Manuale d’uso / di manutenzione del prodotto W 4446 WPS del fabbricante Miele
Vai alla pagina of 72
Operating instructions for Washing machine W 4446 WPS To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Caring for our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating the washing machine . .
Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 The correct detergent ..............................................3 5 Water softener .........................................
The Miele Waterproof system ........................................5 7 Connection to the water supply .......................................5 8 Connection to the drainage system ....................................6 0 Electrical connection U.K. ....
This washing machine conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the washing machine, please read these instructions carefully before using it for the first time.
Technical safety ~ Before setting up the washing machine, check it for any externally visible damage. Do not install or use a damaged washing machine. ~ Before connecting the washing machine, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply.
~ This washing machine may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ Do not make any alterations to the washing machine, unless authorised to do so by Miele.
~ Textiles which have been pre-treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine. ~ Never use solvent based cleaning agents, e.g. those containing benzene, in this machine, as this may result in damage to component parts and create toxic fumes.
Control panel a Programme buttons For selecting a washing programme. b Display with Menu buttons See the next page for more information. c PC / Optical interface This is used by service technicians to run diagnostic checks on your machine and can also be used to update programming data in the future.
Display The display is used for the following: Selecting and displaying settings – Temperature – Spin speed – Soak duration – Delay start – Cancelling a programme – Safety lock – Estimat.
Menu buttons Various settings are made via the Menu buttons. They are used to alter or confirm the value displayed above the vertical line. To alter a setting: Cottons Duration: 1:49 h 60°C 1600 rpm Pressing the left hand Menu button under 60°C alters the temperature and pressing the right hand Menu button under 1600 rpm alters the spin speed.
Before using the machine for the first time ensure that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened to prevent the risk of water leaks during use.
Reminder to remove transit bars To avoid the risk of damage, the transit bars must be removed before the machine is used for the first time. See "Installation and connection" for instructions on how to do this. ^ After removing the transit bars (if this has not already been done by your fitter) press the right hand Menu button under OK .
Energy and water consumption – Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using. – Use the Automatic and Express programmes for small loads.
Brief instructions The headings numbered A , B , C ,... show the operating sequence and can be used as brief instructions. A Sort the laundry ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.
B Switch on the washing machine The interior drum lighting will come on. All the programme indicator lights will come on, and the display will ask you to select a programme.
^ Select any extra options by pressing the appropriate button. The relevant indicator light will come on to show which extra option has been selected. ^ Press the Further extras button to select the following extra options (depending on the programme selected): Soak , Rinse hold and Extra rinse .
F Add detergent When the door is closed, the load size indicator will be replaced with the detergent percentage display. Detergent 75% A Back A The percentage shown relates to the amount of detergent recommended by the manufacturer on the packaging.
^ Pull out the detergent drawer and add detergent to the compartments as follows: i Detergent for the pre-wash (divide the total recommended amount as follows: add 1 / 3 to compartment i and 2 / 3 to compartment j ) This compartment i is also used for starch formulations when starching separately.
I Remove the laundry when the programme has finished In the anti-crease phase after the programme has finished, the following will appear alternately in the display: Cottons Anti-crease 60°C 1600 rpm and : Programme finished Unload the drum before switching off ^ Press the Door button to open the drum door.
Short For light to nomal soiling with no visible staining. The duration of the main wash is reduced. Water plus The water level in the main wash and the rinses will be increased if the Water plus option is selected. Pre-wash For laundry with large amounts of dirt e.
Final spin speed Programme rpm Cottons 1600 Minimum iron 1200 Delicates 600 Woollens 1200 Automatic 1200 Shirts 600 Express 1600 Denim 900 Hygiene 1600 Dark garments 1200 Curtains 600 Pillows 1200 Sil.
With delay start you can choose when you want the programme to end. The start of a programme can be delayed from 30 minutes up to a maximum of 24 hours, allowing you to make use of night-time economy electricity rates, for example. The current time of day needs to have been set for delay start to work correctly.
To alter delay start You can subsequently select a later programme end time if you wish. ^ Press the Delay start button. Delay start 9:05 from 16:16 to 18:00 Change OK ^ Use the left hand Menu button under Change to alter the time you want the programme to end at.
Cottons 98E76 * 30°C to 95°C Max. load 6.0 kg Fabric Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, underwear, T-shirts etc. Extra options Pre-wash, Soak, Short, Water plus, Rinse hold, Extra rinse Note for test institutes: Short programme: 3.
Shirts cold to 60°C Max. load 2.0 kg Notes – Pre-treat collars and cuffs if necessary. – Wash silk garments in the Silks programme. Extra options Short, Water plus, Rinse hold Express 76 * cold to 40°C Max. load 3.0 kg Fabric Small loads of items which require freshening up and which can be washed in a Cottons programme.
Curtains cold to 40°C Max. load 2.0 kg Item Curtains, including net curtains, specified as machine-washable by the manufacturer. A pre-rinse without detergent is carried out automatically to remove dust. Note For curtains which crease easily, reduce the spin speed or deselect it.
First wash cold to 40°C Max. load 3.0 kg Fabric New items made of cotton, towelling and polyester fabrics. Note Use this programme to wash any chemical residues out of new items.
Main wash Rinses Spinning Water level Wash rhythm Water level Rinses Interim spin Final spin Cottons d a ( 2-4 3)4) LL Minimum iron ( c e 2-3 5) LL Delicates e d e 3 – L Woollens e e e 2 LL Automati.
This machine has fully electronic controls with automatic load recognition. It takes in the right amount of water required for the programme depending on the amount of laundry and its absorbency rate. This means that programme cycles and durations can vary.
Washing The figure quoted in the bucket is the maximum temperature the garment can be washed at. The number of bars under the symbol indicates the level of agitation permitted.
Cancelling a programme You can cancel a programme at any time after it has started. ^ Press the Start/Stop button. Stopped: Cancel programme Continue OK ^ Press the right hand Menu button under OK . The suds will be pumped away. If you want to remove the laundry: ^ Press the Door button.
Adding or removing laundry after a programme has started ^ Press the Door button to open the drum door. ^ Add or remove items. ^ Close the drum door. The programme will continue automatically. Please note: Once a programme has started the machine cannot recognise any adjustment to the load.
The correct detergent All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads.
The right amount to dispense will depend on the following: – The quantity of the laundry – The soiling level of the laundry Lightly soiled No visible dirt or stains. Possibly slight body odour. Normally soiled Visibly dirty and/or just a few slight stains.
Fabric conditioners and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stiffens and gives body to items of laundry, e.
, Disconnect the machine from the mains electricity supply and withdraw the plug from the socket before cleaning the machine. , The washing machine must not be hosed down. A range of Miele branded cleaning and conditioning products are available to order from your Dealer, the Miele Spare Parts Department or via the internet on www.
Cleaning the siphon and conditioner channel 1 . Remove the siphon from compartment § and rinse under warm running water. Clean the siphon tube in the same way. 2 . Replace the siphon. ^ Clean the fabric conditioner channel using a brush and warm water.
Cleaning the filter in the water inlet The washing machine has a filter to protect the water inlet valve. The accessible filter in the union in the open end of the inlet hose should be checked every six months, or more often if there are frequent interruptions to the external water supply.
With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department.
Fault messages in the display Problem Possible cause Remedy A 2 Fault Check drainage system – The water outlet is blocked or restricted. – The drain hose has been fixed too high. – Clean the drain filter and the drain pump. – The maximum delivery head is 1 m.
Problems with the load size indicator or calibrating to zero Problem Possible cause Remedy The display indicates a load of <25% or no load size is indicated when the drum is full. There was already laundry in the drum when the machine was switched on.
General problems Problem Possible cause Remedy The machine shakes during the spin cycle. The machine feet are not level. Level the machine (see "Installation). The laundry has not been spun properly and is still wet. The machine detected an imbalance during the final spin and reduced the spin speed automatically.
An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. – Use a general purpose detergent containing a bleaching agent.
The door will not open Possible cause Remedy The machine is not connected to the electricity supply and/or is not switched on. Insert the plug in the socket and switch on and/or switch the machine on with the I-On/0-Off button. The safety lock has been activated.
Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever. ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine.
Once the flow of water ceases: ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff from the filter housing. Turn the impeller by hand to check that it rotates freely. Any foreign object causing an obstruction should be removed.
In the event of any faults which you cannot remedy yourself, please contact: – your Miele Dealer or – the Miele Customer Contact Centre (see back cover for contact details).
Front view a Inlet hose with "Waterproof" system b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser drawer i Drum door .
Rear view a Protruding lid for holding when moving the machine b Electricity supply cable c Inlet hose with "Waterproof" system d Drain hose e Transit bar covers f Restraining clip for inlet.
Installation surface A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note the following points: ^ The machine must be level and securely positioned.
^ Using the spanner supplied, turn the left-hand transit bar 90°, then ^ withdraw the transit bar. ^ Turn the right-hand transit bar 90°, then ^ withdraw the transit bar.
, To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed. ^ Fit the covers onto the two holes. Then plug the holes as shown with the caps. ^ Secure the transit bars to the back of the washing machine.
Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine.
Washer-dryer stack A T 200, T 4000, T 7000 or T 8000 Miele tumble dryer can be stacked on this machine using a WTV stacking kit which can be purchased from your Dealer or the Miele Spare Parts Department. Washer-dryer stack using a T 7000 series dryer and WTV 417 stacking kit a Safety distance to wall: at least 2 cm b Height: approx.
The Miele Waterproof system The Miele Waterproof system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the w.
Connection to the water supply , The plastic casing of the safety valve contains electrical components. The Waterproof system must only be connected to its own stopcock. It must not be connected to mixer taps or similar and must not be fitted in areas where there is the risk of water or other liquids reaching it.
Maintenance and care If you intend to unscrew the Miele Waterproof system hose from the stopcock it is essential to disconnect the machine from the electricity supply first.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
Load Consumption data Energy Water Duration in kWh in litres Short Normal Cottons 95°C 6.0 kg 1.99 47 2 h 09 min 60°C 1) 6.0 kg 1.02 47 1 h 49 min 60°C 3.0 kg 0.73 39 1 h 03 min 40°C 1) 6.0 kg 0.65 59 2 h 04 min 40°C 2) 3.0 kg 0.36 39 59 min Minimum iron 40°C 1) 3.
Height 850 mm Width 595 mm Depth 634 mm Depth with door open 1074 mm Weight 99 kg Maximum floor load 1,600 Newton (approx. 160 kg) Capacity 6 kg dry laundry Voltage see data plate Connected load see d.
Settings menu for changing default settings The Settings menu can be used to alter the machine's electronics to suit changing requirements. Settings can be altered at any time.
To open the Settings menu ^ Connect the machine to the electricity supply. ^ Switch on the washing machine. ^ Press both menu buttons at the same time until the following appears in the display: Settings Language ! Continue OK You are now in the Settings menu.
Gentle action Activating gentle action reduces the drum action and is suitable for washing slightly soiled items more gently. It should be activated for garments with a single bar under the care label and for articles which feel too hard after they have been dried.
Lock code The code prevents your machine being used without your knowledge. When the code has been activated, you have to enter a code after switching the washing machine on. Otherwise the washing machine cannot be operated. To activate the Lock code Lock code Activate Continue OK ^ Press the right hand Menu button under OK .
Temperature unit You can chose for the temperature to be displayed in °C/Celsius or °F/Fahrenheit . A tick L will appear beside the option to show that it has been set. Buzzer When the buzzer function has been activated, an audible tone sounds at the end of a programme or when Rinse hold is reached.
Standby display To save energy, the display goes out and the indicator light for the Start/Stop button will start flashing slowly. The display will always go out, – if a programme is not selected within 10 minutes of the machine being switched on. – 10 minutes after the end of a programme.
Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed. And now Miele have developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry.
"UltraWhite" detergent This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. "UltraColor" detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments.
Alteration rights reserved/0309/W 4446 WPS M.-Nr. 07 170 930 / 02.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele W 4446 WPS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele W 4446 WPS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele W 4446 WPS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele W 4446 WPS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele W 4446 WPS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele W 4446 WPS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele W 4446 WPS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele W 4446 WPS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
