Manuale d’uso / di manutenzione del prodotto 3545 del fabbricante Miller Electric
Vai alla pagina of 28
Processes OM-1216 205 917D 2006 − 09 Description MIG (GMAW) W elding Wire Feeder Spool Gun Spoolmat e 303 5 And 3545 Spoolma te 303 5 Spoolma te 354 5 ™ File: Wire Feeder V isit our website at www.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
OM-1216 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown i n the adjoining symbols.
OM-1216 Page 2 Arc rays from the w elding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.
OM-1216 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-1216 Page 4 1-5. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www .
OM-1216 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION som _3/05 Y A vertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-1216 Page 6 Le rayonnement de l’arc du procédé de soudage génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provo- quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage.
OM-1216 Page 7 2-3 . Da ngers supplém entair es en relation avec l’installa tion, le f onc tionneme nt et l a maintena nce Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur , au-dessus ou à proximité de surfaces inflammables.
OM-1216 Page 8 2-5. Princi pales nor mes de sécurit é Safety in W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www .
OM-1216 Page 9 SECTION 3 − INST ALLA TION 3-1. Specifications For Spoolmate 3035 Wire Diameter Range Approximate Wire Feed Range Cooling Method Maximum Spool Size W eld Circuit Rating Overall Dimensions W eight .023 Thru .035 in (0.8 Thru 0.9 mm) Aluminum Wire .
OM-1216 Page 10 3-3. Connecting Spool Gun T o Millermatic 210 3 802 998-C 1 2 4 Rear Panel 5 6 1 Barbed Fitting . If spool gun gas hose is equipped with a pre-installed barbed fitting, cut off fitting from end of hose. Connect spool gun gas hose to barbed fitting.
OM-1216 Page 1 1 3-4. Installing Wire Spool And Threading W elding Wire Ref. 801 891-B T ools Needed: 1 Thumb Screw 2 Spool Cover Remove thumb screw and spool cover . 3 Hub T ension Nut 4 Wire Spool Install spool so wire feeds from top. Turn hub tension nut just so a slight drag is felt on the wire spool.
OM-1216 Page 12 3-5. Removing Existing Barrel And Installing Contact Adapter 802 379-B 1 Base Nut Location Remove base nut from handle. 2 Handle Section Remove handle section from gun. 3 Drive Roll Assemblies Remove drive roll assemblies. 4 Nut Remove nut from barrel.
OM-1216 Page 13 SECTION 4 − OPERA TION 4-1. Controls sb5.1* 6/92 − S-0621-C / 804 386-A . Spool Gun On/Off switch in Millermatic 185 Hobart IronMan 210 or IronMan 250 must b e i n O n position for spool gun operation (see Field Kit 207 642 instructions).
OM-1216 Page 14 5-2. Changing Drive Rolls 801 893-B T ools Needed: Y T urn Off power at welding power source first. 1 Drive Roll Cover Remove cover . Changing Push Roll: T o remove push roll: 2 Push Roll Screw 3 W asher 4 Push Roll Remove screw and washer , and lift out drive roll.
OM-1216 Page 15 5-3. Changing Liner Ref. 801 891-B T ools Needed: Y T urn Off power at welding power source first. 1 Nozzle 2 Contact Tip 3 Liner Remove and replace liner . Reinstall parts as shown. 1 2 3 5-4. T roubleshooting T rouble Remedy Gun tube assembly loose.
OM-1214 Page 16 Notes.
OM-1216 Page 17 SECTION 6 − ELECTRICAL DIAGRAMS Figure 6-1. Circuit Diagram 186 451.
OM-1216 Page 18 SECTION 7 − P ARTS LIST . Hardware is common and not available unless listed. 801 900-F 3 2 32 28 31 33 29 19 30 18 17 27 22 21 20 14 11 10 4 9 8 7 6 5 4 2 1 40 41 42 43 39 38 36 37 35 34 23 26 25 24 13 15 16 12 Figure 7-1.
OM-1216 Page 19 Quantity Description Part No. Dia. Mkgs. Item No. Figure 7-1. Complete Assembly for Spoolmate 3035 1 PB1 186 416 TRIGGER SWITCH 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1216 Page 20 . Hardware is common and not available unless listed. 802 577-C 3 2 32 36 28 31 33 37 34 41 42 43 29 19 35 38 39 40 30 26 25 27 22 21 20 11 10 4 9 8 7 6 5 4 23 24 14 13 15 16 12 18 17 2 1 Figure 7-2.
OM-1216 Page 21 Quantity Description Part No. Dia. Mkgs. Item No. Figure 7-2. Complete Assembly For Spoolmate 3545 1 PB1 186 416 TRIGGER SWITCH 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1216 Page 22 204 161 1 2 3 4 5 6 Figure 7-3. Spoolmate Optional Hose & Cables Extension Kit Description Part No. 194 996 Item No. Figure 7-3. Spoolmate Hose & Cables Extension Kit Quantity 1 172 171 FITTING, hose, brass 1 . . . . . . . . . .
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2006 − 01 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.
PRINTED IN USA © 2006 Miller Electric Mfg. Co. 2006 − 01 Miller Elect ric Mfg. Co. An Illinois T ool W orks Compan y 1635 West Spenc er St reet Applet on, W I 54914 USA International He adquarters .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miller Electric 3545 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miller Electric 3545 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miller Electric 3545 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miller Electric 3545 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miller Electric 3545, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miller Electric 3545.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miller Electric 3545. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miller Electric 3545 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
