Manuale d’uso / di manutenzione del prodotto UTM560 del fabbricante Abocom
Vai alla pagina of 19
USB V.90 TINY MODEM Quick Installation Guide.
FCC REGULATORY STATEMENTS The United States Federal Com munication Com mission (FCC) and the Canadian Department of Com munications have established certain rules governing the use of modem s and other electronic equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pr ovide reasonable protection against harmful interference in a residential installation.
Table of Contents Introduction .............................................................1 S PECIFICATIONS .....................................................1 Modem ............................................................... 1 Fax ..........
Introduction The USB V.90 Tiny Modem com plies with the Universal Serial Bus f unctionality built in Windows 98/2000/Millennium. It is com patible with Bell, ITU-T (formerly CCITT) and Hayes AT com mands. The USB V.90 Tiny Modem enables you enjoy all the benefit offered by USB technol ogy and get a faster and easier Internet access.
- 2 - System Requirements A Pentium processor-based personal computer 166MMX or above At least 16 MB of R AM An USB port Microsoft Windows 98/2000/Millennium A CD-ROM drive.
Hardware Installation 1. Locate the USB host port of your system. Connects the USB Type A connector to the USB host port on your com puter. 2. Connects the phone line to the phone line jack - 3 -.
Software Installation Installation for Windows 98 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows 98 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next.
- 5 - you load the device driver. Click Next. Windows will start searching for the appr opriate driver for the software installation. 4. Click Next. 5. Click Finish. The software installation is successfully completed. 6. When the following dialog box appears, select the country/locati on where you are, and click Enable PBX.
- 6 - Setup Diagnostics You can perform the foll owing steps to check if your USB V.90 Tiny Modem is well installed. 1. Go to Start → Settings → Control Panel → Modems . 2. When the Modems Properties dialog box appears, select the Diagnostics tab.
Installation for Windows 2000 1. Once the USB V.90 Tiny Modem is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next. 2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the device driver compact disc into the CD-ROM drive.
- 8 - 4. Click Browse button and select the drive where you load the device driver (for exam ple: G:WIN2K ). Click OK. Windows will start searching for the appropriate driver for the software installation. 5. Click Next to continue. 6. Click Yes. 7. Click Finish.
- 9 - Setup Diagnostics To verify whether your USB V.90 Tiny Modem exists in your com puter and is enabled, go t o My Computer → Control Panel → System. Click the Device Manager tab. If the USB V.90 TINY MODEM and Network adapters are found, it means that your Network dev ice is well installed.
Installation for Windows Millennium 1. When the USB V.90 Tiny Modem is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Load the device driver com pact disc into the CD-ROM of your system and select Specify a location.
- 11 - 3. Expect a minor dela y for Windows to search for the appropriate driver for the device. C lick Next. 4. Click Finish. The installation pr ogram will continue. 5. Select Specify the location of the driver (Advanced) and click Next. 6. When the above figure appears, repeat step 2, namely, select Specify a location.
- 12 - 7. Click Next . 8. When Windows prom pt you “ Modem Country Selection ”, choose the country where you locate. Select the Enable PBX check box and click OK.
Setup Diagnostics 1. To verify if the USB V.90 Tiny Modem is well installed and enabled, y ou can perform the following steps. 2. Go to Start Settings Control Panel Modems. 3. When the Modems Properties dialog box appears, select the Diagnostics tab.
Internet Access 1. Go to My Computer . 2. Select Dial-Up Networking . 3. Double-click Make a New Connection , a dialogue box will appear for you to nam e the new connection and select the device. Nam e the new connection appropriatel y and click Next .
- 15 - 7. Now, you are ready to connect to the Internet..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Abocom UTM560 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Abocom UTM560 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Abocom UTM560 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Abocom UTM560 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Abocom UTM560, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Abocom UTM560.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Abocom UTM560. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Abocom UTM560 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
