Manuale d’uso / di manutenzione del prodotto 938018 - SS722EC del fabbricante Ariens
Vai alla pagina of 24
Owner/Operator Man ual Models 938017 - SS5 22EC 938018 - SS7 22EC Sno-Thro ® 03392200 5/08 Printed in USA U.S. Patents 5758436 and 5966846 ENGLISH.
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls & Feat ur es . . . . . . . . . . . . . . . . 10 Oper a t ion . . . . . . . . . . . . . . . . . . . . .
GB - 3 • Record Unit Model and Serial numbers here. • Record Engine Model and Ser ial number here. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 SAFETY ALERT S Look for these symbols to point out important safety precautions. They mean: Attention! Personal Safety Is Inv olved! Become Alert! Obey The Mess age! The safety alert symbols abo ve and signal words below are used on decals and in this manual.
GB - 5 SAFETY DECALS AND LOCATIONS AL WA YS replace m issing or dam aged Safety Deca l s. R e fe r to fi gu r e 2 be l o w fo r Sa f ety Decal locations. 1. DANGER! • Read operator ’s manual. • Allow operation only by properly trained adults, never children.
GB - 6 SAFETY RULES Read, understand, and follow all safety practices in Ow ner/Operator M anual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or damage t o unit. AL WA YS remov e key and/or wire from spark plug before assem bly , maintenance or service.
GB - 7 Understand: • How to operate all controls. • The functions of all controls. • How to STOP in an em ergenc y . Before starting engine, disengage control(s). Use only approved extension cords and receptacles when starting units equipped with electric starter .
GB - 8 If fuel is spilled on clot hing, change clothing immediately . Before tipping unit up onto housing, remov e fuel so no spills wil l occur. Ensure unit is secure and will not tip over during maintenance. AL WA YS keep prote ctive structures , guards, and panels in good repair , in place and securely fastened.
GB - 9 Discha rge Chute A ssembly 1. Remove bolt and nut from rear of discharge chute (figure 4). 2. T ip discharge chute up and install hardware just rem oved. Tighten hardware at r ear of discharge chute first, then sides. Discharge Chute Crank Asse mbly 1.
GB - 10 1. Auger Clutch Bail 2. Handlebar 3. Discharge Chute Crank 4. Handlebar Wing Knob 5. Sp ark Pl ug Acc ess C over 6. Discharge Chute Handle 7. Exhaust 8. Discharge Chute Deflector 9. Auger Housing 10. Auger 1 1. Ignition Switch 12. Fuel Level Indicat or 13.
GB - 1 1 CONTROLS AND FEATURES See figure 6 for controls and features locations. Ignition Sw itch Ignition switch is operated by a removable key that has two positions. 1. STOP 2. RUN Auger Clutch Bail Squeeze auger clutch bail against handlebar to engage auger.
GB - 12 Discharge Chute De flector AL WA YS position discharge chute deflector at a safe angle before starting engine. DO NOT throw snow any higher than necessary . Pull chute deflector handle u pward to throw snow lower . P ush chut e deflector handle downward to throw s now higher .
GB - 13 STOPPING IN AN EMERGENCY Immediately release au ger clutch bail t o stop unit in an emergency . S top engine, remove key and wait for all rotating parts to stop before leaving operator ’s position. ST ARTING AND SHUTTING OFF IMPORT ANT : Allow unit and en gine to adjust to the outdoor t emperature before clearing snow .
GB - 14 Tips f o r Op e r a t i o n Snow is best removed as soon as possible after a snow fall. T o clear an area, run unit in an overlapping series of paths. F or large ar eas, start in the middle and throw snow to each side, so s now is not cleared more than once.
GB - 15 SERV ICE PO SI T ION Place unit on a flat level surface. DRIVE BELT REPLACEME NT Remove (Fi gure 8) 1. Remov e cowl. 2. Disconnec t extension spring on idler arm/brake. 3. Remove auger drive pulley . 4. Remove old belt. Inst all (Figure 8) 1. Install new belt on drive pulley and idlers.
GB - 16 DISCHARGE CHUTE DEFLECTOR ADJUSTMENT If discharge chute def lector does not s tay in position while throwing snow , adjust chute by tightening fasteners (figur e 10). DRIVE BELT ADJUSTMENT Adjust Auger Control Cab le (Figure 1 1) 1. Meas ure bail spring length with auger clutch bail DISENGAGED.
GB - 17 3. Loosen belt finger and rotate until there is 1/32 – 1/16 in. (0.8 – 1.6 m m) gap between belt finger and drive belt. 4. Tighten belt finger . 5. Rechec k gap bet ween belt finger and drive belt. Adjust belt f inger until there is 1/32 – 1/16 in.
GB - 18 SHORT T ERM IMPORT ANT : NEVER spray unit with high pressure wa ter or st ore unit outdoors. Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Inspect unit for v isible signs of wear, breakage or damag e.
GB - 19 T R OUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ st art 1. Key not in RUN positi on. 2. Fuel tank empty . 3. Clogged fuel filter . 4. Faulty electric starter or wire connections. 1. T urn key to RUN position. 2. Fill fuel t ank.
GB - 20 SPE CIFICATIONS Model Num ber 938017 938018 Description SS522EC SS722E C Engine - T ecumseh (Two-Cycle) TH139SA TH139SP Engine Power – hp (kW) at Maximum RPM 5 (3.73) 7 (5.22) Fast Idle S peed – RPM (min -1 ) 3950 ± 150 Displacement – in.
.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® MOWE R | BYNORM ® | EVERRIDE ® | GREAT DA NE ® Snow_2008 22 Three-Y ear Limi ted Sno-Thro ® Wa r r a n t y Ariens Company (Ariens).
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNORM ® | EVERRIDE ® | GREA T DANE ® Snow_2008 23 Limitations • Batteries are w arranted only for a peri od of 12 m onths after date of purcha se, on a p rorat ed basis. For the first 90 da ys of the war ranty peri od, a defective battery will be replaced free of charge.
Ariens Company 655 West Ryan St reet Brillion, W I 541 10-1072 920-756-2141 Fax 920-756-2407 www .ariens.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ariens 938018 - SS722EC è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ariens 938018 - SS722EC - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ariens 938018 - SS722EC imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ariens 938018 - SS722EC ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ariens 938018 - SS722EC, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ariens 938018 - SS722EC.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ariens 938018 - SS722EC. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ariens 938018 - SS722EC insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
