Manuale d’uso / di manutenzione del prodotto LT31CS del fabbricante MTD
Vai alla pagina of 24
Operator’ s Manual L T31CS 2-Cycle Petr ol T rimmer/Brushcutter IMPORT ANT : Read safety rules and instructions carefully befor e operating equipment.
2 T ABLE OF CONTENTS Content P age Important Safe Operation Practices ............................................................... 3 Know Y our T rimmer ........................................................................................ 6 Assembling Y our T rimmer .
3 This Symbol Points Out Important Safety Information Which, If Not Followed, Could Endanger The Personal Safety And/or Property Of Y ourself And Others. Read And Follow All Instructions In This Manual Befor e Attempting T o Operate Y our Cultivator .
•W ear heavy , long pants, boots and gloves. Do not wear loose clothing, jewelry , short pants, sandals or go barefoot. Secur e hair above shoulder level. • The cutting guard must always be in place while operating the unit as a trimmer . Do not operate unit without both trimming lines extended, and the proper line installed.
5 SYMBOL MEANING • WEAR HEAD PRO TECTION W ARNING: Falling objects can cause severe head injury . W ear head protection when operating this unit. • ON/OFF STOP CONTROL ON / ST ART / RUN • ON/OFF STOP CONTROL OFF or STOP •H OT SURF A CE WARNING Do not touch a hot muffler or cylinder .
6 SECTION 2: KNOW Y OUR TRIMMER KNOW YOUR UNIT APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around tr ees, fences, etc.
SECTION 3: ASSEMBLING Y OUR TRIMMER 7 FIGURE 1 FIGURE 2 FIGURE 3 Decal On some units, the J-handle may be pre-installed, r equiring only screw loosening and J-handle adjustment tailor ed to the operator . Go to step 6 to adjust the J-handle if it is pre-installed.
FIGURE 5 FIGURE 4 INST ALLING THE HARNESS W ARNING: Always use the shoulder harness when using the cutting blade to avoid serious personal injury . 1. Push the strap thr ough the centre of the buckle. 2. Pull the strap over the cr oss bar and down through the slot in the buckle, Figure 4.
9 Remove the Cutting Head W ARNING: The gear housing gets hot with use and can result in injury to the operator . When the unit is turned off it remains hot for a short time. Do not touch the gear housing until it has cooled. 1. Align the shaft bushing hole with the locking r od slot and insert the locking rod into the shaft bushing hole, Figure 8.
NOTE: The blade retainer must be installed on the output shaft in the position shown for the cutting head to work correctly . 6. Remove the locking r od.
RECOMMENDED OIL TYPE Use a high quality oil formulated for use in 2-cycle, air -cooled engines. RECOMMENDED FUEL TYPE Always use clean, fresh, unleaded petr ol (gasoline) that is less than 60 days old. W ARNING: Petr ol (gasoline) is extremely flammable and its vapors can explode if they are ignited.
ST ARTING INSTRUCTIONS W ARNING: Operate this unit only in a well ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. W ARNING: A void accidental starting. Be in the starting position when pulling the starter rope, Figure 18.
For best results, tap the Bump Head™ on bar e ground or hard soil. If line r elease is attempted in tall grass, the engine may stall. Always keep the trimming line fully extended. Line release becomes mor e difficult as the cutting line becomes shorter .
FIGURE 23 W ARNING: The blade continues to spin after the engine is turned off. The coasting blade can seriously cut you if accidentally touched. • Swing the unit in the same direction as the blade spins, which increases the cutting action. •M ove forward to the next ar ea to be cut after the r eturn swing and plant feet again.
15 SECTION 5: MAINT AINING Y OUR TRIMMER NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to an authorized service dealer . MAINTENANCE SCHEDULE These requir ed maintenance procedur es should be performed at the frequency stated in the table.
16 NOTE: SplitLine™ can only be used with the inner reel containing the slotted holes. Single line can be used on either type of inner reel. Use Figure 27 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit.
17 INST ALLING A PREWOUND REEL 1. Hold the outer spool with one hand and unscrew the bump knob clockwise, Figure 15. Inspect the bolt inside the bump knob to make sure it moves fr eely . Replace the bump knob if damaged. 2. Remove the old inner reel fr om the outer spool, Figure 24.
18 CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder . 4. Install a corr ectly gapped spark plug in the cylinder head. Tighten by turning the 5/8 in. socket clockwise until snug. If using a torque wr ench torque to: 12.
19 NOTE: If exhaust gasket is torn or damaged, replace with a new gasket before reassembling muffler . 4. Using a small flatblade screwdriver , carefully pry up the spark arrestor fr om the recessed hole, Figur e 41. Remove the spark arrestor fr om the muffler .
CLEANING THE UNIT W ARNING: To avoid serious personal injury , always tur n the unit off and allow it to cool before you clean or perform any maintenance on it. • Use a small brush to clean off the outside of the unit and to keep the air vents free of obstructions.
ENGINE WILL NOT ST ART CAUSE A CTION Empty fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fill fuel tank with properly mixed fuel Primer bulb wasn't pressed enough . . . . . . . . . . . . . . . .Press primer bulb fully and slowly 5-7 times Engine flooded .
ENGINE Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9: NOTES 23.
OPERA TOR’S MANUAL P ART NO. 769-00304 8/02 PRINTED IN THE USA SECTION 9: NOTES Cont....
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il MTD LT31CS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del MTD LT31CS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso MTD LT31CS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul MTD LT31CS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il MTD LT31CS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del MTD LT31CS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il MTD LT31CS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo MTD LT31CS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
