Manuale d’uso / di manutenzione del prodotto K 1903 Vi del fabbricante Miele
Vai alla pagina of 34
Installation Instr uctions .9L.9L HQ&$ .9L.
Disposing of the packaging materials The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled.
Have the appliance installed by a qualified technician, according to the enclosed installation instructions. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions.
Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.
Base A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: K 18x3 Vi ..........9 9 6l b s (452 kg) K 19x3 Vi ......... 1,191 lbs (540 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Stainless steel panels Stainless steel door panels and toe-kick covers are available from Miele. Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: K 18x3 Vi .
Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5 / 8 " (16 mm). If there is a partition with a thickness from 5 / 8 " (16 mm) to 6 5 .
Adjusting the door opening angle (optional accessory) Depending on the installation site, it may be necessary to adjust the door opening angle to 90°. ^ Open the door. ^ Insert the banking pin through the holes and drive in with a hammer. The door opening angle is now limited to 90°.
Door dimensions (open min. 90°) *The dimensions of the door fronts and handles will vary according to each individual kitchen. 3 / 8 " (10 mm) AB C K 18X3 Vi 32 5 / 8 " (829 mm) Door front max. 1 1/2" (38 mm) Door handle* K 19X3 Vi 38 11 / 16 " (982 mm) Door front max.
Niche dimensions Niche width (A) K 18X3 Vi 30" (762 mm) K 19X3 Vi 36" (915 mm) Dimensions 44.
Power supply 1. Power supply A K 18X3 Vi 15" (381 mm) K 19X3 Vi 18" (458 mm) , Power bars or extension cords are not safe (risk of fire). Do not use them to connect the appliance to the power supply.
Door front dimensions AB K 18X3 Vi 79 1 / 8 " (2029 mm) 29 3 / 4 " (756 mm) K 19X3 Vi 79 1 / 8 " (2029 mm) 35 3 / 4 " (908 mm) 4" - 5 3/16" (102 - 132 mm) Dimensions 46 7.
Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation.
Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance. The unit corners must be at right angles, as otherwise the furniture door will not align correctly with the 4 corners of the appliance.
^ Do not remove the installation supports from the appliance door. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete.
^ Unscrew the screws a on the cover b and pull off the sticker c . ^ Remove the cover b . ^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on.
Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are numbered alphabetically. The bag needed for each step will be marked with its respective letter.
Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. If possible, always screw the wooden beam to existing studs.
Sliding the appliance into the installation space If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". ^ Unscrew the plinth. ^ To protect the corners of the installation space, attach edge protectors where needed (not included).
Aligning the appliance ^ Align the appliance with the custom front. The installation aids c on the appliance door have been designed for custom door thicknesses of 3/4" (19 mm) and 1 1/2" (38 mm).
Attaching the appliance to the installation niche ^ Screw the attachment plate lugs f to the overhead furniture/fixtures. If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. ^ Pull out the plate side lugs g .
For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance.
Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports l from the appliance door. ^ Loosen the remaining screws from the strips m on each side of the door, then remove. ^ Set aside the screws and side strips m - you will need them again later.
^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y . ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes.
Attaching and aligning the custom door front ^ Insert the angle trim m as far as it will go in the spaces provided in the mounting frame. ^ Open the door and hang the custom door with the mounting frame over the threaded bolts n . ^ Put the side strips m back into place and screw them completely down on both sides of the appliance door.
Attaching the fixing brackets (Only for appliances using the "Front panel gap kit".) The fixing brackets are used to secure the custom door front to the bottom of the appliance door. ^ Open the appliance door all the way. ^ Slightly loosen the screw (1.
^ Insert the cover strip into the space between the appliance and the wooden panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only.
^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
Accessing the RemoteVision control panel ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white. Only the access button " p " is visible.
MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network.
67.
M.-Nr. 10 101 850 / 00 en - US, CA K 1803 Vi, K 1813 Vi K 1903 Vi, K 1913 Vi.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele K 1903 Vi è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele K 1903 Vi - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele K 1903 Vi imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele K 1903 Vi ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele K 1903 Vi, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele K 1903 Vi.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele K 1903 Vi. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele K 1903 Vi insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
