Manuale d’uso / di manutenzione del prodotto 924127 ST11528DLE del fabbricante Ariens
Vai alla pagina of 32
Owner/Operator Man ual Models 924124 – ST926DLE 924125 – ST1 1528LE 924126 – ST1 1526D LE 924127 – ST1 1528D LE 924128 – ST1332L E 924335 – ST926DLE 924336 – ST1 1526D LE 924337 – ST1 .
2 Ariens Company 655 West Ryan S treet P .O. B ox 157 Brillion, Wiscons in 541 10-0157 USA T elephone (920) 756-2141 Facsimile (920) 756-2407 EC DECLARA TION OF CONFORMITY ISSUED BY TH E MANUF ACTURER.
3 CE Sound and Vibra tion – Niveau sonore et vibration CE – CE-Geräuschpeg el und V ibrations werte – Li vello sonoro e vi b r azioni CE – Sonido y vibración CE – CE-lydnivå o g Vibrasj o.
GB - 4 Safe ty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Controls a nd Fe a t ure s . . . . . . . . . . . . . . . 13 Oper a t ion . . . . . . . . . . . . . . . . .
GB - 5 DELIVER Y Customer Note: I f you have purchased this product without complete assembly and instruction by your retailer , it is your responsibility to: 1. Read and underst and all assembly instructions in this manual. If you do not understand or have difficulty following the instructions, contact your near est Ariens Dealer for assistance.
GB - 6 SAFETY DECALS AND LOCATIONS AL WA YS replace missing or damaged Safety Decals. Refer to figure below for Safety Decal locations. 1. DANGER! 2. W ARNING! 3. DANGER! SAFE T Y R UL ES Read, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operating.
GB - 7 Keep area of operation clear of all t oys, pets, and debris. Thrown objects can cause injury . Check for w eak spots on dock s, ramps or floors. Avoid uneven work areas and rough terrain. S tay alert for hidden hazards. Avoid uneven and rough terrain.
GB - 8 Before cleaning, removing clogs or making any inspections, repairs, etc.: disengag e clutch(es), stop unit and engine, remo ve key , allow moving par ts to stop. Al low hot part s t o cool. Run unit a few minutes aft er clearing snow to prevent freeze-up of attachment.
GB - 9 • In case of internal c ontact, DO NOT induce vomiting! Before tipping unit up onto housing, remov e fuel so no spills will occur and remove battery . Ensure unit is secure and will not tip ov er during maintenance. AL WA YS keep protective structures , guards, and panels in good repair , in place and securely fastened.
GB - 10 Inst all D ischarge C hute (9 24124-128, 335-338, 516) Figure 5. 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge chute over opening in the auger housing and secure pedestal to auger housing with hardware removed in step 2.
GB - 1 1 Inst all D ischarge C hute (9 24517) 1. Remove chute mo tor cover from chu te motor (Figure 7). 2. T urn the chute gear until the solid pin i s towards the rear of the unit and a threaded stud aligns with the c hute motor (Figure 7). 3. Remove the six (6) nuts and two half rings (Figure 7).
GB - 12 Connec t Battery (92451 6, 517 ) 1. Remove w ing nuts from battery c over . 2. Inst all wire lead to bat tery terminal. 3. Install battery cover and tighten wing nuts. Deflector Remote 1. Remov e e-ring and flat washer from s tud on discharge chute.
GB - 13 1. T raction Drive Clutch Lever 2. Oil Fill/Di pstick 3. Muffler Guard 4. Belt Cover 5. Discharge Chute Deflector 6. Discharge Chute 7. Electric Chute Motor (924517) 8. Impeller 9. Clean-out T ool 10. Auger Gearcase 1 1. Scraper Blade 12. Auger 13.
GB - 14 CONTROLS AND FEA TURES See Figure 1 1 for all Controls and Features locations. Dual Handle Interlock When Attachment Clutch and t hen T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released. T o stop attachment, release T raction Drive Clutch and both cl utches will disengage.
GB - 15 Choke Control Knob 1. Choke C losed position: chokes off ai r to engine f or easier start. 2. Choke Open position: allows for normal operation. IMPORT ANT : Gradually open choke after engine st art s. Throttle The throttle controls the engine speed.
GB - 16 Differenti al Lock (924124, 1 26, 127, 335, 336, 337, 516 , 517) Differential Lock knob is located on the Left Wheel Hub . With differential locked power is applied equally to both wheels. T o engage differential lock: • Pull and turn knob to LOCKED (1) position and releas e (knob will snap in place when positioned correctly).
GB - 17 FILLING FUEL T ANK Fuel Shut-Off V alve IMPORT ANT : The f uel shut-off valve MUST be in the closed position prior t o transporting the unit. The fuel shut-off valve has t wo positions: • Closed Position: Use this position to service, transport, or store the unit.
GB - 18 NOTE: When temperature is below -15° F (-26° C) additional priming may be needed. 4. If engine is cold, apply choke. See E ngine Manual for detail ed instructions. NOTE: A warm engine requires less choking than a cold engine. 5. Set throttle to proper start ing position.
GB - 19 1. Select Speed Control position and direction. 2. Engage Attachment Clutch - Right Hand Lever . 3. Engage Traction Drive Clutch - Left Hand Lever . IMPORT ANT : DO NOT overload unit capacity by attempting to c lear snow at t oo fast a rate. Use slow speed to clear deep or hard p acked snow .
GB - 20 CHECK DUAL HANDLE IN TERL OC K Without the engine running, pres s down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch should remain engaged until traction cl utch lever is released, then both clutches must disengage.
GB - 21 CLEAN BATT ERY (92451 6, 517) IMPORT ANT : Battery is maintenance-f ree. Do not t amper with or attempt to open battery . See Service and A djustments for charging procedures. Te r m i n a l s Keep battery and its terminals clean. IMPORT ANT : Remove battery from unit before cleaning.
GB - 22 DISCHARGE CHUTE If chute does not st ay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on s pring (Figure 17). RUNNERS Runners should be adjusted (Figure 18) as conditions require. 1. Position unit on a har d, flat, smooth level surface.
GB - 23 SCRAPER BLADE IMPORT ANT : Damage to auger/impeller housing will result if blade wears down too far . Scraper blade is adjustable to compensate for wear . T o adjust scraper blade: 1. T ip unit back onto handlebar , support housing and loosen nuts ret aining blade.
GB - 24 ATT ACHMENT CLUTCH/BR AKE ADJUSTMENT (Figures 21 and 22) 1. Remove belt cover . 2. Check belt alignment ( Figure 24). Engine sheave and attachment pulley must align vertically . Also, belt must be centered in the idler pulley . T o align, move attachment pulley: a.
GB - 25 T RACTION DRIVE CLUTCH ADJUSTMENT If drive slip s, adjust traction clutch to compensate for friction disc wear . T o adjust traction clutch: 1.
GB - 26 8. Remove attachment drive belt f rom attachment pulley (hold brake aw ay from belt). Inst all ne w att achment d rive belt: 1. Place new attachment bel t onto attachment pulley . 2. T ip housing and frame back t ogether and secure with cap s crews.
GB - 27 5. Release traction clutch lever, shift to third (3) position, and rem ove friction disc. 6. Secure new friction disc on hub with five cap screws and torque cap screws to 8-10 lbf-ft (10,6-13, 3 N•m). 7. Replace bottom cover . 8. Adjust traction drive clutch (see T rac tion Drive Clutch Adjustment ).
GB - 28 T ROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ st art. 1. Fuel tank i s empty . 2. Fuel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Switch not in run position. 5. Ignition switch starter circuit not functioning.
GB - 29 SPECIFI CATIONS Model Numbe r 924124 924125 924126 924127 924128 Description ST926DLE ST1 1528 LE ST1 1526 DLE ST1 15 28DLE ST1332L E Engine - T ecumseh OH318SA OH318SA OH358SA Power Max - HP (kW) 9.0 (6.71) 1 1.5 (8.6) 13.0 (9.7) Fast Id le S peed - RPM (min -1 ) 3600 ± 150 Displacement - in.
GB - 30 SPECIFI CATIONS Model Numbe r 924335 924336 924337 924338 924516 924517 Description ST926 DLE S T1 1526D LE ST1 1528D LE ST133 2LE ST13 32DLE ST1336DL E Engine - T ecumseh OH318SA OH318SA OH358SA OH358SA Power Max - HP (kW) 9.0 (6.71) 1 1.5 (8.
GB - 31 3-Y ear Limited Sno-Thr o W arranty Ariens Company warr ants to the original purchaser that consumer products manuf actured by Ariens Company will be free from def ects in material and workman.
Ariens Company 655 West Ryan Street P .O. Box 157 Brillion, WI 541 10-0157 920-756-2141 Fax 920-756-2407 www .ariens.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ariens 924127 ST11528DLE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ariens 924127 ST11528DLE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ariens 924127 ST11528DLE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ariens 924127 ST11528DLE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ariens 924127 ST11528DLE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ariens 924127 ST11528DLE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ariens 924127 ST11528DLE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ariens 924127 ST11528DLE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
