Manuale d’uso / di manutenzione del prodotto 926042 del fabbricante Ariens
Vai alla pagina of 26
Quick St art Guide Pr o - T r ack 28 (92604 2 s /n 75000 & up) • Step 1: Unfold Handlebar • Step 2: Install D is char ge Chute • Step 3: Install C hute Contr ol Assembly • Step 4: Install .
St ep One: Unf old Handlebar 1. Remove the lower and loosen the upper hardw are on the handlebar assembly . 2. Loosen the hard war e on the shift rod. 3. Put the speed selector lever in the second reverse position. 4. Rotate the handlebar into operating position.
St ep T wo: Inst all Discharg e C hute 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardw are from auger housi ng. 3. Install discharge chute over opening in the auger housing. Finger tighten the mounting hardwar e removed above.
St ep Three: Ins tall Chute Con trol Assembly 1. Remove the gear cover from top of chute pedesta l. 2. Release the lock teeth on the gear assembly with your finger and rotate the discharge chute so it points straight ahead. NOTE : Make sure alignment markers are lined up when discharg e chute is pointing straight ahead .
St ep Three: Ins tall Chute Con trol Assembly Cont. 3. Remove the rubber gromm et from the control panel. 4. Make sure the chute control cable is routed betw een the lower handlebar and the bottom of the control panel, insert contro l assembly into slot in control panel from below and install assembly into nylon bushing in control panel.
St ep Four: Inst all Discharg e Chute R od NOTE : T o ensure the discharge chute follows its full range of travel , make sure the control lever is centered i n the slot and pointing straight up before i nstalling the chute rod.
St ep F our: Ins t all Dischar ge Chut e Rod Con t. 4. Hook the chute contro l cable onto the chute rod . IMPORT ANT : The chute control cable hook will prevent the cable from contacting the engine or muf fl er guard. Make sure the cable stays connected whi le unit is in operation.
St ep Five: Inst all R e mote Deflect or Control Cable 1. Connect the barr el cable end to the chute defl ect or cable anchor before clipping t he cable to the discharge chute cable bracket . 2. Route deflector r emote cable along the lef t side of the chute pedestal.
St ep Six: Check Functio n of Dual Handle In t erlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch s hould remain engaged until traction clutch lev er is released, then both clutches must disengage.
St ep Sev en: Check T r ack T ension Check tracking of unit with the dif ferential locked, and tension of tracks (see T rack T ension Adjustment in Owners Manual.
St ep Eight: Adjus t Skid Shoes IMPORT ANT : Skid shoes should be adjus ted as conditions require. Allow 1/8 in. (3mm) between scraper blade and hard smooth surfac es. Allow 7/8 in. (22 mm) betw een scraper blade and uneven or grav el surfaces . (S ee Skid Shoes in O wners Manual) .
Check oil level in auger gearcase (see Check Auger Gearcase in Owner s Manual). St ep Nine: Check Aug er Gear case Oil.
IMPORT ANT : T he engine is shipped with oil in crankcase. Refer t o Engine Manual for detailed instructions. St ep T en: Check Engine Cr ank case Oil.
Fill fuel tank. DO NO T OVERFILL! See FILLING FUEL T ANK in Owners Manual. St ep Elev en: Fill Eng ine F uel T ank.
St ep T w elv e: St arting the Engine.
St arting Engine / St ep A: Thr ottle Move the throttle control lever to the fast position. Operate the engine with the thrott le control lever in the fast position.
St arting Engine / Step B : Fuel V alv e T urn the fuel shut - of f valve to the ON position..
St arting Engine / Step C : Ke y Insert the key and turn to the ON/ST AR T position..
St arting Engine / Step D : Chok e T urn the choke control knob to the choke position. NOTE: Choke is usually unnecessary when restarting a warm engine.
St arting Engine / Step E : Prime Push the primer two times. Be sure to cover vent hole on primer bulb. NOTE: Priming is usually unnecessary when restarting a warm engine.
St arting Engine / Step F : (Manual St art) Firmly hold the starter cord handle. Pull the starter cord han dle slowly u nt i l re s is tance is felt, then pull rapidly . NOTE : If the engine does not start a fter repeated attempts , go to BRIGGSandSTRA TTON.
St arting Engine / St ep F : (Electric St art) First conn ect the extension cord to th e power cord rec eptacle and then into a wall receptacle. If an additional ext ension cord is requir ed, make sure it is a 3 - wire grounded extens ion cord.
St arting Engine / St ep G: (Electric St art) Depress the push button. After you start the engine, first disconnect the extension cord from the wall receptacle and then from the power cord receptacle.
St arting Engine / Step H: W arm up Allow the engine to warm up for several minutes. Then, slowly move the choke control knob to the run position..
St ep Thirt een: St opping the Engine T urn the key t o the off position or move throttle control lever to slow and then to the stop position (completely right). Remove the key . Keep away from reach of children. After engine stops, turn the fuel s hut - of f valve to the closed (vertical) position.
Additional R esour ces • R ef er t o Owner s Manua l and Engin e Manual • Cont act Ariens Com pan y www .ariens.c om Phone: 920 -756-4688 E- mail: inf o@ariens.c om • F or issues concerning engine, pl ease con tact Brig g s and Str at t on www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ariens 926042 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ariens 926042 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ariens 926042 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ariens 926042 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ariens 926042, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ariens 926042.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ariens 926042. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ariens 926042 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
