Manuale d’uso / di manutenzione del prodotto BNC-08DI del fabbricante Omega Engineering
Vai alla pagina of 25
www .omega.com e-mail: info@omega.com U ser ’ s Guide BNC-08DI, BNC-16DI AND BNC-16SE T erminal Boards Shop online at.
W ARRANTY / DISCLAIMER OME GA ENGINEERING, INC. war rants this unit to be free of defects in materials and workmanship for a period of 1 3 months from date of purc hase. OM E GA ’ s W ARRAN TY adds an additional one (1) month grace period to the normal one (1) year pr oduct warranty to cover handling and shipping time.
19 BOARD ACCESSIBILITY ........................................................... 15 INPUT CONFIGURATIONS ......................................................... 14 BOARD COMPATIBILITY .......................................................... 12 P1 CONNECTOR MAP .
INTRODUCTION The BNC series of signal con nection boxes have been desig ned as univ ersal interfaces f or the DAS fam ily of analog I/O boards. T he BNC-08DI accepts u p to 8 differential pairs of analog inpu ts w hile the BNC- 16SE and the BNC- 16DI can accept up to 64 sing le end ed or 3 2 differ ential analo g inputs.
BNC-08DI The BNC-08D I incorporates 16 f ront panel m ounted BNC con nectors prov iding up to 8 dif feren tial analog i nputs to the C IO-DA S family of data acquisition boards. B1-B16 The 16 front panel mounted BNC connectors B1-B16, are routed through the enclosure to the rear panel-mounted 37 D connector P2.
EXTERNAL TRIGGER The EXTERNAL TRIGGER BNC con nectors B17 and B18 are provided for application s that requ ire external digital triggering of t he data acquisition board. These connectors could also be used in applications requiring synchronization to the digital trigger si gnal.
BNC-16DI The BNC-16 DI incorpor ates 16 front panel mounted BNC’s allowing connection of up to 8 d ifferential analog inputs to the CIO-DAS and PCI family of data acquisition board s.
. . P1 The front panel m ounted DB37 connector P1 provides a variety of I/O sig nals, n ot including the 16 analog input signals from BNC’s B1-B16. P lease refer to the P1 CONNECTOR MAP section for a detailed explanation of P1’s connection schem e and signal availability.
EXTERNAL TRIGGER The EXTERNAL TRIGGER BNC con nectors B17 and B18 are provided for application s that requ ire external digital triggering of t he data acquisition board. These connectors could also be used in applications requiring synchronization to the digital trigger si gnal.
Headers P6 and P7 are factory set to the “1-2” position, pre-config uring B15 and B16 as analog input BNC’s. For those applicati ons w hich require D/A outputs along with B15 and B16 to be used in the an alog input m ode; the user can leave B15 and B16 in the an a log input mode and access the D/A outputs at connector P1.
BNC-16SE The BNC-16S E incorporates 16 front panel mou nted BNC’s allow ing connect ion of u p to 16 singl e-ended an alog inpu ts to th e CIO-DAS an d PCI family of data acquisition boards.
. P1 The front panel m ounted DB37 connector P1 provides a variety of I/O sig nals, n ot including the 16 analog input signals from BNC’s B1-B16. P lease refer to the P1 CONNECTOR MAP section for a detailed explanation of P1’s connection schem e and signal availability.
EXTERNAL TRIGGER The EXTERNAL TRIGGER BNC con nectors B17 and B18 are provided for application s that requ ire external digital triggering of t he data acquisition board. These connectors could also be used in applications requiring synchronization to the digital trigger si gnal.
Headers P6 and P7 are factory set to the “1-2” position, pre-config uring B15 and B16 as analog input BNC’s. For those applicati ons w hich require D/A outputs along with B15 and B16 to be used in the an alog input m ode; the user can leave B15 and B16 in the an a log input mode and access the D/A outputs at connector P1.
P1 CONNECTOR MAP Connector P1 prov ides the u ser w ith a variety of I/O sign als, not including th e 16 analog input signals from B1-B16. T he following diagram illustrates the connection schem e used to route these signals among connectors P2, P3 and P4 to connector P1.
3&RQQHFWRU0DSIRU%1&', 13.
BOARD COMPATIBILITY The BNC-08DI is compatible with the following DAS boards: 8 Differential Inputs CIO-DAS08-PGM 8 Differential Inputs CIO-DAS08-PGL 8 Differential Inputs CIO-DAS08-PGH 8 Differential.
INPUT CONFIGURATIONS Each BNC connector of the BNC-08/16 DI and the BNC-16SE incorpo rates pro gramm ab le, signal conditioning circuitry, wh ich allows the user to connect a wide variety of options including filtering, bypassing, voltage division and termination.
open resistor open open open open RXF open open open 0 ohm 0 ohm open RXE capacitor open open capacitor resistor open RXD 0 ohm open open resistor resistor open RXC 0 ohm 0 ohm 0 ohm 0 ohm 0 ohm 0 ohm.
The following diagram illustrates the signal conditioning circuitry of a differential analog input channels used on the BNC-16D I and the BNC-08DI. resistor resistor resistor resistor resistor resisto.
The following illustrations describe some comm on differential mode connection meth ods o f the BNC-08/16DI enclosure. T hese are just a few of the many possible connection methods made possible using the programmable signal conditioning circuits. 1. Diagram A .
BOARD ACCESSIBILITY Accessi ng the in dividual BNC input con figu ration circuits, or headers P6 or P7 (B NC-16SE, BNC16DI on ly) can be easily accomplished by removing the following hardware: enclosure screws (2), External Trigger nut and washer, and P2 set screws (2).
EC Declaration of Conformity We, ComputerBoards, Inc., declare under sole responsibility that the product: Description Part Number BNC Boxes BNC 08/16DI BNC 16SE to which this declaration relates, mee.
Servicing Nor th America: USA: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.
Where Do I Find Ever ything I Need for Pr ocess Measurement and Control? OM EGA…Of Course! Shop online at www .omega.com TEMPERA TURE Thermocouple, RTD & Thermistor Probes, Connectors, P.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Omega Engineering BNC-08DI è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Omega Engineering BNC-08DI - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Omega Engineering BNC-08DI imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Omega Engineering BNC-08DI ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Omega Engineering BNC-08DI, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Omega Engineering BNC-08DI.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Omega Engineering BNC-08DI. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Omega Engineering BNC-08DI insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
