Manuale d’uso / di manutenzione del prodotto 921032 del fabbricante Ariens
Vai alla pagina of 27
Quick St art Guide Delux e 30 (921 032 s/n 101 & up) • Step 1: Assemble Handlebars • Step 2: Connect Headlight Wire Harness • Step 3: Install Discharge Chute • Step 4: Install Discharge Ch.
Step On e: Assemble Handlebar s (Unf old Lower Handlebar) IMPORT A NT : Be sure to block wheels or secure unit so it does not move during assembly . 1. Rotate lower handlebar out from unit so low er handlebar mounting holes align w ith mounting holes on the unit f rame.
Step On e: Assemble Handlebar s (A t tach Upper Hand lebar Assembly) 1. Attach upper handlebar assembly to lower handlebar using two sets of the handleb ar hardware. One set to att ach each side of the handlebar s. NOTE: DO NOT tighten hardw are. Allow upper handlebar assembly to hang from the lower handlebar s for the nex t st ep.
Step On e: Assemble Handlebar s (A t tach Con tr ol Cables) 1. Hook spring end of attachme nt c ontrol cable to the clutch arm. 2. Hook spring end of the traction c ontrol cable to the cable eyelet on back of frame. NOTE: Make sure cable remains in groove of pulley .
Step On e: Assemble Handlebar s (Unf old Upper Handlebar) Assembly) 1. Rotate handlebar into operating position. NOTE: Be careful not to damage cable spring hooks when rotating handlebar upward. 2. Install the remaining handlebar hardware attaching the upper handlebar as sembly to the low er handlebar .
Step T wo: Connect Headligh t Wir e Harness NOTE: The headlight w ire harness comes attached to the upper handlebar as sembly . 1. Route the wire harness along the interior of the right side handlebar . 2. Connect to the engine elec trical plug. 3. Press cable anc hor into mounting hole in the frame near the engine electrical plug.
Step Thr ee: Ins t all Discharg e Chut e 1. Grease underside of discharge chute ring (if not already greased). 2. Remov e mounting hardware from auger housing. 3. Install discharge c hute over opening in the auger housing. Finger tighten the mounting hardware remov ed above.
Step F our: Ins t all Discharg e Chut e Cr ank 1. Remov e the gear cov er from top of chute pedest al. 2. Insert the short end of the c hute crank into the hole in the front of the control panel. NOTE: Be careful not to damage ny lon bushing when attaching crank to the dash.
Step Fiv e: Inst all Remot e Deflect or Con trol Cable NOTE: Connect the barrel cable end to the chute deflector cable anchor before clipping the cable to the discharge chute cable bracket. 1. Route deflector remote cable along the left side of the chute pedestal.
Step Six: Ins t all Skid Shoes 1. Remove hardware from skid shoes. 2. Install hardware through blower housing and skid shoe as shown. 3. Adjust skid shoes, see Skid Shoes in Owners Manual.
St ep Sev en: Check Function of Dual Handle In terlock Without the en gine running , press dow n (engage ) both clu tch levers. Relea se attachment clutch lever . Attachment clu tch should remain engage d until traction clutch lever is released , then both clutches must d isenga ge.
St ep Eigh t: Check Tir e Pr essur e Check tire pressu re and adjust to the pressure listed on tire sidew all..
Check oil le vel in auger gearcase (see Check Auger Gearcase in Ow ners Manual). St ep Nine: Check Aug er Gear case Oil.
IMPORT A NT : The engin e is shipped with 5W-30 oil in crankcase. Refer to engine manual for detailed instructions. St ep T en: Check Engine Cr ank case Oil (Ariens AX).
Fill fuel tank. DO N OT OVERFILL! See FILLING FUEL T ANK in Ow ners Manual. St ep T welv e: Fill Engine Fuel T ank (Ariens AX).
St ep Thirt een: St arting the Engine (Arie ns AX).
St arting Engine / Step A: Chok e T urn throttle al l the way up. T urn choke ON..
St arting Engine / Step B: R ock er Swit ch Push rocker switch to RUN position..
St arting Engine / Step C: Fuel Shut Off V alv e T urn fuel petcock to ON position..
St arting Engine / Step D: K ey Install Safety K ey Switch. Insert ignition key into slot but DO NOT turn the key . Be sure ignit ion key snaps into place.
St arting Engine / Step E: Prime Prime sy stem: 3 primes maxi mum. DO NOT over prime system. Make sure to cover the v ent hole on primer bulb before the primer bulb is compressed. Hold the primer bulb in the compressed pos ition for one full second each time you press it.
St arting Engine / Step F: (Manual St art) Grasp rope handle. Pull slowly until resistance is felt, then pull rope firmly and quickly to start engine and avoid kickback.
St arting Engine / Step F: (Electric St art) Use a 3-wire ex tension cord and plug cord into starter motor adaptor first. Then plug cord into wall receptacle. Use appropriately siz ed extension cord (10A WG or larger) to prevent damage to electric starter .
St arting Engine / Step G: (Electric St art) Press and hold starter button. Note : Do not hol d the electric starter button down for more than 5 seconds.
St arting Engine / Step H: W arm up Allow the engine to warm up for 1- 2 minutes, move the choke control to the CHOKE OFF position..
St ep F ourt een: St opping the Engine (Ariens AX) Under normal condition s: 1. T urn throttle dow n. 2. Push rocke r sw itch to STOP position. 3. Pull safety key OUT . T o s top engine in a n emergency , fli p the Rocker Sw itch to the ST OP p osition, OR Pull Safety Key from Engine.
Additional R eso ur ces • R ef er to O wner s Manual and Engine Manual • Con t ac t Ariens Compan y www .ariens.com Phone: 920- 756 - 4688 E-mail: inf o@ariens.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ariens 921032 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ariens 921032 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ariens 921032 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ariens 921032 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ariens 921032, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ariens 921032.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ariens 921032. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ariens 921032 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
