Manuale d’uso / di manutenzione del prodotto None del fabbricante Nortec Industries
Vai alla pagina of 20
MES Electrode Steam Humidifiers Installation, Operation, Maintenance, Spare Parts, and Exploded Views Guide IMPORTANT: Read and save this guide for future reference.
Table of Contents INSTALLATION 1 RECEIVING EQUIPMENT .........................................1 PRINCIPAL OF OPERATION .......................................1 WATER SUPPLY AND PLUMBING ....................................2 WATER CONNECTION ..........
INSTALLATION RECEIVING EQUIPMENT 1. Check packing slip to ensure ALL material has been received. 2. Inspect box for damage and note on shipping waybill accordingly. 3. After unpacking, inspect unit for damage and if damage is found, advise shipper as soon as possible.
WATER SUPPLY AND PLUMBING 1. The fill valve is sized for an extended water pressure range of 30 to 80 psi. 2. For cases below 15 psi add a pressure boost pump, notify the factory and a fill valve with an oversized orifice will be supplied. 3. For cases above 80 psi, install a pressure reducing valve in the water feed line to the unit.
The red light simply acts as a safety to shut off the fill valve and prevent over-filling. With the red light on, the water in the cylinder will continue to heat and, after a few minutes, start to boil.
dependent on water supply conditions and humidifier usage. Failure to replace the cylinder at the end of cylinder life may result in unit damage. NORTEC is not responsible for any damages resulting from, or attributable to, the failure to replace a used cylinder (see Manufacturer’s Warranty).
FOAMING: The phenomenon which can occur in water when the impurities, already in the water reach an excess concentration as a result of boiling away pure water and the continued boiling action agitating the contained water.
Water remains at high level and won’t concentrate: This is normal on cold start-up and can be accelerated by adding maximum 1/2 tsp. of dissolved salt to the cylinder (through the plastic fill cup) on fill cycle. See “Low Water Conductivity” section of this manual.
DIAGNOSTIC PROCEDURES - TROUBLESHOOTING GUIDE Unit Status Lamp Symptom Corrective actions Yellow Green On On Maximum water level inside cylinder. This usually happens on initial start-up after replacing the cylinder (normal). Water is concentrated with minerals inside the cylinder.
Software require ments for Modbus RT U Modbus addresses : 4XXXX – R/W 3XXXX - R Comm and Description MODBUS address Details Output Control OFF Disables the hum idifier and places the hum idifier in .
-9- Set MODBUS parity * Change the humidifier controller’s MODBUS parity. Range is None, Even, Odd This setting shall be non-volatile with a default setting of Even.
-1 0- Maxim um production The r ated maxim um s team production for t he humidifier 30802 V a l u ew r i t t e ni n t oU n i tt y p e (40600) is als o stored here Alarm s The hum idifier shall desc ri.
-1 1- MES -U/MES-P HUMIDIFIER PHYSICAL DA T A MESU DIM 10/19/98 WEIGHTS (DR Y) DIMEN S I O N S NOTES: 1. FOR HEIGHT OF 5 LB PVC USE HEIGHT OF 1 0 LB MODEL. 2. PVC = PRIMARY VOL T AGE CONNECTION. 3. MODEL SHOWN: 163-91X5 (CONFIGURA TION #5) WITH CP (CLOSED PLUMBING) COVER REMOVED.
-1 2- MES-U INTERNAL AND FIELD WIRING WIRING DIAGRAM number 150-6240 REV . B (For PVC or L VC unit with remote or att ached electrical) STEAM CYLINDER NOTE: SOLID LINES WIRING BY OTHERS HIGH VOL T AGE.
- 13-.
- -14- PO S . DESCRIPTION C om m ents NORT E C 208/ 380/ 208/ 380/ 208/ 380/ 208/ 380/ NO PA RT 230/ 460/ 230V 460/ 230V 460/ 230V 460/ NUMBER 277V 575V 575V 575V 575V 1 C y li nder - T o order r epl ac em ent c ylinder, quote the 3- digi t C ons ult 1 1 1 1 1 1 1 1 num ber on t he cy l.
- 15-.
.
LIMITED WARRANTY Walter Meier Inc. and/or Walter Meier Ltd. (hereinafter collectively referred to as THE COMPANY), warrant for a period of two years from date of shipment, that THE COMPANY’s manufactured and assembled products, not otherwise expressly warranted are free from defects in material and workmanship.
Walter Meier (Climate USA) Inc. 826 Proctor Avenue, Ogdensburg, New York 13669 Walter Meier (Climate Canada) Ltd. 2740 Fenton Road, Ottawa, Ontario K1T3T7 Tel: 866 NORTEC 1 Fax: 613 822 7964 northamerica.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Nortec Industries None è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Nortec Industries None - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Nortec Industries None imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Nortec Industries None ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Nortec Industries None, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Nortec Industries None.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Nortec Industries None. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Nortec Industries None insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
