the pins of connectors are not bent or broken.
44 English Appendices 6. Select the “Change” button under the “Monitor” tab. 7. Click on “Show all devices”. Next, select “Standard monitor types” under the SP box; choose the resolution mode you need under the “Models” box.
45 English Appendices Image has vertical ickering bar Use “Frequency” to make an adjustment. See page 35 for more information. Check and recongure the display mode of your graphic card to make it compatible with the projector. Image is out of focus Make sure the lens cap is removed.
46 English Appendices Intermission Problems The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power. Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound.
47 English Appendices Message Reminders Fan failed: Temperature warning: Lamp Warning: Source Message: Remote Control Problems If the remote control does not work Check the operating angle for the remote control is approximately ±22.
48 English Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible.
49 English Appendices 5 1 2 3 4 Lamp Replacement Procedure: 1. Switch off the power to the projector by pressing the “Power” button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Use a screwdriver to unscrew the 2 screws from the cover.
50 English Appendices Compatibility Modes Mode Resolution V-Sync (Hz) Analog Digital VGA 640 x 350 70, 85 70, 85 VGA 640 x 400 85 85 VGA 640 x 480 60, 72, 75, 85 60, 72, 75, 85 VGA 720 x 400 70, 85 70.
51 English Appendices RS232 Commands Pin no. Spec. 1 N/A 2 RXD 3 TXD 4 N/A 5 GND 6 N/A 7 N/A 8 N/A 9 N/A 1 2 3 4 5 6 7 8 9 RS232 Pin Assignments Pin no.
52 English Appendices RS232 Protocol Function List RS232 Commands Baud Rate : 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Project.
53 English Appendices SEND to projector ----------------------------------- -------------------------- --------------------------- ----------------------------- ----------------------------- ---------.
54 English Appendices Please note that damage result- ing from incorrect installation will invalidate the warranty. Ceiling Mount Installation 1. To prevent damaging your projector, please use the Optoma’s recommended mount package for installation.
55 English Appendices Optoma Global Ofces Forserviceorsupportpleasecontactyourlocalofce. USA 715 Sycamore Drive Tel : 408-383-3700 Milpitas, CA 95035, USA Fax : 408-383-3702 www.optomausa.com Service : services@optoma.com Canada 5630 Kennedy Road, Mississauga, ON, L4Z 2A9, Canada Tel : 905-361-2582 www.
56 English Appendices Korean WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, Tel : +82+2+34430004 seoul,135-815, KOREA Fax : +82+2+34430005 Japanese 東京都足立区綾瀬3-25-18 株式会社オーエスエム E-mail : info@osscreen.com サポートセンター: 0120-46-5040 www.
57 English Appendices Regulation & Safety notices Thisappendixliststhegeneralnoticesofyourprojector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules.
58 English Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2 . This device must accept any interference received, including interference that may cause undesired operation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Optoma Technology RMC-25key è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Optoma Technology RMC-25key - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Optoma Technology RMC-25key imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Optoma Technology RMC-25key ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Optoma Technology RMC-25key, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Optoma Technology RMC-25key.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Optoma Technology RMC-25key. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Optoma Technology RMC-25key insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
