Manuale d’uso / di manutenzione del prodotto FX3U-CF-ADP del fabbricante Mitsubishi Electronics
Vai alla pagina of 124
FX 3U -CF-ADP USER'S MANUAL.
.
(1) Before installation, operation, maintenance or inspection of this product, thoroughly read through and understand this manual and the associated manuals. Also, take care to handle the module properly and safely. This manual classifies the safety precautions into two categories: and .
Safety Precautions (Read these precautions before using.) (2) 2. INSTALLATION PRECAUTIONS 3. WIRING PRECAUTIONS Reference • Make sure to sh ut down all pha ses of the power sup ply external ly before inst alling the FX 3U -CF-ADP. Failure to do so may ca use elec tric shock or damage t o the pro duct.
Safety Precautions (Read these precautions before using.) (3) 4. STARTUP AND MAINTEN ANCE PRECAUTION S 5. DISPOSAL PRECAUTIONS 6. TRANSPORTATION PRECAUTIONS Reference • Make sure to co nn e ct the battery co rre c t ly . Do n ot c ha rg e, dis as s emb le , heat, shor t- cir cuit, or expo se the battery to fire.
(4).
1 FX 3U -CF-ADP User's Manual FX 3U -CF-ADP User's Manual Foreword This manual describes the FX 3U -CF-ADP CF card special adapter and should be read and understood before attempting to install the hardware. Store this manual in a safe place so that you can take it out and read it whenever necessary.
2 FX 3U -CF-ADP User's Manual Outline Precautions • This manual provides information for the use of the FX 3U -CF-ADP CF card special adapter. The manual has been written to be used by trained and competent personnel.
3 FX 3U -CF-ADP User's Manual Table of Contents Table of Contents SAFETY PRECAUTIONS .................................................... ........................................... ... (1) Standards ................... ........... ..............
4 FX 3U -CF-ADP User's Manual Table of Contents 5. Wiring 28 5.1 Which Power Supply Cable to Use ............................................................................................... 29 5.1.1 Power supply cable ........................ .
5 FX 3U -CF-ADP User's Manual Table of Contents 8.7 FNC 304 - FLCMD / FX 3U -CF-ADP command ............................................................................. 74 8.7.1 Detailed explanation of setting data ..................... ........
6 FX 3U -CF-ADP User's Manual Table of Contents Appendix B: Version Information 113 Appendix B-1 Version information .................. ... .......... ................ ............. ................ ................ 11 3 Appendix B-1-1 Version check method .
Standards 7 FX 3U -CF-ADP User's Manual Standards Certification of UL, cUL standards FX 3U -CF-ADP units comply with the UL standards (UL, cUL). UL, cUL File number :E95239 Regarding the standards that comply with the main unit, pl ease refer to either the FX series product catalog or consult with your nearest Mitsubishi product provider.
Standards 8 FX 3U -CF-ADP User's Manual Caution to conform with EC Directives • Installation in Enclosure Programmable logic controllers are open-type devices that must be installed and used within conductive control cabinets. Please use the programmable logic c ontroller while installed within a c onductive shielded control cabinet.
Associated Manuals 9 FX 3U -CF-ADP User's Manual Associated Manuals Only the installation manual is packed together with the FX 3U -CF-ADP special adapter. For a detailed explanation of the FX 3U -CF-ADP special adapter, refer to this manual. For the hardware information and instructions on the PLC main unit, refer to the respective manuals.
Generic Names and A bbre viations Used in the Man ual 10 FX 3U -CF-ADP User's Manual Generic Names and Abbreviations Used in the Manual Generic name or abbre viat i on Description PLC FX 3U serie.
Generic Names and A bbre viations Used in the Man ual 11 FX 3U -CF-ADP User's Manual Generic name or abbre viat i on Description Manual FX 3U Hardware Editio n FX 3U Series Use r's Manual - .
Reading the Manua l 12 FX 3U -CF-ADP User's Manual Reading the Manual In this manual, the following formats are used for describing the common items. The above is different from the actual page, as it is provided for explanation only. This area shows the title of the chapter and the title of the section for the current page.
1 Introduction 1.1 Outline 13 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 1.
1 Introduction 1.3 Power and status LEDs 14 FX 3U -CF-ADP User's Manual 1.3 Power and status LEDs LED display Color Status Descript ion POWER Green OFF Power is not b eing suppl ie d from the ex ternal power supply (24V DC). ON Power is bein g supplie d fr om the exte rnal power supp ly (24V DC).
2 Specificatio n 15 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.
2 Specificatio n 2.1 General specificatio ns 16 FX 3U -CF-ADP User's Manual 2.1 General specifications For items not listed below, specifications are the same as the of the PLC main unit. For general specifications, refer to the manual of the PLC main unit.
2 Specificatio n 2.4 CF card AC CES S sw itch spe c if ic a t io n 17 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.
3 System Configuration 3.1 General configurati on 18 FX 3U -CF-ADP User's Manual 3. System Configuration 3.1 General configuration Component list Part name Model name Remarks CF card special adap te r FX 3U -CF-ADP An expa nsion board is req uired to conne ct the CF-ADP with the FX 3U /FX 3UC -32MT- LT PLCs.
3 System Configuration 3.2 Applicable PLC 19 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 3.
3 System Configuration 3.4 Assignment o f channels 20 FX 3U -CF-ADP User's Manual 2. FX 3UC (D, DSS) PLC 3.4 Assignment of channels The CF-ADP is handled in the same way as communication expansion boards and communication special adapters for PLCs.
3 System Configuration 3.4 Assignment o f channels 21 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.
4 Installation 22 FX 3U -CF-ADP User's Manual 4. Installation Only one CF-ADP unit can be connected to the left side of the main unit or special adapter. An expansion board is required to connect the CF-ADP with the FX 3U /FX 3UC -32MT-LT PLCs. For details, refer to the respective PLC manual.
4 Installation 4.1 CF-ADP Co nn e c tio n 23 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.
4 Installation 4.2 DIN rail mounting 24 FX 3U -CF-ADP User's Manual 4.2 DIN rail mounting The CF-ADP may be mounted on a 35mm (1.38") wide DIN46277 (DIN rail). Connect the CF-ADP to the PLC main unit before attaching the CF-ADP to a DIN rail.
4 Installation 4.3 Direct mounting 25 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.
4 Installation 4.4 Inserting an d Removal Procedures 26 FX 3U -CF-ADP User's Manual 4.4 Inserting and Removal Procedures 4.4.1 Inserting the CompactFl as h TM card The CompactFlash TM card can be inserted when the CF-ADP is power off.
4 Installation 4.4 Inserting an d Removal Procedures 27 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.
5 Wiring 28 FX 3U -CF-ADP User's Manual 5. Wiring DESIGN PRECAUTIONS • Make sure to includ e the followi ng safety circuits o utside the PLC to en sure safe sy stem operat ion even during exte rnal power supply problems or PLC failure. Otherwise, malfunctions may cause seriou s accidents.
5 Wiring 5.1 Which Power Supply Cable to Use 29 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 5.
5 Wiring 5.2 Power Supply Wiring 30 FX 3U -CF-ADP User's Manual 5.2 Power Supply Wiring 5.2.1 Power supply wiring *1. The expansion board is required when connecting with the FX 3UC -32MT-LT PLC. Power-on/off timing The CF-ADP power supply should be turned ON simultaneously with or before the power supply of the PLC main unit.
5 Wiring 5.4 Power OFF procedure 31 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 5.
5 Wiring 5.5 Connection o f the power supply cable 32 FX 3U -CF-ADP User's Manual 5.5 Connection of th e power supply cable The CF-ADP receives and supplies power through the built-in dedicated power connector.
6 Function s 6.1 Details o f functions 33 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 6.
6 Function s 6.2 Status informat ion 34 FX 3U -CF-ADP User's Manual 6.2 Status information The user can read the following status informat ion using applied instructions for the CF-ADP. • Detecting that a CompactFlash TM card is mounted. • Detecting that the CompactFlash TM card is full.
7 Before Programming 7.1 File format availa ble in the CF-ADP 35 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.
7 Before Programming 7.1 File format availa ble in the CF-ADP 36 FX 3U -CF-ADP User's Manual Contents of files in the "csv" format 7.1.2 Files create d by the user The contents of files created by the user should be same as files created by the CF-ADP (refer to Subsection 7.
7 Before Programming 7.1 File format availa ble in the CF-ADP 37 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.
7 Before Programming 7.1 File format availa ble in the CF-ADP 38 FX 3U -CF-ADP User's Manual 7.1.4 Data size calculation When calculating the data size, use the following fo rmula in accordance with the byte count shown in the table below.
7 Before Programming 7.1 File format availa ble in the CF-ADP 39 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.
7 Before Programming 7.1 File format availa ble in the CF-ADP 40 FX 3U -CF-ADP User's Manual 7.1.6 File ID Applied instructions for the CF-ADP use the file ID for specifying files. Accordingly, the file name saved in the CompactFlash TM card is associated with the file ID, and controlled by the ID table.
7 Before Programming 7.1 File format availa ble in the CF-ADP 41 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.
7 Before Programming 7.2 Directory structure 42 FX 3U -CF-ADP User's Manual 7.2 Directory structure The following directory is created inside the CompactFlash TM card. • In the case of a normal file The directory "FX3U_CFDATA." is created inside the CompactFlash TM card.
7 Before Programming 7.4 General Rules for Applied Instruct ions 43 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 7.
7 Before Programming 7.4 General Rules for Applied Instruct ions 44 FX 3U -CF-ADP User's Manual 7.4.2 Programming using "Ins truction execution complete " flag and "Instruction exe.
7 Before Programming 7.4 General Rules for Applied Instruct ions 45 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Befor.
8 CF-ADP Applied Instruc tions Explanatio n 8.1 CF-ADP Instructions types 46 FX 3U -CF-ADP User's Manual 8. CF-ADP Applied Instructions Explanation This chapter explains applied instructions for the CF-ADP. 8.1 CF-ADP Instructions types The PLC and the CF-ADP transfer data to each other using applied instructions for the CF-ADP.
8 CF-ADP Applied Instruc tions Explanatio n 8.2 Common Items in CF -ADP Instruction s 47 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 4.
8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 48 FX 3U -CF-ADP User's Manual 8.3 FNC 300 - FLCRT / File create•check Outline The FLCRT instruction creates a file inside the Compa ctFlash TM card mounted in the FX 3U -CF-ADP.
8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 49 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.3 FNC 300 - FLCRT / File create•check 50 FX 3U -CF-ADP User's Manual Caution When the file ID is "K0" 1) The CF-ADP can create up to 1000 files (within the CompactFlash TM card capacity). 2) The file name is set to "FILE0000.
8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 51 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 52 FX 3U -CF-ADP User's Manual 8.4.1 Detailed explanation of setting data Details of the setting data in the FLDEL instruction are as shown below.
8 CF-ADP Applied Instruc tions Explanatio n 8.4 FNC 301 - FLDEL / File delete•CF card format 53 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 54 FX 3U -CF-ADP User's Manual 8.5 FNC 302 - FLWR / Data write Outline The FLWR instruction writes data to the CompactFlash TM card or to the buffer inside the FX 3U -CF-ADP.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 55 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functi.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 56 FX 3U -CF-ADP User's Manual 8.5.1 Detailed explanation of setting data Details of the setting data in the FLWR instruction are as shown below. Cautions 1) The FLWR instruction is completed abnormally if a CompactFlash TM card is not mounted.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 57 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 58 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that D10 to D14 store values. This program does not describe such values. Specify the line position of the writing destination.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 59 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 60 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that D10 and D11 store values. This program does not describe such values. Specify the line position of the writing destination.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 61 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 62 FX 3U -CF-ADP User's Manual 1. When writing additi ona l data to a file • Set the data writing parameters as follows in all of a series of FLWR instructions.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 63 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functi.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 64 FX 3U -CF-ADP User's Manual D200 D8438 D201 D8437 FNC 12 MOV The error code is stored. The error code details are stored. FNC 12 MOV M0 RST M0 RST M8029 M8329 Specify the line position of the writing destination.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 65 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 2.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 66 FX 3U -CF-ADP User's Manual • Sequence program It is assumed that M15 stores bit data, M16 stores bit data, and R200 stores 16-bit decimal data. This program does not describe such values.
8 CF-ADP Applied Instruc tions Explanatio n 8.5 FNC 302 - FLWR / Data write 67 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functi.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 68 FX 3U -CF-ADP User's Manual 8.6 FNC 303 - FLRD / Data read Outline The FLRD instruction reads data from the CompactFlash TM card. 1. Instruction format 2. Set data 3. Appl icable devices Explanation of function and operation 1.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 69 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 70 FX 3U -CF-ADP User's Manual 8.6.2 Reading data of the same type from a file "m" data points of the same data type in one line are read as follows.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 71 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 72 FX 3U -CF-ADP User's Manual Program Exa mple • Explanation of operation When X000 turns ON, 4 data points of different types are r ead from the 1st column in Index 2 in the following file.
8 CF-ADP Applied Instruc tions Explanatio n 8.6 FNC 303 - FLRD / Data read 73 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functio.
8 CF-ADP Applied Instruc tions Explanatio n 8.7 FNC 304 - FLCMD / FX3U-CF-ADP command 74 FX 3U -CF-ADP User's Manual 8.7 FNC 304 - FLCMD / FX 3U -CF-ADP command Outline The FLCMD instruction gives instruction for operation to the FX 3U -CF-AD P. 1.
8 CF-ADP Applied Instruc tions Explanatio n 8.7 FNC 304 - FLCMD / FX3U-CF-ADP command 75 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 76 FX 3U -CF-ADP User's Manual 8.8 FNC 305 - FLSTRD / FX 3U -CF-ADP status read Outline The FLSTRD instruction reads the status (including t he error information and file information) of the FX 3U -CF- ADP.
8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 77 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 8.
8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 78 FX 3U -CF-ADP User's Manual • When is "K768 (H300)" The FLSTRD instruction reads the version information of the CF-ADP. • When is "K1024 (H400)" The FLSTRD instruction reads the error information (error flag).
8 CF-ADP Applied Instruc tions Explanatio n 8.8 FNC 305 - FLSTRD / FX3U-CF-ADP status read 79 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 W.
8 CF-ADP Applied Instruc tions Explanatio n 8.9 Contents of Related De vices 80 FX 3U -CF-ADP User's Manual 8.9 Contents of Related Devices The tables below show special auxiliary relays and special data registers used in CF-ADP instructions (FNC300 (FLCRT) to FNC305 (FLSTRD)).
9 Program Examples 9.1 System Configurati on 81 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.
9 Program Examples 9.2 Program Example 1 82 FX 3U -CF-ADP User's Manual 9.2 Program Example 1 9.2.1 Operation details • When X000 turns ON, the following file is created. If a file whose file ID is "1" already exists in the CompactFlash TM card, file creation and data name writing are aborted.
9 Program Examples 9.2 Program Example 1 83 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.
9 Program Examples 9.2 Program Example 1 84 FX 3U -CF-ADP User's Manual 9.2.4 Sequence Program This program example describes the sequence program for channel 1 (ch1). Rewrite the channel No. with the actual system configuration to be used. → For explanation of operations, refer to Subsection 9.
9 Program Examples 9.2 Program Example 1 85 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting *1.
9 Program Examples 9.2 Program Example 1 86 FX 3U -CF-ADP User's Manual Specify the data writing type. D21 K1 D22 K1 FNC 12 MOV Specify the line position of the writing destination. Number of written data points. Writing destination. Specify the data column position in the writing destination.
9 Program Examples 9.2 Program Example 1 87 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting The buffered data forcible writing execution counter is set to "0".
9 Program Examples 9.2 Program Example 1 88 FX 3U -CF-ADP User's Manual File delete. M8405 CF card is mounted M3 M8404 CF-ADP unit ready Remains ON while the 32- bit decimal type file is being deleted Remains ON while the 32-bit decimal type file is being deleted.
9 Program Examples 9.3 Program Example 2 89 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.
9 Program Examples 9.3 Program Example 2 90 FX 3U -CF-ADP User's Manual X007 Deletes the mixed type f ile. M4 Remains O N whil e a mixed type file is be in g cr eated. M5 Remains ON while data is b eing written to the mixed typ e file. M6 Remains ON while data is being read from the mixed ty pe file.
9 Program Examples 9.3 Program Example 2 91 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.
9 Program Examples 9.3 Program Example 2 92 FX 3U -CF-ADP User's Manual *1. When is "K7" or "K8", 00H, which indicates the end of the string, must be added to the end of the character string. In addition, in sequence example, it is written in such a way that "00H" is placed in a blank area of a characte r string.
9 Program Examples 9.3 Program Example 2 93 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting Specify the line position of the writing destination.
9 Program Examples 9.3 Program Example 2 94 FX 3U -CF-ADP User's Manual From previous page From previous page To next page To next page Number of written data points. Data writing. Specify the data writing type. D23 K1 FNC 12 MOV FNC302 FLWR K0 D20 K2 FNC 12 MOV R0 D20 D30 K1 Number of written data points.
9 Program Examples 9.3 Program Example 2 95 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting Specify the line position from which data is read.
9 Program Examples 9.3 Program Example 2 96 FX 3U -CF-ADP User's Manual Specify the data reading type. D40 K6 FNC 12 MOV D43 K1 FNC 12 MOV Number of read data points. Data reading. FNC303 FLRD K0 D40 R140 D50 K1 Specify the data reading type. D40 K7 FNC 12 MOV D43 K1 FNC 12 MOV Number of read data points.
9 Program Examples 9.4 Program Example 3 97 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 9.
9 Program Examples 9.4 Program Example 3 98 FX 3U -CF-ADP User's Manual 9.4.3 Sequence Program This program example describes the sequence program for channel 1 (ch1). Rewrite the channel No. with the actual system configuration to be used. → For explanation of operations, refer to Subsection 9.
10 Troubl e shooting 99 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10.
10 Troubl e shooting 100 FX 3U -CF-ADP User's Manual STARTUP AND MAINTEN ANCE PRECAUTIONS • Make sure to connect the batter y correctly. Do not ch arge, disa ssemble, hea t, short-cir cuit, or expose the battery to f ire. Doing so may rup ture or igni te it.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 101 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 102 FX 3U -CF-ADP User's Manual 10.1.3 Error Code List and Action The list below shows error codes and corrective actions. 1. Error code list Error code Error definit io n Error correcti ve action 1 Parity, Fram ing, Overrun error Check the con nection to the CF- ADP.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 103 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programmi.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 104 FX 3U -CF-ADP User's Manual 503 ID table read error The file management in formation was not able to be read from the CompactFlash TM card. When readin g or deletin g a file, co nfirm that the target f ile exists.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 105 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programmi.
10 Troubl e shooting 10.1 Troubleshooti ng procedure 106 FX 3U -CF-ADP User's Manual 909 Buffered data writing error to CompactFl ash TM card Buffered d ata was not abl e to be written to the Compa ctFlash TM card. Check whethe r the CompactFla sh TM card is mounted correctly , and whether it has sufficient f ree space.
10 Troubl e shooting 10.2 Diagnostics o n the PLC Main Unit 107 FX 3U -CF-ADP User's Manual 1 Introduction 2 S pecification 3 System Configuration 4 Installation 5 Wiri ng 6 Functions 7 Before Programming 8 CF-ADP Applied Instructions Explanation 9 Program Examples 10 T roubl eshooting 10.
10 Troubl e shooting 10.2 Diagnostics o n the PLC Main Unit 108 FX 3U -CF-ADP User's Manual 10.2.3 ERROR(ERR) LED [on/flashing/off] The table below describes details for the LED statuses. Status PLC Stat us Error correc tive action ON A watchdog time r error may ha ve occurred, or the hard ware of the PLC may b e damaged.
Appendix A: Relate d Devices Appendix A-1 Related Devic e List 109 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix A: Related Devices Appendix A-1 Related Device List The tables below show special auxiliary relays and special data registers used in CF-ADP instructions (FNC300 (FLCRT) to FNC305 (FLSTRD)).
Appendix A: Relate d Devices Appendix A-2 Details of related devices 110 FX 3U -CF-ADP User's Manual Appendix A-2 Details of related devices This section explains devices used during CF-ADP. Appendix A-2-1 Instruction ex ecution complete [M8029] When execution of CF-ADP instructions is completed, this device turns ON.
Appendix A: Relate d Devices Appendix A-2 Details of related devices 111 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix A-2-5 CF card mount status [M8405, M8425] These devices indicate the CompactFlash TM card status.
Appendix A: Relate d Devices Appendix A-2 Details of related devices 112 FX 3U -CF-ADP User's Manual Appendix A-2-10 Step number of an instruction for the CF-ADP where an error has occurred [D8415, D8414] [D8435, D8434] These devices store the step number of an instruction for the CF-ADP where an error has occurred.
Appendix B: V ersi on Info rmation Appendix B-1 Version information 113 FX 3U -CF-ADP User's Manual A Relat ed Dev ices B V ersion Information Appendix B: Version Information Appendix B-1 Version information Appendix B-1-1 Version check method 1.
Appendix B: V ersi on Info rmation Appendix B-1 Version information 114 FX 3U -CF-ADP User's Manual MEMO.
115 FX 3U -CF-ADP User's Manual Warranty Warranty Please confirm the following product warra nty details before using this product. 1. Gratis Warranty Term and Gratis Warran ty Range If any fault.
116 FX 3U -CF-ADP User's Manual Revised History Revised History Date Revision Desc ription 6/2009 A First Edition.
.
HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN HIMEJI WORKS: 840, CHIYO DA CHO, HIMEJI, JAPAN JY997D35401A (MEE) Effective June 2009 Specifications are subject to chang e withou t notice.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Mitsubishi Electronics FX3U-CF-ADP è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Mitsubishi Electronics FX3U-CF-ADP - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Mitsubishi Electronics FX3U-CF-ADP imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Mitsubishi Electronics FX3U-CF-ADP ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Mitsubishi Electronics FX3U-CF-ADP, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Mitsubishi Electronics FX3U-CF-ADP.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Mitsubishi Electronics FX3U-CF-ADP. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Mitsubishi Electronics FX3U-CF-ADP insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.