Manuale d’uso / di manutenzione del prodotto asus pc del fabbricante Asus
Vai alla pagina of 90
V-Series M2V890 ASUS PC (Desktop Barebone).
i i Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a r.
iii Table of contents Notices ................................................................................................ vi Safety information ..............................................................................vii About this guide ...
i v Table of contents Chapter 3: Starting up 3.1 Installing an operating system .............................................. 3-2 3.2 Powering up .......................................................................... 3-2 3.3 Support CD information .
v Table of contents 5.3 Main menu ........................................................................... 5-12 5.3.1 System Time ........................................................ 5-12 5.3.2 System Date ......................................
v i Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide Audience This guide provides general information and installation instructions about the ASUS V-Series M2V890 barebone system. This guide is intended for experienced users and integrators with hardware knowledge of personal computers.
i x Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task.
x System package contents Check your ASUS V-Series M2V890 barebone system package for the following items. If any of the items is damaged or missing, contact your retailer immediately. Item description 1. ASUS V-Series M2V890 barebone system with • ASUS motherboard • 250 W PFC power supply unit • ASUS chassis 2.
Chapter 1 System introduction This chapter gives a general description of the ASUS V-Series M2V890 Barebone System. The chapter lists the system features including introduction on the front and rear panel, and internal components.
1-2 Chapter 1: System introduction 1.1 Welcome! Thank you for choosing the ASUS V-Series M2V890! The ASUS V-Series M2V890 is an all-in-one barebone system with a versatile home entertainment feature.
1-3 ASUS V-Series M2V890 1. 5.25-inch drive bay covers. These bays are for IDE optical drives. 2. 3.5-inch drive bay covers. These slots are for 3.5-inch oppy or hard disk drives. 3. Headphone port. This Line In (green) port connects a headphone with a stereo mini-plug.
1-4 Chapter 1: System introduction 1.3 Rear panel The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices. 1. Voltage selector. This switch allows you to adjust the system input voltage according to the voltage supply in your area.
1-5 ASUS V-Series M2V890 5. COM port. This 15-pin port is for a VGA monitor or other VGA- compatible devices. 6. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 7. Video Graphics Adapter (VGA) port. This port is for a VGA monitor or other VGA-compatible devices.
1-6 Chapter 1: System introduction Voltage selector The system’s power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area.
1-7 ASUS V-Series M2V890 1.4 Internal components The illustration below is the internal view of the system when you remove the top cover and the power supply unit. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing additional system components.
1-8 Chapter 1: System introduction.
Chapter 2 Basic installation This chapter provides step-by-step instructions on how to install components in the system..
2-2 Chapter 2: Basic installation 2.1 Preparation Before you proceed, make sure that you have all the components you plan to install in the system. Basic components to install 1. Central Processing Unit (CPU) 2. DDR2 Dual Inline Memory Module (DIMM) 3.
2-3 ASUS V-Series M2V890 2.3 Removing the side cover and front panel assembly 1. Remove the cover screws on the rear panel. 2. Pull the side cover toward the rear panel until its hooks disengage from the chassis tab holes. Set the side cover aside. 3.
2-4 Chapter 2: Basic installation 2.4 Central Processing Unit (CPU) 2.4.1 Overview The motherboard comes with a 940-pin AM2 socket designed for the AMD Athlon™ 64 X2/AMD Athlon™ 64/AMD Sempron™ processor. 2.4.2 Installing CPU To install a CPU: 1.
2-5 ASUS V-Series M2V890 3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it ts in place. The CPU ts only in one correct orientation.
2-6 Chapter 2: Basic installation 2.4.3 Installing the heatsink and fan The AMD Athlon™ 64 X2/AMD Athlon™ 64/AMD Sempron™ processor require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan.
2-7 ASUS V-Series M2V890 2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retent ion bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place.
2-8 Chapter 2: Basic installation 2.5 Installing a DIMM The system motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Module (DIMM) sockets. The following gure illustrates the location of the sockets: 2.5.1 Memory configurations You may install 256 MB, 512 MB, and 1 GB unbuffered ECC/non-ECC DDR2 DIMMs into the DIMM sockets.
2-9 ASUS V-Series M2V890 Qualified Vendors Lists (QVL) DIMM support Side(s): SS - Single-sided DS - Double-sided Visit the ASUS website for the latest DDR2-667/533 MHz QVL.
2-10 Chapter 2: Basic installation 2.5.3 Removing a DDR2 DIMM Follow these steps to remove a DIMM. 1. Simultaneously press the retaining clips outward to unlock the DIMM. 2. Remove the DIMM from the socket. Support the DIMM lightly with your ngers when pressing the retaining clips.
2-11 ASUS V-Series M2V890 2.6 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 2.6.1 Installing an expansion card To install an expansion card: 1.
2-12 Chapter 2: Basic installation * These IRQs are usually available for ISA or PCI devices. When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments. Otherwise, conicts will arise between the two PCI groups, making the system unstable and the card inoperable.
2-13 ASUS V-Series M2V890 2.6.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specications.
2-14 Chapter 2: Basic installation 2.7 Installing an optical drive Refer to the instructions in this section if you wish to install a new optical drive. Follow these steps to install an optical drive: 1. Place the chassis upright. 2. Remove the drive slot metal plate cover.
2-15 ASUS V-Series M2V890 2.8 Installing a hard disk drive The system may have one pre-installed 3.5-inch Serial ATA or IDE hard disk drive. Refer to this section to install additional Serial ATA or IDE hard disk drive(s). To install a Serial ATA hard disk drive: 4.
2-16 Chapter 2: Basic installation If your Serial ATA HDD has both 4-pin and 15-pin connectors at the back, use either the 15-pin SATA power adapter plug OR the legacy 4-pin power connector. DO NOT use both to prevent damage to components and to keep the system from becoming unstable.
2-17 ASUS V-Series M2V890 To install an IDE hard disk drive: 1. Follow steps 1-4 of the previous section. 2. Connect the blue interface of the IDE ribbon cable to the primary IDE connector (blue connector labeled PRI_IDE) on the motherboard. See page 4-6 for the location of the connector.
2-18 Chapter 2: Basic installation 2.9 Installingaoppydiskdrive The V-Series M2V890 Barebone system comes with one 3.25-inch drive bay for a oppy disk drive. To install a oppy disk drive: 1. Remove the front panel cover. For instructions on how to remove the front panel cover, refer to page 2-3 of section “2.
2-19 ASUS V-Series M2V890 2.10 Removing the bay covers and reinstalling the front panel assembly and side cover If you installed an optical and/or oppy disk drive, remove the bay cover(s) on the front panel assembly before reinstalling it to the chassis.
2-20 Chapter 2: Basic installation.
Chapter 3 Starting up This chapter helps you power up the system and install drivers and utilities from the support CD..
3-2 Chapter 3: Starting up Press to turn ON the system 3.1 Installing an operating system The barebone system supports Windows ® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
3-3 ASUS V-Series M2V890 3.3 Support CD information The support CD that came with the system contains useful software and several utility drivers that enhance the system features. 3.3.1 Running the support CD To begin using the support CD, place the CD in your optical drive.
3-4 Chapter 3: Starting up 3.3.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. AMD Cool ‘n’ Quiet Driver Installs the AMD Cool ‘n’ Quiet driver.
3-5 ASUS V-Series M2V890 3.3.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS Cool ‘n’ Quiet Utility Installs the ASUS Cool ‘n’ Quiet utility. ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in a Windows ® environment.
3-6 Chapter 3: Starting up 3.3.4 Make Disk menu The Make Disk menu allows you to make a RAID driver disk. Anti-Virus utility The anti-virus utility scans, identies, and removes computer viruses. View the online help for detailed information. ASUS Screen Saver Installs the ASUS screen saver.
3-7 ASUS V-Series M2V890 3.3.5 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also nd this information on the inside front cover of this user guide.
3-8 Chapter 3: Starting up.
Chapter 4 Motherboard information This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
4-2 Chapter 4: Motherboard info 4.1 Introduction The V-Series M2V890 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconguration.
4-3 ASUS V-Series M2V890 4.3 Jumpers 1. Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
4-4 Chapter 4: Motherboard info 3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar).
4-5 ASUS V-Series M2V890 2. Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA hard disk and optical disk drives that allows up to 150 MB/s data transfer rates, faster than the standard parallel ATA with 133 MB/s (Ultra DMA133).
4-6 Chapter 4: Motherboard info 3 IDE connector (40-1 pin PRI_EIDE) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s). There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray.
4-7 ASUS V-Series M2V890 Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB module is purchased separately. Do not forget to connect the fan cables to the fan connectors. Insufcient air ow inside the system may damage the motherboard components.
4-8 Chapter 4: Motherboard info +12V DC GND +12V DC GND A TX12V EA TXPWR +3 Volts +3 Volts Ground +5 Volts Ground +5 Volts Ground Power OK +5V Standby +12 Volts +12 Volts +3 Volts +3 Volts -12 Volts Ground PSON# Ground Ground Ground -5 Volts +5 Volts +5 Volts +5 Volts Ground A TX power connectors 6.
4-9 ASUS V-Series M2V890 7. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports the Azalia audio standard. Connect one end of the front panel audio I/O module cable to this connector.
4-10 Chapter 4: Motherboard info 9. System panel connector (2x5 10 pin F_PANEL) This connector supports several chassis-mounted functions. • System power LED This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector.
4-11 ASUS V-Series M2V890 10. Optical drive audio In connector (4-pin CD) This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card.
4-12 Chapter 4: Motherboard info.
1 Chapter 5 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters..
5-2 Chapter 5: BIOS setup 5.1.1 Creating a bootable floppy disk 1. Do either one of the following to create a bootable oppy disk. DOS environment a. Insert a 1.44MB oppy disk into the drive. b. At the DOS prompt, type format A:/S then press <Enter>.
5-3 ASUS V-Series M2V890 2. Copy the original or the latest motherboard BIOS le to the bootable oppy disk. 5.1.2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a oppy disk and using a DOS-based utility.
5-4 Chapter 5: BIOS setup 5.1.3 AFUDOS utility The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable oppy disk with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets corrupted during the updating process.
5-5 ASUS V-Series M2V890 5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive. 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable oppy disk you created earlier.
5-6 Chapter 5: BIOS setup 5.1.4 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows ® environment.
5-7 ASUS V-Series M2V890 Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears.
5-8 Chapter 5: BIOS setup 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. 6. If you select the option to update the BIOS from a le, a window prompts you to locate the le.
5-9 ASUS V-Series M2V890 5.2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section “5.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to “Run Setup.
5-10 Chapter 5: BIOS setup 5.2.2 Menu bar The menu bar on top of the screen has the following main items: Main For changing the basic system conguration Advanced For changing the advanced system se.
5-11 ASUS V-Series M2V890 5.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items.
5-12 Chapter 5: BIOS setup 5.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. 5.3.1 System Time [xx:xx:xxxx] Allows you to set the system time. 5.3.2 System Date [Day xx/xx/xxxx] Allows you to set the system date.
5-13 ASUS V-Series M2V890 5.3.4 Primary and Secondary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information.
5-14 Chapter 5: BIOS setup PIO Mode [Auto] Selects the PIO mode. Conguration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode.
5-15 ASUS V-Series M2V890 5.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect eld values can cause the system to malfunction.
5-16 Chapter 5: BIOS setup Legacy USB Support [Enabled] Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled.
5-17 ASUS V-Series M2V890 5.4.3 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. NorthBridge Configuration Advanced Chipset Settings Warning: Setting wrong values in below sections may cause system to malfunction.
5-18 Chapter 5: BIOS setup ECC Conguration DRAM ECC Enable [Enabled] 4-Bit ECC Mode [Disabled] DRAM SCRUB REDIRECT [Disabled] DRAM BG Srub [Disabled] ECC Configuration DRAM ECC Enable [Disabled] Enables or disables the DRAM ECC that allows hardware to report and correct memory errors automatically to maintain system integrity.
5-19 ASUS V-Series M2V890 4-Bit ECC Mode [Disabled] Enables or disables the 4-Bit ECC mode. Conguration options: [Disabled] [Enabled] DRAM SCRUB REDIRECT [Disabled] Sets the system to correct DRAM ECC Errors immediately when they occur, even if background scrubbing is on.
5-20 Chapter 5: BIOS setup AGP Bridge K8M890 AGP/PCI EXPRESS Configuration OnChip VGA Frame Buffer Size [64MB] Primary Graphics Adapter [PCIE VGA] VLink Mode Supported [Auto] AGP Mode [AGP 8X] Graphics Aperture Size [128MB] OnChip VGA Frame Buffer Size [64MB] Sets the onchip VGA frame buffer size.
5-21 ASUS V-Series M2V890 5.4.4 SouthBridge VIA VT8237A Configuration Serial Port1 Address [3F8/IRQ4] Serial Port1 Mode [Normal] Serial Port2 Address [2F8/IRQ3] Serial Port2 Mode [Normal] Parallel Por.
5-22 Chapter 5: BIOS setup 5.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
5-23 ASUS V-Series M2V890 Plug and Play O/S [No] When set to [No], BIOS congures all the devices in the system. When set to [Yes] and if you install a Plug and Play operating system, the operating system congures the Plug and Play devices not required for boot.
5-24 Chapter 5: BIOS setup 5.5 Power menu The Power menu items allow you to change the settings for the Advanced Conguration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
5-25 ASUS V-Series M2V890 Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed. Conguration options: [On/Off] [Suspend] Restore on AC Power Loss [Power Off] When set to Power Off, the system goes into off state after an AC power loss.
5-26 Chapter 5: BIOS setup 5.5.5 Hardware Monitor CPU Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. Select Ignored if you do not wish to display the detected temperatures.
5-27 ASUS V-Series M2V890 5.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu. 5.6.1 Boot Device Priority Fan Auto Mode Full Speed Temp [55ºC] Sets the fan auto mode full speed temperature.
5-28 Chapter 5: BIOS setup 5.6.2 Boot Settings Configuration Set this item to [Enabled] to use the ASUS MyLogo2™ feature. Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system.
5-29 ASUS V-Series M2V890 If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section “4.3 Jumpers” for information on how to erase the RTC RAM. 5.6.3 Security The Security menu items allow you to change the system security settings.
5-30 Chapter 5: BIOS setup After you have set a supervisor password, the other items appear to allow you to change other security settings. User Access Level [Full Access] This item allows you to select the access restriction to the Setup items.
5-31 ASUS V-Series M2V890 Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Conguration options: [Setup] [Always] 5.
5-32 Chapter 5: BIOS setup Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to elds other than System Date, System Time, and Password, the BIOS asks for a conrmation before exiting.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Asus asus pc è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Asus asus pc - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Asus asus pc imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Asus asus pc ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Asus asus pc, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Asus asus pc.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Asus asus pc. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Asus asus pc insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
