Manuale d’uso / di manutenzione del prodotto WL7200U del fabbricante Mitsubishi
Vai alla pagina of 68
U WL7200 This User Manual is important to you. Please r ead it befor e using your pr ojector . LCD PROJECTOR MODEL WL7200U User Manual.
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 Contents Important safeguards ........................................................................................................................ 4 Preparing your pr ojector ...................................................................
EN-4 Important safeguar ds Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 Important safeguards (continued) WARNING: Unplug immediately if there is something wrong with your pr ojector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fir e or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your projector 1 Checking accessories The following accessories are pr ovided with this projector . Check to be sur e that all of the accessories are packed in the package.
EN-7 Overview 6 7 11 12 9 10 3 2 1 4 5 13 8 6 7 8 9 10 1 3 4 5 2 1 Speaker 2 Lens release button 3 Indicators 4 Air inlet grille/Filter cover 5 Air inlet grille 6 Lens 7 Remote control sensor (fr ont).
EN-8 2 1 123 Preparing your projector (continued) Bottom side Indicators 1 Lock bar (SECURITY ANCHOR) t "UUBDIBDIBJOFUDUPUIJTMPDLCBSUPBODIPS the projector.
EN-9 Using the r emote control Using the wir ed r emote contr ol Attached remote contr ol for this projector can be used as a wired r emote control with remote contr ol cable. Wired remote contr ol is useful for operating in a distance or outside of the operating area.
EN-10 Using the remote control (continued) Setting the ID number of the r emote contr ol Y ou can control multiple projectors collectively or individually using one remote contr ol by setting the ID number (CONTROLLER ID) of the remote contr ol.
EN-11 Setting up your pr ojector Befor e setting up Before setting up the pr ojector , check the operating environment. If the environmental r equirements are not satisfied, the pr ojector may break down or fail. Setup environment The allowable operating temperature varies depending on the HIGH AL TITUDE MODE setting.
EN-12 Setting up your pr ojector (continued) Setup adjustment How to turn on the projector When you have to turn on the projector for setup adjustment, see the following pages: t 1MVHHJOHUIFQ.
EN-13 Setting HIGH AL TITUDE MODE t 4FU)*()"- 5*56%&.0%&JOUIF'&" 563&NFOV according to the altitude at which you use the projector . The default setting is ST ANDARD. t 4FMFDU45 "/%"3%XIFOVTJOHUIFQS PKFDUPSBUBO altitude from 0 to 1500 meters.
EN-14 Setting up your pr ojector (continued) Adjustment using the KEYSTONE mode: When the screen and the pr ojector are not placed perpendicularly to each other , pr ojected images become trapezoidal.
EN-15 Setting up your pr ojector (continued) LOWER RIGHT , LOWER LEFT , UPPER RIGHT , or UPPER LEFT menu Y ou can adjust the horizontal or vertical position of the selected corner . Example: Adjustment of the upper left corner position (UPPER LEFT) Press the button.
EN-16 Setting up your pr ojector (continued) t 8IFOUIFIPSJ[POUBMBSDBEKVTUNFOUJTQPTJUJWF (or the ARC is adjusted in the direction) Press the button. Press the button. Press the button. Press the button.
EN-17 Setting up your pr ojector (continued) Fr ont pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector .
EN-18 AUDIO OUT 2 1 2 1 Viewing computer images 2 1 A. Connecting the pr ojector to a computer Preparation: t .BLFTVSFUIBUUIFQPXFSPGUIFQS PKFDUPSBOEUIBUPGUIFDPNQ.
EN-19 1 Viewing computer images (continued) 1. Plug the attached power cor d into the power cord inlet of this projector . 2. Plug the other end of the power cor d into a power outlet.
EN-20 C. Installing the terminal cover This projector includes a terminal cover . If necessary , install the terminal cover to the projector . 1. Fit two hooks of the terminal cover into the pr ojector . (a) Viewing computer images (continued) Important: t Don’t carry the pr ojector by the terminal cover .
EN-21 Viewing computer images (continued) D. Pr ojecting images Preparation: t 3FNPWFUIFMFOTDBQ COMPUTER 1, 2 buttons POWER indicator ST A TUS indicator DVI-D(HDCP) button ENTER button .
EN-22 Viewing computer images (continued) 9. Pr ess the ZOOM/FOCUS button to display the ZOOM/FOCUS menu. 10. Adjust with the or button to get an approximate size.
EN-23 Blanking the screen temporarily (BLANK) The video and audio signals are temporarily muted when the BLANK button is pr essed. Y ou will hear an operating sound inside the projector .
EN-24 Viewing computer images (continued) Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the scr een to be used or your preference.
EN-25 Viewing video images Connecting to a video player , etc. 1. Connect one end of a commer cially available BNC cable to the VIDEO IN terminal of the projector . 2. Connect the other end of the BNC cable to the video output terminal of the video equipment.
EN-26 Viewing video images (continued) Projector + DVD player or HDTV decoder Some DVD players have an output connector for 3-line fitting (Y , C B , C R ). When connecting such DVD player with this projector , use the COMPUTER/COMPONENT/VIDEO IN 2 terminals.
EN-27 Connection (for video equipment having a DVI-D terminal) Equipment having a DVI-D terminal T o DVI-D terminal DVI cable (option) COMPUTER/COMPONENT/ VIDEO DVI-D IN (HDCP) Audio cable (option) T .
EN-28 Viewing video images (continued) D. Pr ojecting images Preparation: t 3FNPWFUIFMFOTDBQ COMPUTER 1, 2 buttons POWER indicator ST A TUS indicator DVI-D(HDCP) button S-VIDEO button V.
EN-29 11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the scr een. 12. Press the or button to adjust the vertical position and or button to adjust the horizontal position of the displayed image.
EN-30 Menu operation Y ou can make various settings using the displayed menus. Following 6 menus are displayed. IMAGE menu (page 32) INSTALLATION menu (page 33) FEATURE menu (page 34) INFORMATION menu.
EN-31 How to set the menus 1. Pr ess the MENU button. t 5IFNFOVTFMFDUJPOCBSJTEJTQMBZFE IMAGE opt. Selectable menus are displayed by icons. (The menu icon being selected is displayed on a blue background.) The name of the menu being selected is displayed.
EN-32 IMAGE menu COMPUTER 0 COLOR 0 TINT 0 SHARPNESS ADVANCED MENU NCM SUPER RESOLUTION IMAGE BRIGHTNESS 0 COLOR ENHANCER AUTO CONTRAST ST ANDARD COLOR TEMP .
EN-33 INSTALLATION menu INST ALLA TION LENS LOCK LENS SHIFT LOCK ZOOM/FOCUS LOCK LENS SHIFT RESET OFF OFF opt. OK INST ALLA TION LAMP MODE ST ANDARD LOW OFF ST ANDBY MODE IMAGE REVERSE LENS LOCK opt.
EN-34 FEA TURE menu FEA TURE ADVANCED MENU SETUP SCART INPUT AUTO AUTO OFF STANDARD OFF VIDEO SIGNAL LAMP WARNING HIDE OSD opt. LANGUAGE ADVANCED MENU FEA TURE ASPECT PROJECTOR ID NORMAL (FULL) AUTO English ALL DISPLA Y INPUT ENTER CINEMA MODE P ASSWORD FUNCTION MENU POSITION opt.
EN-35 ITEM SETTING FUNCTION ADV ANCED MENU ENTER The ADV ANCED MENU is displayed for the following settings. VIDEO SIGNAL AUTO / NTSC / P AL / SECAM / 4.43NTSC / P AL-M / P AL-N / P AL-60 When AUTO is selected, the appropriate video format is automatically selected depending on the input signal.
EN-36 SIGNAL menu R G B R G B V H A U 0 100% COMPUTER INPUT AUTO OVER SCAN HOLD USER FINE SYNC. SIGNAL VERT . POSITION 0 MEMORY CALL RESOLUTION (MEMORIZE ) AUTO HORIZ. POSITION 0 TRACKING opt. opt. SIGNAL RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONT AL FREQUENCY HORIZ.
EN-37 NETWORK menu NETWORK IP CONFIG opt. DHCP IP ADDRESS SUBNET MASK DEF AUL T GATEW A Y 0. 0. 0. 0 MAC ADDRESS SAVE SETTINGS ON 0. 0. 0. 0 OK CONTROL SYSTEM NETWORK P ASSWORD NETWORK NETWORK CERTIFICA TION PROJECTOR NAME IP CONFIG NETWORK RESET opt.
EN-38 INFORMA TION menu 60.00 Hz RESOLUTION 1024 x 768 VERTICAL FREQUENCY 48.36 kHz 5WIRE HORIZONT AL FREQUENCY SYNC. TYPE SERIAL NUMBER INFORMA TION ******** ... COMPUTER1 INPUT opt. RG HV B LAMP TIME (LOW) **** H ITEM DESCRIPTION LAMP TIME (LOW) This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP is LOW .
EN-39 Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 31 for menu setting.) 1. Display the IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pr essing the or button.
EN-40 T o cancel the menu: 7. Pr ess the MENU button. T o enable the stored color temperature: 1. Set COLOR TEMP . to USER in the IMAGE menu. About color temperature Color temperature is a way to show the dif ferences in white. White of which temperature is low appears r eddish.
EN-41 Adjusting the fineness of the image (SUPER RESOLUTION): Y ou can adjust the fineness of the image using the menu. (See page 31 for menu setting.) With the IMAGE menu: 1. Display the IMAGE menu. 2. Select SUPER RESOLUTION by pr essing the or button.
EN-42 Adjusting pr ojected images (continued) How to adjust the computer image This projector automatically selects a pr oper signal format according to the type of video signal supplied from the computer . However , video signals from the computer may not be projected corr ectly depending on the types of the computer and images to be projected.
EN-43 How to adjust the image supplied from the computer using the menu: Carry out the following procedur es according to the symptoms. Wide strips appear . ……………………………………… Adjust TRACKING in the SIGNAL menu. The projected image flickers.
EN-44 Initial network settings Y ou can set the network of the projector using the menu. CONTROL SYSTEM NETWORK P ASSWORD NETWORK NETWORK CERTIFICA TION PROJECTOR NAME IP CONFIG NETWORK RESET opt. ST ANDARD ENTER ENTER OK NETWORK REST ART OK ON Setting Pr ojector Name (See page 31 for menu setting.
EN-45 CLEAR key: ..... Deleting all the enter ed characters. t : PVDBOFOUFSOVNCFSTCZQSFTTJOHUIFOVNCFS buttons (0 to 9) while holding down the NUM button on the remote contr ol. t 5IFEFGBVMUQBTTXPSEJTiBENJOw 5.
EN-46 t : PVDBOFOUFSOVNCFSTCZQSFTTJOHUIFOVNCFS buttons (0 to 9) while holding down the NUM button on the remote contr ol. 5. When selecting OK, the setting is completed as the IP ADDRESS stored temporarily . However , when selecting CANCEL, the setting is completed without storing.
EN-47 Initialization of Network Settings (See page 31 for menu setting.) 1. Display the NETWORK menu. 2. Press the or button to select NETWORK RESET . NETWORK RESET OK 3. Pr ess the ENTER button. t $POmSNBUJPOEJBMPHBQQFBST 4. Pr ess the ENTER button again, and the Network Settings can be initialized (except for IP CONFIG).
EN-48 t 5IFJNBHFXJUIJOUIFPVUFSFEHFTPGUIFSFE frame is captured. t 5IFDBQUVSFEJNBHFJTEJTQMBZFEJOUIF3&"- mode automatically . CAPTURE : ENTER + ENTER CANCEL : MENU CAPTURE : ENTER X2 CANCEL : MENU 12.
EN-49 Passwor d function This projector is equipped with the passwor d function that is designed for prevention of wr ong operation by children and r estriction on operation by other than specified users. The password function has 3 modes as follows.
EN-50 Split Y ou can split the screen in two and display a computer image on the left screen and a video image on the right screen. Left screen Right screen T o use the split mode: 1.
EN-51 Important: t 8IFOZPVTFU$0/530-4:45&.UP$3&4530/ in the NETWORK menu, the web control for Crestr on is enabled. For such control, Adobe Flash Player should be installed in advance. Y ou can download Adobe Flash Player from the website of Adobe Systems Incorporated.
EN-52 Connection For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM. When ST ANDBY MODE of the INST ALLA TION menu of the projector is set to LOW , the network function is disabled. T o enable the network function, set ST ANDBY MODE to ST ANDARD or LAN.
EN-53 Replacing the lamp This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may burn out or its brightness may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to r eplace the lamp with a new lamp separately sold that is exclusive to this projector .
EN-54 Replacing the lamp (continued) T o r eplace the lamp: 1. Unplug the power cor d. 2. Loosen two scr ews (a) that are securing the lamp cover using a Philips screwdriver and r emove the lamp cover (b) from the pr ojector . (b) (a) 3. Loosen two scr ews (c) that are securing the lamp box to be removed using a Philips scr ewdriver .
EN-55 When removing the lamp fr om the ceiling-mounted projector When removing the lamp fr om the ceiling-mounted projector , use the lamp r eplacement tray packed with the projector or option lamp to pr event glass fragments from scattering.
EN-56 Roll-up filter This projector is equipped with a r oll-up filter . The clogged filter rolls and r eplaces with a clean one periodically . When all the filters are r olled up, you can replace the filter cartridge with a new one.
EN-57 Y ou can replace the lens on this projector . The lens can be replaced with the separately sold option lens according to the usage envir onment of the projector .
EN-58 T roubleshooting Before asking for r epair of the projector , check the following. If the symptom persists, stop using the pr ojector , be sure to unplug the power plug, and then contact your dealer . No image appears on the screen. Problem Solution Power can not be turned on.
EN-59 T r oubleshooting (continued) No image appears on the screen. (continued) Problem Solution The screen for entering the password appears. t 1 "44803%'6/$5*0/JOUIF'&" 563&NFOVIBTCFFOTFUUP%*41-" :*/165 to enable the password lock.
EN-60 T r oubleshooting (continued) Images are not displayed corr ectly . (continued) Problem Solution Hue is not appropriate. t $IFDLUIBUUIFDBCMFTDPOOFDUFEUPUIFFYUFSOBMEFWJDFTBSFOPUCSPLFO Tint in projected images is incorrect.
EN-61 T r oubleshooting (continued) Problem Solution FOCUS/ZOOM doesn’t work. Lens shift doesn’t work. t $IFDLUIBU-&/4-0$,JOUIF*/45 "--" 5*0/NFOVJTOU0/ (See page 33.) If the following problem occurs after the lamp is r eplaced, check the following first.
EN-62 Indicators This projector has 3 indicators, each of which shows the operation condition of the pr ojector . The following offer solutions to possible pr oblems.
EN-63 Specifications The specifications and outside appearance of the projector ar e subject to change without prior notice. T ype LCD projector Model WL7200U Display technology 0.
EN-64 Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal mode Resolution (H x V) Horizontal frequency (kHz) V ertical frequency (Hz) Normal mode (H x V) Real mode (H x V) TV60, 480i (525i) 720 x 480 15.
EN-65 481 179 101* 418 Dimension drawings (unit: mm) Specifications (continued) Specification of RGB signals in each computer mode of the projector (continued) Important: t Some computers aren’ t compatible with the projector . t The projector’ s maximum r esolution is 1280 x 800 pixels.
EN-66 Specifications (continued) Specification of the attached lens With short throw zoom lens (OL-XL7100SZ) F No. F2.0 - F2.6 Focal distance f = 19.
EN-67 Specifications (continued) With rear pr ojection short throw (OL-XL7100FR) F No. F2.2 Focal distance f = 12.9 mm Focus Electrical drive Picture size 40 inch (86 cm X 54 cm) - 200 inch (431 cm X.
1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N U-B.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Mitsubishi WL7200U è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Mitsubishi WL7200U - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Mitsubishi WL7200U imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Mitsubishi WL7200U ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Mitsubishi WL7200U, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Mitsubishi WL7200U.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Mitsubishi WL7200U. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Mitsubishi WL7200U insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
