Manuale d’uso / di manutenzione del prodotto Lift 42 del fabbricante Omnimount
Vai alla pagina of 20
Lift 42 Motorized Flat Pane l Lift System with Universal Adapter. IMAGES MAY DIFFER FROM ACTUAL PRODUCT. INSTRUCTION MANUAL Lift 42 = L1-10235-PRO -101008vE PN # 10235 ULN #.
2 W ARNING – ENGLISH WARNING! SEVE RE PE RS ONAL INJ URY AND PROPERT Y DAMAG E CAN RESULT FROM IMPROPER INSTALLA TION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING. If you do not understand the in structions o r have any concerns or ques tions, please contact a qualified instal ler.
3 Contents Power cable 1 14 Motor cable 1 13 Screen Adapter 1 12 Vertical Exten sion Rails an d covers 2 11 Universal Adapter 1 10 Corner brackets 2 9 IR Receiver/Control switch 1 8 Remote Contr ol 1 .
4 Contents Monitor Kit: Parts M-A through M- N are used to connect the TV to the universa l adapter. Spacers ma y be necessary for a p roper fit with recessed m ounting holes or to allow access to TV inputs.
5 PINCH POINT WARNING! • Improper construction o f lift enclosure can create dangerous pinch points . It is the responsibility of the installer to ensur e the intended use of this product does not create hazardous pinch zones.
6 Before Enclosure Con struction! Assemble lift mechanis m and connect the TV to be used in the install to determine dime nsions for the lift enclosure prior to construction. Be sure to le ave room for adjustments If necessary. An out of cabinet assembly of t he mechanism can be done using steps 1,4, 6,8,9 and 10 in order.
7 Measurements Required For Cabin etry Dimensions Use previous page to find the minimum INTERIOR di mensions for custom enclosures. Height Width Depth.
8 Step 1 O 1 2 x4 Attach the Base B racket (1) to the Lift Column (2): • Using the sm all Hex wrench and 6mm x 20mm screws (O), connect the base bracket to the lift column. Note that one side is counter sunk to ensure flush installation of screws.
9 Step 2 Q 3 Attach the Bayonet Bra cket (3) to the enclosure: • Using the #10 x ¾” sc rews (Q), attach t he bracket so that the top edge of the brackets back plate is 20” above the botto m mounting surface ( the bottom of the cabinet or top of the spacer b lock if used).
10 Step 3 Figure A Figure B 3 2 Secure Lift Column and Base Bracket in enclosure: • Gently glide the lift co lumn into place on the bayonet bracke t so that the tapered slots on the co lumn are secured to the extrusions on the bracket. Gently push down until the base bracket is touching the bottom of the enc losure.
11 Step 4 x4 4 4 12 12 TOP S Connect Sc reen Adap ter (12) to the Screen Support (4 ): • Use the la rge hex wrench to secure the screen adapter to the screen support using four 3/8-16 x ¾” screws (S) . Depending on TV size and mounting hole pattern the screen adapter can be vertically ad justed for optimal fit.
12 Initialize the lift system: • Connect the motor cable to the control box and “pigtail” on the lift column as shown in figures A and B. • Connect the IR receiver/control switch and c ontrol box power as shown in figures C and D.
13 Attach the Screen Support(4 ) and Top Plate(5) to the Lift Column(2): • Before attaching the top plate ensure t hat the rubber guide on the “pigtail” is secured in the square cut o ut on what will be the front of the lift col u mn (fig. A).
14 Step 7 2 1 Q x4 Attach lif t assembl y to enclosu re base: • Using a level on the top p late ensure that the lift co lumn and assembly are level w ithin the enclosu re. Gently tap the base of the colu mn left or right to bring the top plate le vel.
15 Step 8 11 M-A – M-L M-A – M-L 10 10 Note : IF MONITOR SCREWS “BOTTOM OUT” , THEN USE ADDITI ONA L WASHERS (not included) TO TAKE UP THE SLACK. TV Attach the Universal Adapter to the TV: • Place the TV fa ce down on a protected su rface.
16 Step 9 Figure B Figure A Figure C Connect the TV and universal adapter to the lift column: • Partially in stall two ¼-20 x ½” (W) hex screws into t he top r ear of th e universal adapter (fig . A). • Lift and lock T V into position on sc reen adapter (fig .
17 Step 10 Install universa l adapter rail covers : • Carefully at tach the correct pla stic cove rs to the univer sal adapter..
18 Appendix Using guide pins for a floating top: • The guide pins are recommended for use as a safety measure to pre vent pinch points. A te mplate has been inc luded to assist with guide pin use. • If the guide pins are to be used, make su re the top surf ace of the en cl osure will not be used as a load bearing surface.
19 Guide Pin/Top Plate Template.
20 OmniMount Systems , Inc . 8201 South 48th Street Phoenix, AZ 85044-5355 1-800-MOU NT-IT 1-800-668-6848 www.omnim ountpro.com Thank you for purchasing an OmniMount product.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Omnimount Lift 42 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Omnimount Lift 42 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Omnimount Lift 42 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Omnimount Lift 42 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Omnimount Lift 42, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Omnimount Lift 42.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Omnimount Lift 42. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Omnimount Lift 42 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
